Memphis Shades 2320-0030 User manual

MOUNTING INSTRUCTIONS
Figure 3
Figure 1
Space Approx.
2" apart.
WARNING:
"Mounting clamps
backwards will cause
damage to your tank."
Figure 2
MEM8928 08-18-08
Glass cleansing agents will cause severe damage
to your windshield, and will void your warranty.
NOTE: At certain times of the day the Sunlight can reflect
off the curvature of a windshield and cause extreme heat
build-up on motorcycle instruments and instrument panel.
Take care when parking. Park facing the sun, place an opaque
object over the instruments or adjust the windshield to avoid
reflections.
IMPORTANT CARE AND CLEANING INSTRUCTIONS
Memphis Shades Windshields and Lowers are made of
Lucite® acrylic, and will last for years with proper care.
Clean your windshield with plenty of soapy water — mild
dishwashing liquid is best — and a soft cotton cloth. Use your
bare hand to feel and dislodge bugs, or cover with a wet soapy
towel and let it soak. Don't use paper towels and don't scrape
with anything. Small scratches can be removed with NOVUS
# 2.
NEVER use any glass cleaning products, petroleum based
chemicals, or cleaning agents with ammonia, bleach or any
other harsh chemicals. This includes (but not limited to)
RainX, brake fluid, acetone, paint thinner, benzene and
gasoline. "If it hurts your nose, it will hurt the plastic."
No additional tools required for this kit.
1. Cover gas tank and front fender with a towel to avoid
damage during installation.
2. Install the windshield mounting plates onto the windshield,
using the bolts that are pre-assembled on the mounting plates.
The Santoprene grommets should be inserted through the
holes in the windshield so that the flat round part of the grom-
met lies flat on each side of the plastic. Tabs point in towards
the headlight. (see figure 1 )
3. Loosely install the four Fork Clamps on the forks, approxi-
mately 2" apart. (see figure 2)
4. Start with Fork Clamp Bushing adjusted to rear of slot (see
figure 4) Then adjust as needed and check for clearance. (See
warning above.)
5. Slip the windshield mounting plates and windshield onto
the fork clamps, (see figure 3 and 5) and secure the left and
right side locking mechanism
6. Adjust the height, angle and alignment of the windshield
and tighten ALL bolts.
Note: This is a detachable windshield, ALWAYS make
sure the Locking Mechanism is Fully Engaged after in-
stalling the windshield! (see figure 5)
Start with Fork Clamp Bushing ad-
justed to rear of slot. Then adjust as
needed and check for clearance. (See
above "Read and Follow Directions
Warning.")
Fig. 4
Bushings
Throttle side,
front of bike
INCORRECT
CORRECT
2320-0030 SPORTSHIELD DETACHABLE MOUNTING KIT 06-07 DYNA's
FXDI, FXDCI, FXDBI, FXDI35, FXDC, FXDLI
Read and follow these directions carefully.
During installation, make sure that the windshield and hard-
ware do not interfere with any cables or wiring when the forks
are turned all the way in either direction. Also make sure,
through the full range of adjustment, that the windshield and
hardware do not hit the tank.
This is a detachable windshield, ALWAYS make sure the
Locking Mechanism is Fully Engaged after installing the
windshield!
The improper installation of this kit and related compo-
nents could result in serious injury or death.

2320-0030 SORTSHIELD DETACHABLE MOUNTING KIT 06-07 DYNA's
FXDI, FXDCI, FXDBI, FXDI35, FXDC, FXDLI
MOUNTING INSTRUCTIONS
MEM8928 08-18-08
CORRECT
Fully engaged
NOT CORRECT
1. Place lower slot into lower bushing. 2. Rotate top slot into
place. 3. & 4. Secure locking Mechanism.
123
Figure 5
4
Loosen Allen Bolt to adjust angle, then re-tighten Allen Bolt.
R322C/T
LATCH
ASSEMBLY
1. M533
2. M520
3. M1139
4. M1140
2
3
1
BUSHING
ASSEMBLY
4
2320-0030 SPORTSHIELD KIT
BUSHING ASSEMBLY
A C
C
D
E
F
A. R329
B. M369
C. R323
D. R324
E. R318
F. M306
B
PART #
M8928
M543
DESCRIPTION
MOUNTING INSTRUCTIONS
SANTOPRENE GROMMET
M504
M505
SOCKET SHOULDER WASHER
BUTTON NUT
4
4
4
M302
1/4"-20 x 1/2” SS SOCKET HEAD CAP SCREW 4
M1140 RIGHT SPORTSHIELD MOUNTING PLATE 1
M1139
LEFT SPORTSHIELD MOUNTING PLATE
QTY.
1
1
M520
INNER ADJUSTABLE FORK CLAMP 4
M533
MEDIUM OUTER DETACHABLE ADJ. FORK CLAMP 4
PART #
M369
DESCRIPTION
STAINLESS STEEL WASHER
M306 1/4"-20 x 5/8" SS SOCKET HEAD CAP SCREW 4
4
M313 3/16" ALLEN WRENCH COVER 1
QTY.
M310 3/16" SHORT ARM ALLEN WRENCH 1
R329 SLOT NUT 4
R323
BUSHING ASSEMBLY (2 PART) 4
R318
1" SOCKET SHOULDER WASHER 4
R324
#207 EPDM O-RING 4
R322 C/T LATCH ASSEMBLY 2M303 1/4"-20 x 3/4” SS SOCKET HEAD CAP SCREW 4
Memphis Shades warrants all product components, metal and plastic,
against defects in materials and workmanship for 24 months.
FOR PARTS AND WARRANTY HELP, CONTACT:
MEMPHIS SHADES
P. O. Box 429
Rossville, TN 38066
[phone]
Visit us on the web at www.memphisshades.com or
You can also reach us at
[email protected]