Metra Electronics 99-9600 User manual

APPLICATIONS
CAUTION: Metra recommends disconnecting the
negative battery terminal before beginning any
installation. All accessories, switches, and especially
air bag indicator lights must be plugged in before
reconnecting the battery or cycling the ignition.
NOTE: Refer to the instructions included with the
aftermarket radio.
INSTALLATION INSTRUCTIONS FOR PART 99-9600
• ISODINradioprovision
•Pre-wiredASWC-1harnessincluded (Axxess ASWC-1
is sold seperately, for retention of handlebar controls)
•A)Radiohousing•B)Rubbergasket•C)(4)1/2”longbutton-headcapscrews
•D)Harness(notshown)
KIT FEATURES
KIT COMPONENTS
WIRING & ANTENNA CONNECTIONS(soldseparately)
WiringHarness:•Included
AntennaAdapter:•Notrequired
• Panelremovaltool•Phillipsscrewdriver
• Socketwrench(T-25,T-27,6mmor3/16hex)
TOOLS REQUIRED
Harley-Davidson 1998-2013
(FL models with fairings)
99-9600
A B C

99-9600
FLH/Batwing models:
1. Coverthefrontfender.
2. Remove(2)T-27Torxboltsfrominner
fairing(undermirrors)(FigureA,step2)
3. Remove(2)T-27Torxboltsfromouter
edgesofinnerfairingneartheforktubes
(facingforward)(FigureA,step3)
4. Remove(3)T-27Torxboltsfrombottom
edgeofwindshield.(FigureA,step4)
NOTE: Windshield and fairing
will be loose once these screws
are removed. Use extreme
caution not to damage fairing or
windshield.
5. Removewindshieldtakingcautionthat
theouterfairingisloose.

Fairing Disassembly
(Figure A)
Step 2 Step 2
Step 3
Step 4

99-9600
FLH/Batwing models: (cont.)
6. Liftawayandunplugheadlightto
removeouterfairing.(FigureB)
7. Extract(2)3/16”Allenboltsfromeach
sideoftheradiohousing.(FigureC)
8. Removethefactoryradio.

Fairing Disassembly
(Figure B) (Figure C)

99-9600
Fairing Disassembly
Roadglide/Sharknose models
1. Loosen(6)T-25Torxboltsfrom
bottom,middleandtopofleftand
rightsidesoftheinnerfairing.
(FigureA)

(Figure A)
Step 1 Step 1

99-9600
Fairing Disassembly
Roadglide/Sharknose models (cont.)
2. Usea1/2”socketorboxwrench
toremovethe(2)acornnutsthat
holdeachturnsignalatthelower
fairing.Letthesignalshangloose.
(FigureB)
3. Liftawaythefairing,unplugthe
headlightsandremove.
4. Remove(2)3/16”Allenboltsfrom
eachsideoftheradiohousing.
(FigureC)

(Figure B) (Figure C)

ISO DIN radio provision
(Figure A) (Figure B)
1. Slidetheradiointoradiohousing
andsecurewithscrewssupplied
withtheradio.(FigureA)
2. Slidetherubbergasketoverthe
frontedgeoftheradiohousing.
(FigureA)
3. Inserttheradioandkitassembly
intothefactoryradioopeningfrom
thebacksideoftheinnerfairing.
(FigureB)
4. Securewiththefactoryhardware,
ortheincludedbutton-head
screws.(FigureB)
5. Locatethefactorywiringharness
andantennapluginthedash.
Metrarecommendsusingthe
propermatingadapters.Usethe
includedwiringharness.The
AXXESSASWC-1interfaceissold
separatelyforretentionoffactory
handlebarcontrols.
6. Reassemblebikeinreverseorder
ofdisassembly.
Optional
spacers if
needed
Kit Assembly 99-9600

Connections to be made
From the 23-pin harness
(a) to the aftermarket radio:
• ConnecttheBlackwiretothegroundwire.
• ConnecttheYellowwiretothebatterywire.
• ConnecttheRedwiretotheaccessorywire.
• ConnecttheWhitewiretotheleftfront
positivespeakeroutput.
• ConnecttheWhite/Blackwiretotheleft
frontnegativespeakeroutput.
• ConnecttheGray wiretotherightfront
positivespeakeroutput.
• ConnecttheGray/Blackwiretotheright
frontnegativespeakeroutput.
(b) to the vehicle:
• IftheASWC-1(soldseparately)istobe
used,connectthePink/Whitewiretothe
Pink/Whitewirefromthevehicle.Thiswire
islocatedneartheleftsidespeakerina
harness,andgoestotheleftsidehandlebar
controls(theclutchside).The Pink/White
wirefromthevehicleneedstobecut,and
thePink/White wirefromthe23-pinharness
connectedtowardstheleftsidehandlebar
controls(theclutchside).(FigureA)
From the 12-pin harness to the aftermarket radio:
• The12-pinharnessistobeusedinconjunction
withtheoptionalASWC-1(notincluded)toretain
steeringwheelcontrols.IftheASWC-1isnot
beingused,disregardthisharness.Ifitwillbe
used,pleaserefertotheASWC-1instructionsfor
radioconnectionsandprogramming.
Wiring Instructions 99-9600
Figure A
Connect Pink/White
wire (99-9600) to the
Pink/White wire from
factory harness