Metra Electronics ABTI-GM4 User manual

Refer to the IHF-1000 manual for operation. All audio signals from
the IHF-1000 will be played through the car stereo. Adjust the vol-
ume using the radio’svolume knob to a comfortable level. Audio
from FM, CD, Satellite etc. will be automatically paused or muted
while calls are in process. Any OnStar operations will preempt the
operation of the IHF-1000. Keep in mind that if OnStar operations
start while you are on a call, the call will continue and the caller will
be able to hear you – watch what you say!
The vehicle’sradio does not need to be on for IHF-1000 operations,
but the vehicle’s ignition must be on or in accessory mode.
ABTI-GM4
©Copyright 2007 Metra Electronics Corporation
1-800-221-0932 www.metraonline.com
ABTI-GM4
©Copyright 2007 Metra Electronics Corporation
1-800-221-0932 www.metraonline.com
4
ABTI-GM4 ABTI-GM4
A
AP PP PL LI IC CA AT TI IO ON NS SI IN NC CL LU UD DE E: :
REV. 08/24/07 INSTABTI-GM4
* READ IMPORTANT WARNING ON PAGE 1
BEFORE ATTEMPTING ANY INSTALLATION
SATURN
GENERAL MOTORS
LAN
BLUETOOTH INTERFACE
INSTALLATION MANUAL
5) Connect the 14 pin cap on the ABTI-GM4 cable to the 14 pin
plug connected to the vehicle (the connector that was removed
from the back of the radio).
10) Install the IHF-1000 microphone in an appropriate location
(see IHF-1000 instructions), route the wire to the IHF-1000 har-
ness, and attach the microphone connector to the harness.
11) Secure all components, and reinstall the radio.
12) Reconnect the vehicle battery.
6) Connect the 16 pin cap on the ABTI-GM4 cable to the 16 pin
plug connected to the vehicle (the connector that was removed
from the back of the radio).
ABTI-GM4
GM LAN cable harness
8pin
IHF-1000 keypad
plug
White
RE-PLUG EXISTING
FROM CAR
UNPLUG EXISTING
UNPLUG EXISTING
FROM CAR
16 pin plug
14 pin plug
RE-PLUG EXISTING
FROM CAR
FROM CAR
16 pin plug
14 pin plug
ABTI-GM4
GM LAN cable harness
8 pin
IHF-1000 keypad
plug
White
RE-PLUG EXISTING
FROM CAR
UNPLUG EXISTING
UNPLUG EXISTING
FROM CAR
16 pin plug
14 pin plug
RE-PLUG EXISTING
FROM CAR
FROM CAR
16 pin plug
14 pin plug
7) Connect the white 10-pin plug on the ABTI-GM4 cable to the
ABTI-GM4 module.
ABTI-GM4
GM LAN cable harness
8 pin
IHF-1000 keypad
plug
White
RE-PLUG EXISTING
FROM CAR
UNPLUG EXISTING
UNPLUG EXISTING
FROM CAR
16 pin plug
14 pin plug
RE-PLUG EXISTING
FROM CAR
FROM CAR
16 pin plug
14 pin plug
9) Install the IHF-1000 keypad on the dashboard of the vehicle,
and route the wire to the IHF-1000 harness. Attach the keypad
connector to the harness.
ABTI-GM4
GM LAN cable harness
8 pin
IHF-1000 keypad
plug
White
RE-PLUG EXISTING
FROM CAR
UNPLUG EXISTING
UNPLUG EXISTING
FROM CAR
16 pin plug
14 pin plug
RE-PLUG EXISTING
FROM CAR
FROM CAR
16 pin plug
14 pin plug
OPERATION
The ABTI-GM4 is designed to allow full integration of Motorola’s
IHF-1000 Bluetooth Hands free kit (Sold separately) with GMLAN
vehicles listed above. The kit will allow users to listen to phone
calls through their car stereo. The currently playing radio source
will be automatically muted, and the phone volume may be con-
trolled by the radio. OnStar operation is unaffected.
8) Connect the white 8 pin plug on the IHF-1000 cable to the
ABTI-GM4 power cable, and connect the other end of the power
cable to the ABTI-GM4 module.
CHEVROLET
Cobalt 2007
HHR 2006-07
PONTIAC
G5 2007
Solstice 2006-07
Aura 2006-07
Sky 2006-07

* IMPORTANT WARNING
THIS PRODUCT INCLUDES INSTRUCTIONS FOR INSTALLATION WHICH MUST BE
CAREFULLY FOLLOWED. THE INSTRUCTIONS ARE WORDED
IN SUCH A MANNER TO ASSUME THAT THE INSTALLER IS CAPABLE
OF COMPLETING THESE TYPE OF ELECTRONIC INSTALLATIONS.
IF YOU ARE UNCLEAR AS TO WHAT YOU ARE INSTRUCTED TO DO OR BELIEVE
THAT YOU DO NOT UNDERSTAND THE INSTRUCTIONS SO AS TO PROPERLY
AND SAFELY COMPLETE THE INSTALLATION YOU SHOULD CONSULT A TECHNI-
CIAN WHO DOES HAVE THIS KNOWLEDGE AND UNDERSTANDING. FAILURE TO
FOLLOW THESE INSTRUCTIONS
CAREFULLY AND TO INSTALL THE INTERFACE AS DESCRIBED COULD
CAUSE HARM TO THE VEHICLE OR TO SAFETY SYSTEMS ON THE VEHICLE.
INTERFERENCE WITH CERTAIN SAFETY SYSTEMS COULD CAUSE HARM TO
PERSONS AS WELL. IF YOU HAVE ANY QUESTIONS IN THIS REGARD
PLEASE CALL THE HELP LINE OR THE METRA AT 1-800-221-0932 FOR
ASSISTANCE.
21
ABTI-GM4 ABTI-GM4ABTI-GM4
INSTALLATION PROCEDURE
1) Disconnect the vehicle battery.
2) Remove the radio from the dashboard, and disconnect any
cables connected to the radio.
3) Insert the 14 pin plug on the ABTI-GM4 cable into the rear of
the radio.
4) Insert the 16 pin plug on the ABTI-GM4 cable into the rear of
the radio.
3
INSTALLATION COMPONENTS
1) ABTI-GM4 cable (Included).
2) ABTI-GM4 power cable (Included).
3) ABTI-GM4 interface (Included).
4) Motorola IHF-1000 kit (Sold separately).
5) Installation tools, wire ties, and mounting hardware as needed.
UNPLUG EXISTING
UNPLUG EXISTING
FROM CAR
FROM CAR
16 pin plug
14 pin plug
ABTI-GM4
GM LAN cable harness
8 pin
IHF-1000 keypad
plug
White
RE-PLUG EXISTING
FROM CAR
UNPLUG EXISTING
UNPLUG EXISTING
FROM CAR
16 pin plug
14 pin plug
RE-PLUG EXISTING
FROM CAR
FROM CAR
16 pin plug
14 pin plug
ABTI-GM4
GM LAN cable harness
8 pin
IHF-1000 keypad
plug
White
RE-PLUG EXISTING
FROM CAR
UNPLUG EXISTING
UNPLUG EXISTING
FROM CAR
16 pin plug
14 pin plug
RE-PLUG EXISTING
FROM CAR
FROM CAR
16 pin plug
14 pin plug