Memphis Shades 2321-0243 User manual

Glass cleansing agents will cause severe damage
to your windshield, and will void your warranty.
NOTE: At certain times of the day the Sunlight can reflect
off the curvature of a windshield and cause extreme heat
build-up on motorcycle instruments and instrument panel.
Take care when parking. Park facing the sun, place an opaque
object over the instruments or adjust the windshield to avoid
reflections.
IMPORTANT CARE AND CLEANING INSTRUCTIONS
Memphis Shades Windshields and Lowers are made of
Lucite® acrylic, and will last for years with proper care.
Clean your windshield with plenty of soapy water — mild
dishwashing liquid is best — and a soft cotton cloth. Use your
bare hand to feel and dislodge bugs, or cover with a wet soapy
towel and let it soak. Don't use paper towels and don't scrape
with anything. Small scratches can be removed with NOVUS
# 2.
NEVER use any glass cleaning products, petroleum based
chemicals, or cleaning agents with ammonia, bleach or any
other harsh chemicals. This includes (but not limited to)
RainX, brake fluid, acetone, paint thinner, benzene and
gasoline. "If it hurts your nose, it will hurt the plastic."
7. Install the windshield by placing the lower slots into the
lower mounting bushings. Slip the upper slots into the upper
mounting bushings and gently but firmly seat the slots into
place.
Lock the locking mechanism into place. (see figure 4)
8. Tighten all mounting bolts. Adjust the height, angle and align-
ment of the windshield and tighten ALL bolts. (See Figure 5)
Note: This is a detachable windshield, ALWAYS make
sure the Locking Mechanism is Fully Engaged after in-
stalling the windshield! (see figure 4)
MOUNTING INSTRUCTIONS
2321-0243 SPORTSHIELD YAMAHA 1300 V-STAR DETACHABLE, BLACK
Figure 1
Figure 3
MEB8921 07/14/11
Read and follow these directions carefully.
During installation, make certain that when turning the
forks, there can be no interference with wiring or cables
AND, that the windshield can not hit the gas tank,
through the windshield's full range of adjustment.
This is a detachable windshield, ALWAYS make sure the
Locking Mechanism is Fully Engaged after installing the
windshield!
The improper installation of this kit and related compo-
nents could result in serious injury or death.
Additional tools required, that are not included in this kit. Thin
blade screwdriver to pry-up trim topper.
1.Cover gas tank and front fender with towels to avoid
damage during installation.
2. Install the windshield mounting plates onto the windshield,
using the bolts that are pre-assembled on the mounting plates.
The Santoprene grommets should be inserted through the
holes in the windshield so that the flat round part lies flat on
each side of the plastic. NOTE: Tabs will point in towards
headlight when properly installed. (see Figure 1)
3. Locate and remove the two trim toppers, located on the
upper triple tree. (see Figure 2)
4. Using a 4mm Allen wrench remove the lower Turn Signal trim.
Take care not to loose the small Brass Bushings. Also remove both
Turn Signals with a 5mm Allen wrench. (See Figure 2)
5. Install throttle side bracket by loosely installing new 10mm
x 20mm SS Button Head Bolt with one washer in front and
two washers on back in upper triple tree as shown in Fig 3,
Screw, washer, bracket then two washers.
6. Install Turn Signal and lower Bracket using new 8mm Socket
Head Cap Screw with Spacer and washer in this order; Screw,
washer, bracket, spacer and through Turn Signal and loosely
tighten into lower triple tree. Tighten both upper and lower
screw. (See figure 3) Repeat steps 5 and 6 on Clutch side.
Figure 2
Turn Signal Trim

7
31
5
8
9
2 4
6
BUSHING
ASSEMBLY
1. M1142
2. M1140
3. M1141
4. M1139
5. R349
6. R337
7. M366
8. R312
9. R336
CORRECT
Fully engaged
NOT CORRECT
BUSHING ASSEMBLY
1. Place lower slot into lower bushing. 2. Rotate top slot into
place. 3. & 4. Secure locking Mechanism.
123
Figure 4
4
A
B
C
C
D E
A. M505
B. R321
C. R323
D. R324
E. R318
F. M303
F
Loosen Allen Bolt to adjust angle, then re-tighten Allen Bolt.
Figure 5
R322C/T
LATCH
ASSEMBLY
MOUNTING INSTRUCTIONS
2321-0243 SPORTSHIELD YAMAHA 1300 V-STAR DETACHABLE,BLACK
Memphis Shades warrants all product components, metal and plastic,
against defects in materials and workmanship for 24 months.
FOR PARTS AND WARRANTY HELP, CONTACT:
MEMPHIS SHADES
P. O. Box 429
Rossville, TN 38066
[phone]
Visit us on the web at www.memphisshades.com or
you can also reach us at
[email protected]
Part# Description Qty
I8921B Mounting Instructions 1
M1139EB Left Sports Plate, Black 1
M1140EB Right Sports Plate, Black 1
M1141 Left 1300 V-Star Bracket 1
M1142 Right 1300 V-Star Bracket 1
R349 10mm x 20mm SS Button Head Bolt 2
R337 10mm SS Washer 6
M366 8mm x 30mm Socket Head Cap Screw 2
R312 8mm SS Flat Washer 2
R336 3/4”x3/8” Lower Bolt Spacer 2
R323 Bushing Assembly (2 part) 4
R324 #207 EPDM O-Ring 4
R318 1” Socket Shoulder Washer 4
Part# Description Qty
R321 1” Recessed Spacer 4
M543 Santoprene Grommet 4
M504 Socket Shoulder Washer 4
M302 1/4”-20x1/2” Socket Head Cap Screw 4
M505 Button Nut 8
R322C Clutch Side Latch Assembly 1
R322T Throttle Side Latch Assembly 1
R334 6-32x3/8” Flat Head SS Screw 8
R326 SS Spring 2
M310 3/16” Short Arm Allen Wrench 1
M313 3/16” Allen Wrench Cover 1
M312 4mm Short Arm Allen Wrench 1
R306 5mm Long Arm Allen Wrench 1
M311 6mm Short Arm Allen Wrench 1
M303 1/4”-20x3/4” Socket Head Cap Screw 4