MERLYN arysto six User manual

Installation Guide
One door quadrant
Right hand
Door
opening
direction
Door
opening
direction
Left hand

IMPORTANT:
Please read the complete instructions
before commencing fitting.
The wall plugs supplied with the installation kit are for use
in solid walls. Hollow or ‘stud partition’ walls will require
alternative fixings. Please consult a hardware supplier for
the correct type.
It may also be necessary to consult your tiling supplier
about the correct method for drilling tiles.
ATTENTION: TAKE EXTREME CARE WHEN HANDLING
GLASS, WEAR PROTECTIVE EYEWEAR AND CLOTHING.
DO NOT LEAVE THE GLASS ON HARD SURFACES AND
AVOID CONTACT BETWEEN THE GLASS EDGES AND
HARD SURFACES OR IMPACTS DURING THE
INSTALLATION.
Make sure the tray is 100% level in all directions.
Do Not attempt to install the product unless you can tick all
4 boxes satisfactory.
· Check that you have the tools required
· Check the installation site is compatible with the sizes
of door supplied
· Check all the enclosure components are present
· Check the installation kit is complete

1
1
2
2
8
10
8
2
1
1
1
1
1
1
1
1
1
2
1
1
1
3
01
02
03
04
05
06
21 22
23
07
12
12
08
09
10
07
11
13
14
15
16
17
18
19
20
01
02
03
04
05
06
07
08
09
10
11
12
16
17
18
20
21
22
23
19
13
15
14
No. QTY Description No. QTY Description CodeCode
Top cap for wall profile, left A6WPCAPL
A6STDWPWall profile
A6WPLUGWall plug
A64X8FRAFrame fixing screw
A6WSCRWPan head wall screw
Fixed panel
U shape bottom seal A6SLFIXPS
Sliding door/ 1 door quad
roller, Top left A6SLROLTL
Sliding door/ 1 door quad
roller, Bottom left A6SLROLBL
1
A6HANDLEHandle
Top cap for wall profile, right A6WPCAPR
Top cap for adjusting profile, left A6UPPCAPL Top cap for adjusting profile, right A6UPPCAPR
Profile filler piece A6PROFILL
Flat fixed panel
Moving door
2
Cover strip A6STDCS
One door quad Top/bottom rail A61DQTBP*
One door quad roller, Bottom right
One door quad roller, Top right A61DQROLTR
A61DQROLBR
Upright seal for one door quad A61DQUPS
Upright water seal 15mm for 1 door
quadrant fixed AR1QUPSF
Upright water seal 15mm for 1 door
quadrant moving AR1QUPSM
*Please note that the top and bottom profile code will change depending on enclosure size. For example- 900mm= A691DQTBP

A6SLROLTL A6SLROLBL A6PROFILL
A61DQROLTR A61DQROLBR
Fixing Kit Components
Tools required
x1 x1 x1 x1
x1x1
x1 x1 x1 x1
Philips
x1
x1
2.5mm
4
Ø3
Ø6
A6WPLUGA64X8FRA A6WSCRW
ST4*8 ST4*30
x10 x8x8
Ø6
A6UPPCAPL A6UPPCAPR A6WPCAPL A6WPCAPR
x1
1&1.5mm 2&3mm
x1
AR6SPACER1 AR6SPACER2
A6HANDLE

100%Level!
2
Note: This is a handed product but is shown in left hand configuration for
illustration purposes.
5
Ensure the shower tray is level in all
directions and is properly sealed to
the wall. The wall must be tiled down
to the top edge of the tray. Do not
angle out bottom tile.
TRAY MUST BE LEVEL IN ALL
DIRECTIONS!
TRAY MUST BE SEALED FULLY
IN ALL AREAS WHERE
THE TRAY MEETS THE WALL.
1
X
X
X
Y
Y
Y
(900 x 760) 855-880
X
715-740
Size Y
(1000 x 800) 955-980 755-780
(1200 x 800) 1155-1180
1155-1180
755-780
855-880
955-980 955-980
855-880
855-880
(900 x 900)
(1000 x 1000)
(1200 x 900)

3
3A
Min 10mm
4
4A
Min 10mm
3B
4B
6

Fixed panel
Flat fixed
panel
Push the seal onto the fixed panel making sure it is 10mm from the edge.
NOTE: After step 9 make sure seal is still in the same position.
5B
Φ6
5A
5
No gap
7
6

7
8
7A
7C
8A
8B
7D
8
8C
7B
8D

9
10
9B 9D
7
9A 9C
10A 10B

11
11B
11A
12
12A
12B
12C
12D
9

13 Where possible the frame should be adjusted equally on both sides, A=B.
Max. adjustment of each side (A&B) is 25mm.
AB
14 Make sure the bottom profile is level. If level continue to step 15. If not level choose
a spacer size from AR6SPACER1/A6SPACER2 that returns the profile to level.
14A
AR6SPACER1
AR6SPACER2
14B
10

Min4mm
Min15mm
15A
15B
Min4mm
Min15mm
15C
15D
15 15A ,15C From inside drill the frame top, middle and bottom making sure to step in a
Min. 15mm from the edge of the frame.
15B,15D On Max. adjustment drill 4mm from the edge of the frame as shown below.
100mm
100mm
100mm
100mm
16
16A 16B
11

18
18A
18B
18C
18D
RELEASE
OUTSIDE
TOP LEFT TOP RIGHT
TOP ROLLERS ASSEMBLY
BOTTOM ROLLERS ASSEMBLY
BOTTOM LEFT BOTTOM RIGHT
17B
17A
17C
17 After the handing has been determined fix the rollers to the moving panel as
shown in 17A. Note: Please check the roller labeling for correct orientation.
12
PUSH

20
20A
20B
INSIDE
INSIDE
INSIDE
2.5mm
INSIDE
OUTSIDE
INSIDE
INSIDE
INSIDE
19A
19B
19
13

21 Adjust the rollers to plumb the moving panel. Also ensure the bottom rollers are in
contact with the profile.
22 There should be no gap between both roller arms and the roller stops.
Adjust rollers up or down to allow for full insertion.
14

23
23A
23B
24
24 h.
50mm
15

It is important to clean your Merlyn shower door after every use. Wipe down all the glass and
metal parts with a soft cloth. Do not allow lime scale to build up in hard water areas. Ensure
that any residual water on the glass is removed after every use.
· Clean the glass regularly using soapy water.
· Do not use abrasive products on any surfaces.
Chrome is vulnerable to acid attack and some strong household cleaners including strong
disinfectants, denture cleaners, hair dyes, wine making chemicals and photographic chemicals
may contain acid. These materials may have a varying effect on the surface from black
spots/streaks (which cannot be removed) to pitting the surface. Contact with these materials
should be avoided.
1. Is the tray 100% level? ( see page 5)
2. Have the walls been checked at different levels to ensure consistency? Bumps or hollows
in the wall may push the frame out of alignment.
3. Are the wall profiles stepped in a Min. 10mm from the edge of the tray? ( see step 3,4)
4. Do the finished tile measurements at top, middle and bottom fall within the adjustment (X)
listed on step 2.
5. Are the rollers adjusted so the bottom rollers are running along the track in the frame and
not rattling in the bottom track (see step 21)
6. Are the rollers adjusted so the closing side roller arm goes fully into the roller stop (see
step 22).
7. If bottom roller easy clean function does not work correctly slightly loosen the screws on
the top rollers (see step 21).
1. This door is fitted with a soft close roller stop. Make sure the door is fully closed (see
step 22). To ensure the best performance of the soft close periodical cleaning of the stop
with a damp cloth may be required.
2. Are the rollers adjusted so the closing side roller arm goes fully into the roller stop on the
top and bottom ? (see step 22)
3. Are the upright seals fitted correctly (see step 19)
4. Is the door sealed correctly ? (see step 24)
5. Have the fixed panels been properly secured? (See step 15)
6. Ensure a sufficient dab of silicone is applied between fixed clip and glass on bottom
profile and upright seal is fitted to fixed panel. Then remove excess silicone. (See step 24)
7. Check to ensure the door frame is 100% square.
CLEANING
Door Not Aligning
TROUBLE SHOOTING
Door Leaking
16

To download the Declaration of Performance (DOP) for this product use the link below.
http://merlynshowering.com/aftersales-support/dop-certs/
For further information contact IRL: 056 7791 888, UK: 0808 1011 429
Merlyn Industrles Ltd (MER01)
CEAR6 1.1
18
EN 14428
Cleanability : Pass
Impact resistance/
shatter propertles
Durablily
Shower enclosures with aluminium
profiles and safety glass
: Pass
: Pass
M099
17