Meridian FIT-AOXIN-M2-AN2E User manual

 
   
  




&

IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your machine before using your
machine. We assume no responsibility for personal injury or property damage
sustained by or through the use of this product.
1. Please read, understand manual and all warnings, test the usage before using the
machine. It is the responsibility of the owner to ensure that all users of this machine
are adequately informed of all warnings and precautions.
2. Retain this user manual for current and future reference, and make sure all warning
labels are clear and complete.
3. This machine is recommended to be installed by at least two adults.
4. Before beginning this or any exercise program, consult your physician. This is
especially important for persons over age 35 or persons with pre-existing health
problems.
5. Keep children and pets away and safe from the machine at all times.
6. Pulleys and cables should be checked for wear frequently and replaced as needed,
so as to avoid any danger to you or the people around.
7. Wear appropriate exercise clothes while using the machine.
8. Inspect and properly tighten all parts of the machine regularly, especially ropes to
avoid any injury. If something is wrong, stop using and contact our after-sales service
department for support.
9. Required Tools: Spanner and Allen wrench
• Product may vary slightly from item pictured due to model upgrades.
• Please check the packing details before assembly, if there is any missing part,
contact after-sales service department for support.
• Please read all instructions carefully before using the product. Retain this user
manual for future reference.

3
Final Picture

4
Spare parts list
Item
no.
Description
QTY
Item
no.
Description
QTY
1
Main bottom frame
1
37
M10x55 Bolt
2
2
Front bottom frame
1
38
Arm seat
1
3
40x80 flat oval tube
1
39
Back seat
1
4
Front Upright
1
40
Seat
1
5
Weight guide tube
2
41
Knob
2
6
Butterfly handle bar
2
42
Φ19 Bushing
2
7
Air frame
1
43
Air frame knob
1
8
Upper cross beam
1
44
Foam endcap
4
9
Seat bracket
1
45
38x38 square Endcap
4
10
Seat bracket holder
1
46
25x50 square Endcap
2
11
Right butterfly arm
1
47
40x80 Endcap
3
12
Left butterfly arm
1
48
38x38 Endcap
2
13
Leg frame
1
49
40x80 Endcap
5
14
Arm seat frame
1
50
Round cushion plates
2
15
Air frame fix shaft
1
51
Φ50 plastic bearing
4
16
Air frame screw
1
52
50 round endcap
1
17
Connection plate
2
53
50x50 square bearing
1
18
Seat frame
1
54
Back upper cross beam
1
19
Pulley
16
55
Φ8 Flat washer
18
20
Pulley cross U frame
1
56
Φ10 Flat washer
74
21
Pulley single U frame
2
57
AB belt
1
22
Lat bar
1
58
(2040mm）AB belt cable
1
23
Rower bar
1
59
Φ10 Big flat washer
4
24
Adjustment plate
2
61
M8x16 Hex bolt
14
25
Foam tube（Φ25x380mm）
2
62
Pulley U
1
26
weight plate top cover
1
63
M8x40 Hex bolt
1
27
Weight plate
12
64
M8x55 Hex bolt
2
28
Φ12 Big flat washer
1
65
M10x25 Hex bolt
11
29
Weight plate latch
1
66
M10x45 Hex bolt
16
30
Weight plate bar pushing
1
67
Metal cover
1
31
Weight plate bar
1
68
M10x60 Hex bolt
4
32
Weight plate cushion
2
69
M10x65 Hex bolt
2
33
L Latch
1
70
M10x70 Hex bolt
1
34
Φ80x160 Foam
4
71
M10x100 Hex bolt
5
35
Φ90x245 Foam
2
72
M10x110 Hex bolt
2

5
36
Φ28Handle bar
4
73
M10x20 Hex bolt
2
74
Nut M8
1
79
（2900mm）Butterfly cable
1
75
Nut M10
37
80
（2770mm）Row bar cable
1
76
Pothook
7
81
（490mm）Chain(long)
1
77
(280mm）Chain( short)
2
82
Ankle belt
1
78
(2650mm）Lat bar cable
1

6

7

8
Assembly Steps
Attention:
1. Put the washers to the two ends of the bolts.
2. For pre-assembly, put the bolts and screws are in the position, and tighten them with spanner
after the full assembly.
3. Some parts are put in the machines already.
4.Suggest to assembly it by at least two persons.
Picture 1
1. Put the main bottom frame(#1) side with 3pcs holes in the upper, attach the weight guide
tube( #5) to the main frame(#1), using 2pcs hex bolts M10x20（#73）.
2. Attach main bottom frame(#1) and front bottom frame(#2), using 2pcs M10x25 hex bolts（#65），
4pcs flat washers Φ10（#56）和2pcs M10 nuts（#75）.
3. Tighten all the bolts by spanner, put weight plate cushion (#32) through the weight guide tube
(#5).

9
Assembly Step
Picture 2
1. Attach weight plate(#27) to the weight guide tube(#5) by turn( groove side is under)，attach
weight plate bar pushing(#30) to the weight plate bar(#31), make the holes in the right position.
Attach weight plate latch (#29) to the holes of the weight plates.
2. Attach weight plate top cover (#26) to weight plate bar(#31) and weight plate bushing(#30),
using big flat washer Φ12（#28）to the weight plate top cover (#26), and put L latch（#33） to
weight plate bar(#31).
3. Attach front upright（#4）to Front bottom frame（#2）, using 3pcs M10x100 hex bolts(#71), 6pcs
flat washers Φ10（#56） and 3pcs M10 nuts（#75）.
4. Attach upper cross beam(#8) to the connection plate（#17）, using 2pcs M10x60 hex bolts（#68）,
4pcs flat washers Φ10（#56）, 2pcs M10 nuts （#75）. Attach upper cross beam(#8), back cross
beam(#54) to weight guide tube(#5), using 2pcs M10x25 hex bolts(#65) and 2pcs flat washers
Φ10（#56）.
5. Attach pulley U (#21) to Pulley single U frame(#4), using 1pce M10x65 hex bolts(#69), 2pcs flat
washers Φ10（#56）and 1pce M10 nut(#75).

10
Assembly step
Picture 3
1. Attached back seat(#39) to front upright( #4), using 2pcs M8x55 hex bolts(#64) and 2pcs flat
washers Φ8（#55）.
2. Attach air frame bolt (#16) to front upright( #4), using 1pce M8x40 hex bolt(#63), 2pcs flat
washers Φ8（#55） and 1pce M8 nut (#74), put the knob (#43) to the air frame bolt( #16).
3. Attach air frame (#7) to upper cross beam(#8) by air frame fix shaft(#15), using 2pcs M10x25
bolts(#65) and 2pcs flat washers Φ10（#59）to tighten air frame fix shaft(#15).

11
Assembly Step
Picture 4
1. Attach right butterfly arm(#11) to the U frame of air frame(#7), using 1pce M10x110 hex
bolt(#72), 2pcs flat washers Φ10（#56）and 1pce M10 nut (#75).
2. Attach Φ90x245 foam（#35）to the right butterfly arm(#11).
3. Attach handle bar( #6) to the right butterfly arm(#11), using 1pce M10x25 hex bolt(#65) and
1pce flat washerΦ10（#59）.
4. Attach left butterfly arm (#12) to the U frame of air frame ( #7) by the same way.

12
Assembly Step
Picture 5
1. Attach the seat holder frame(#18) to the front upright(#4), using 2pcs M10x60 hex bolts(#68),
4pcs flat washers Φ10（#56）,1pce connection plate(#17) and 2pcs M10 nuts (#75).
2. Attach seat bracket holder(#10) to the seat holder frame(#18), using 2pcs M10x55 bolts(#37),
2pcs flat washers Φ10（#56）and 2pcs M10 nuts (#75).
3. Attach seat bracket holder(#10) to the front bottom frame (#2), using 2pcs M10x100 hex
bolts(#71), 4pcs flat washers Φ10（#56）and 2pcs M10 nuts(#75).
4. Attach Leg frame (#13) to the seat bracket holder(#10), using 1pce M10x70 hex bolt(#70), 2pcs
flat washers Φ10（#56）and 1pce M10 nut(#75).

13
Assembly Step
Picture 6
1. Attach arm seat(#38) to the arm seat frame(#14), using 4pcs M8x16 hex bolts(#61), 4pcs flat
washers Φ8（#55）.
2. Attach the arm seat frame (#14) to the seat bracket holder(#10), tighten the knob(#41).
3. Attach seat (#40) to the seat frame(#9), using 4pcs M8x16 hex bolts(#61) and 4pcs flat washers
Φ8（#55）.
4. Attach seat bracket (#9) to the seat frame(#18), tighten the knob(#41).

14
Assembly step
Picture 7
1. Attach 2pcs foam tube (#25) to the leg frame (#13) and the seat bracket holder (#10).
2. Attach Φ80x160 foam (#34) to the foam tube.
3. Attach the endcap (#44) to the foam tube.

15
Assembly step
Picture 8: chain cables assembly step
Check the cables, if the cables are loosen, adjust it by lat bar cable (#78), if the cables are too loosen,
adjust it by adjustment plate (#24).
butterfly cable（#79）length 2900mm
Tighten the cables by the
connection plate（#24）
Tighten Lat bar cable（#78）by the bolt
and nut
Keep 3-5MM distance
Lat bar cable（#78）length 2650mm
Row bar cable（#80）length 2770mm
AB belt cable （#58 ）length
2040mm

16
Assembly step
Picture 9
1. Attach metal cover ( #67) to the upper cross beam (#8), the main bottom frame (#1) and front
bottom frame (#2), using 6pcs M8x16 hex bolts (#61) and 6pcsΦ8 flat washers (# 55).

Finally:
1. Please tighten all bolts and nuts firmly by spanner, not by hand.
2. Now the whole machine has been assembled completely.
3. Make sure to check all pulleys and cables before using your machine.
4. Please adjust cables according to actual situation at the beginning.
& &
Maintenance :
Your home gym is designed to be reliable and easy to use. In order to extend the
service life of the machine, its components must be lubricated on time. Lubrication
has been done before the machine leaving factory, but after a certain period of
usage, lubrication and maintenance must be carried on especially on the weight
plate guide rods.
Note: It is
forbidden
to use machinery oil and grease, otherwise after days of expos
ure, an oil can turn in to more of a honing compound than a lubricating medium cau
sed by tiny dust particles from the air.
Sewing machine oil
is recommended.
1. Cables are wearable items. It is your responsibility to prevent unexpected
breakage. Cable inspection should be performed daily. Inspect all cables and
pulleys, and the area near the fitting at each end of each cable. Replace any
damaged or worn cable immediately. Do not allow the machine to be used until
these are replaced.
2. Please check or adjust cables tension regularly.
3. All parts and functions should be checked regularly to ensure correct operation.
4. If you experience problems, first recheck the assembly instructions to locate any
possible errors made during assembly. If you are unable to correct the problem,
please contact our after-sales service for support.
5. If any worn or unexpected breakage, please stop using machine immediately
and contact our after-sales service for support.
6. During inspection, please make sure all bolts and nuts are tightened firmly.
7. Remember to check and make sure all welds are crack-free.
8. Failure daily care and maintenance may lead to injury on people or equipment
damage.