METREL Eutrotest PB User manual

EurotestPV
MI 3108
Instruction manual
Version 1.7, Code no. 20 752 095

2
Distributor:
Manufacturer:
METREL d.d.
Ljubljanska cesta 77
1354 Horjul
Slovenia
web site: http://www.metrel.si
e-mail: [email protected]
Mark on your equipment certifies that this equipment meets the requirements of the EU
(European Union) concerning safety and electromagnetic compatibility regulations
© 2013 –2017 METREL
The trade names Metrel, Smartec, Eurotest, Autosequence are trademarks registered or pending in Europe
and other countries.
No part of this publication may be reproduced or utilized in any form or by any means
without permission in writing from METREL.

MI 3108 EurotestPV Table of contents
3
Table of contents
1Preface ....................................................................................................................6
2Safety and operational considerations.................................................................7
2.1 Warnings and notes ..........................................................................................7
2.2 Battery and charging .......................................................................................12
2.3 Standards applied ...........................................................................................14
3Instrument description.........................................................................................16
3.1 Front panel......................................................................................................16
3.2 Connector panel..............................................................................................17
3.3 Back side.........................................................................................................18
3.4 Carrying the instrument...................................................................................19
3.5 Instrument set and accessories.......................................................................20
3.5.1 Standard set MI 3108............................................................................................20
3.5.2 Optional accessories.............................................................................................20
4Instrument operation............................................................................................21
4.1 Display and sound...........................................................................................21
4.1.1 Terminal voltage monitor.......................................................................................21
4.1.2 Battery indication...................................................................................................21
4.1.3 Messages..............................................................................................................21
4.1.4 Results..................................................................................................................22
4.1.5 Sound warnings.....................................................................................................22
4.1.6 Help screens.........................................................................................................22
4.1.7 Backlight and contrast adjustments.......................................................................23
4.2 Function selection ...........................................................................................23
4.3 Instruments main menu...................................................................................25
4.4 Settings ...........................................................................................................25
4.4.1 Memory.................................................................................................................26
4.4.2 Language..............................................................................................................26
4.4.3 Date and time........................................................................................................26
4.4.4 RCD standard .......................................................................................................27
4.4.5 Z factor..................................................................................................................28
4.4.6 Commander support..............................................................................................29
4.4.7 Communication .....................................................................................................29
4.4.8 Initial settings ........................................................................................................32
4.4.9 Clamp Settings......................................................................................................34
4.4.10 Synchronization (A 1378 - PV Remote unit).......................................................34
4.4.11 Solar settings.....................................................................................................36
5Measurements –a.c. LV installations.................................................................40
5.1 Compensation of test leads resistance............................................................40
5.2 Voltage, frequency and phase sequence ........................................................41
5.3 Insulation resistance........................................................................................43
5.4 Resistance of earth connection and equipotential bonding .............................45
5.5 Ring Continuity................................................................................................47
5.6 Testing RCDs..................................................................................................52
5.6.1 Contact voltage (RCD Uc).....................................................................................53
5.6.2 Trip-out time (RCDt)..............................................................................................54
5.6.3 Trip-out current (RCD I).........................................................................................54

MI 3108 EurotestPV Table of contents
4
5.6.4 RCD Autotest ........................................................................................................56
5.7 Fault loop impedance and prospective fault current........................................59
5.8 Line impedance and prospective short-circuit current / Voltage drop..............61
5.8.1 Line impedance and prospective short circuit current............................................62
5.8.2 Voltage drop..........................................................................................................63
5.9 Earth resistance ..............................................................................................65
5.10 PE test terminal...............................................................................................67
6Solar measurements - PV systems.....................................................................69
6.1 Insulation resistance on PV systems...............................................................69
6.2 PV inverter test................................................................................................71
6.3 PV panel test...................................................................................................75
6.4 Measuring of environmental parameters.........................................................77
6.2.1 Operation with A1378 PV Remote Unit ...................................................................79
6.5 Uoc / Isc test....................................................................................................79
6.6 I / V curve measurement .................................................................................81
6.7 Measurement of cell temperature before test..................................................82
7Measurements - Power & Energy........................................................................84
7.1 Power..............................................................................................................84
7.2 Harmonics.......................................................................................................85
7.3 Scope..............................................................................................................86
7.4 Current ............................................................................................................87
7.5 Energy.............................................................................................................89
8Data handling........................................................................................................90
8.1 Memory organization.......................................................................................90
8.2 Data structure..................................................................................................90
8.3 Storing test results...........................................................................................92
8.4 Recalling test results .......................................................................................93
8.5 Clearing stored data........................................................................................94
8.5.1 Clearing complete memory content.......................................................................94
8.5.2 Clearing measurement(s) in selected location and its sub-locations......................94
8.5.3 Clearing individual measurements.........................................................................95
8.5.4 Renaming installation structure elements (upload from PC) ..................................96
8.5.5 Renaming installation structure elements with serial barcode reader or RFID reader
96
8.6 Communication ...............................................................................................98
8.6.1 USB and RS232 communication...........................................................................98
Bluetooth communication..................................................................................................99
9Upgrading the instrument..................................................................................101
10 Maintenance....................................................................................................102
10.1 Fuse replacement..........................................................................................102
10.2 Cleaning........................................................................................................102
10.3 Periodic calibration........................................................................................102
10.4 Service ..........................................................................................................102
11 Technical specifications.................................................................................103
11.1 Insulation resistance (ISO L/N, ISO L/E, ISO N/E, ISO L/L), Insulation
resistance of PV systems (Roc+, Roc-)....................................................................103

MI 3108 EurotestPV Table of contents
5
11.2 Continuity & Ring (r1, r2, rN, R1+R2, R1+RN)..................................................104
11.3 RCD testing...................................................................................................104
11.3.1 General data....................................................................................................104
11.3.2 Contact voltage RCD-Uc .................................................................................105
11.3.3 Trip-out time....................................................................................................105
11.3.4 Trip-out current................................................................................................105
11.4 Fault loop impedance and prospective fault current......................................106
11.4.1 No disconnecting device or FUSE selected.....................................................106
11.4.2 RCD selected..................................................................................................107
11.5 Line impedance and prospective short-circuit current / Voltage drop............107
11.6 Resistance to earth .......................................................................................108
11.7 Voltage, frequency, and phase rotation.........................................................108
11.7.1 Phase rotation.................................................................................................108
11.7.2 Voltage............................................................................................................108
11.7.3 Frequency .......................................................................................................109
11.7.4 Online terminal voltage monitor.......................................................................109
11.8 . TRMS Clamp current...................................................................................109
11.9 Power tests....................................................................................................110
11.10 PV tests .....................................................................................................112
11.10.1 Accuracy of STC data......................................................................................112
11.10.2 Panel, Inverter.................................................................................................112
11.10.3 I-V curve..........................................................................................................113
11.10.4 Uoc - Isc..........................................................................................................113
11.10.5 Environmental parameters...............................................................................114
11.10.6 Insulation Resistance of PV systems...............................................................114
11.11 General data..............................................................................................115
Appendix A - Impedance tables................................................................................116
A.1 Impedance tables - for fuses, circuit-breakers and RCBO’s..........................116
Appendix B - Accessories for specific measurements..........................................118
Appendix C –Country notes ....................................................................................120
Appendix D –Commander (A 1401).........................................................................121
D.1 Warnings related to safety ..........................................................................121
D.2 Battery...............................................................................................................121
D.3 Description of commander.................................................................................121
D.4 Operation of commander...................................................................................122
Appendix E –PV measurements - calculated values.............................................124

MI 3108 EurotestPV Preface
6
1 Preface
Congratulations on your purchase of the Eurotest instrument and its accessories from
METREL. The instrument was designed on a basis of rich experience, acquired through
many years of dealing with electric installation test equipment.
The Eurotest instrument is a professional, multifunctional, hand-held test instrument
intended to perform all the measurements on a.c. electrical LV installations and d.c.
photovoltaic systems.
The following measurements and tests can be performed on a.c. electrical LV
installations:
Voltage and frequency,
Continuity tests,
Insulation resistance tests,
RCD testing,
Fault loop / RCD trip-lock impedance measurements,
Line impedance / Voltage drop,
Phase sequence,
Earthing resistance tests,
Current measurements,
Power, harmonics and energy measurements.
Measurements and tests on PV systems:
Voltages, currents and power in PV systems (Inverter and PV panels),
Calculation of efficiencies and STC values in PV systems,
Uoc / Isc measurements,
Environmental parameters (Temperature and Irradiance),
I-V curve test,
Insulation resistance on PV systems.
The graphic display with backlight offers easy reading of results, indications,
measurement parameters and messages. Two LED Pass/Fail indicators are placed at
the sides of the LCD.
The operation of the instrument is designed to be as simple and clear as possible and no
special training (except for the reading this instruction manual) is required in order to
begin using the instrument.
In order for operator to be familiar enough with performing measurements in general and
their typical applications it is advisable to read Metrel handbook Guide for testing and
verification of low voltage installations.
The instrument is equipped with the entire necessary accessory for comfortable testing.

MI 3108 EurotestPV Safety and operational considerations
7
2 Safety and operational considerations
2.1 Warnings and notes
In order to maintain the highest level of operator safety while carrying out various tests
and measurements, Metrel recommends keeping your Eurotest instruments in good
condition and undamaged. When using the instrument, consider the following general
warnings:
General warnings related to safety:
The symbol on the instrument means »Read the Instruction manual with
special care for safe operation«. The symbol requires an action!
If the test equipment is used in a manner not specified in this user manual,
the protection provided by the equipment could be impaired!
Read this user manual carefully, otherwise the use of the instrument may be
dangerous for the operator, the instrument or for the equipment under test!
Do not use the instrument or any of the accessories if anydamage is noticed!
Consider all generally known precautions in order to avoid risk of electric
shock while dealing with hazardous voltages!
If the 315 mA fuse blows follow the instructions in this manual in order to
replace it! Use only fuses that are specified!
Do not disassemble or repair the high breaking current fuse block! In case it
fails the entire block must be replaced with a new original one!
Do not use the instrument in AC supply systems with voltages higher than
550 Va.c.
Service, repairs or adjustment of instruments and accessories is only
allowed to be carried out by a competent authorized personnel!
Use only standard or optional test accessories supplied by your distributor!
Consider that protection category of some accessories is lower than of the
instrument. Test tips and Tip commander have removable caps. If they are
removed the protection falls to CAT II. Check markings on accessories! (cap
off, 18 mm tip)…CAT II up to 1000 V
(cap on, 4 mm tip)… CAT II 1000 V / CAT III 600 V / CAT IV 300 V
The instrument comes supplied with rechargeable Ni-MH battery cells. The
cells should only be replaced with the same type as defined on the battery
compartment label or as described in this manual. Do not use standard
alkaline battery cells while the power supply adapter is connected, otherwise
they may explode!

MI 3108 EurotestPV Safety and operational considerations
8
Hazardous voltages exist inside the instrument. Disconnect all test leads,
remove the power supply cable and switch off the instrument before
removing battery compartment cover.
Do not connect any voltage source on C1 and P/C2 inputs. They are intended
only for connection of current clamps and sensors. Maximal input voltage is
3 V!
All normal safety precautions must be taken in order to avoid risk of electric
shock while working on electrical installations!
If the instrument is not in SOLAR operating mode the instrument displays a
warning if an external DC voltage of higher than 50 V is applied to the
instrument. Measurements are blocked.
Warnings related to safety of measurement functions:
All PV functions
Use only dedicated accessories for testing on PV electrical installations.
Accessories for PV installations have yellow marked connectors.
Appropriate warnings are displayed.
PV Safety probe A1384 has inbuilt protective circuit that safely disconnects the
instrument from the PV installation in case of a failure in the instrument.
PV test lead A1385 has integrated fuses that safely disconnects instrument from
the PV installation in case of a failure in the instrument.
Do not use the instrument in PV systems with voltages higher than 1000 V
d.c. and/ or currents higher than 15 A d.c. ! Otherwise the instrument can be
damaged.
PV sources can produce very high voltages and currents. Only skilled and
trained personnel should perform measurements on photovoltaic systems.
Local regulations should be considered.
Safety precautions for working on the roof should be considered.
In case of a fault in the measuring system (wires, devices, connections,
measuring instrument, accessories), presence of flammable gases, very
high moisture or heavy dust an electrical arc can occur that will not
extinguish by itself. Arcs can lead to fire and can cause heavy damage. Users
must be skilled to disconnect the PV system safely in this case.
Insulation resistance, Insulation resistance of PV systems
Insulation resistance measurement should only be performed on de-energized
objects!
Do not touch the test object during the measurement or before it is fully discharged!
Risk of electric shock!

MI 3108 EurotestPV Safety and operational considerations
9
When an insulation resistance measurement has been performed on a capacitive
object, automatic discharge may not be done immediately! The warning message
and the actual voltage are displayed during discharge until voltage drops below
10 V.
Continuity functions
Continuity measurements should only be performed on de-energized objects!
Parallel loops may influence on test results.
Testing PE terminal
If phase voltage is detected on the tested PE terminal, stop all measurements
immediately and ensure the cause of the fault is eliminated before proceeding with
any activity!
Notes related to measurement functions:
General
The indicator means that the selected measurement cannot be performed
because of irregular conditions on input terminals.
Insulation resistance, continuity functions and earth resistance measurements can
only be performed on de-energized objects.
PASS / FAIL indication is enabled when limit is set. Apply appropriate limit value
for evaluation of measurement results.
In the case that only two of the three wires are connected to the electrical
installation under test, only voltage indication between these two wires is valid.
Insulation resistance, Insulation resistance of PV systems
Insulation resistance:
If a voltage of higher than 30 V (AC or DC) is detected between test terminals, the
insulation resistance measurement will not be performed.
Insulation resistance of PV systems:
Different pre-tests are carried out. If conditions are proper and safe the
measurement will be continued.
Otherwise or or message is displayed.
The instrument automatically discharge tested object after finished measurement.
A double click of TEST key starts a continuous measurement.
Continuity functions
If a voltage of higher than 10 V (AC or DC) is detected between test terminals, the
continuity resistance test will not be performed.
Compensate test lead resistance before performing a continuity measurement,
where necessary.
RCD functions
Parameters set in one function are also kept for other RCD functions!

MI 3108 EurotestPV Safety and operational considerations
10
The measurement of contact voltage does not normally trip an RCD. However, the
trip limit of the RCD may be exceeded as a result of leakage current flowing to the
PE protective conductor or a capacitive connection between L and PE conductors.
The RCD trip-lock sub-function (function selector switch in LOOP position) takes
longer to complete but offers much better accuracy of fault loop resistance (in
comparison to the RLsub-result in Contact voltage function).
RCD trip-out time and RCD trip-out current measurements will only be performed
if the contact voltage in the pre-test at nominal differential current is lower than the
set contact voltage limit!
The autotest sequence (RCD AUTO function) stops when trip-out time is out of
allowable time period.
Z-LOOP
The low limit prospective short-circuit current value depends on fuse type, fuse
current rating, fuse trip-out time and impedance scaling factor.
The specified accuracy of tested parameters is valid only if the mains voltage is
stable during the measurement.
Fault loop impedance measurements will trip an RCD.
The measurement of fault loop impedance using trip-lock function does not
normally trip an RCD. However, the trip limit may be exceeded if a leakage current
flows to the PE protective conductor or if there is a capacitive connection between
L and PE conductors.
Z-LINE / Voltage drop
In case of measurement of ZLine-Line with the instrument test leads PE and N
connected together the instrument will display a warning of dangerous PE voltage.
The measurement will be performed anyway.
Specified accuracy of tested parameters is valid only if mains voltage is stable
during the measurement.
Power / Harmonics / Energy / Current
Before starting any Power measurement the current clamp settings in Settings
menu should be checked. Select appropriate current clamp model and measuring
range that are best fitted to the expected current values.
Consider polarity of current clamp (arrow on test clamp should be oriented toward
connected load), otherwise result will be negative!
PV measurements
A 1384 PV Safety Probe must be used for PANEL, UOC/ISC, I/V and INVERTER
(AC, DC), and ISO PV measurements.
A 1385 PV test lead must be used for INVERTER AC/DC measurements.
Before starting a PV measurement the settings of PV module type and PV test
parameters should be checked.
Environmental parameters (Irr, T) can be measured or entered manually.
Environmental conditions (irradiance, temperature) must be stable during the
measurements.

MI 3108 EurotestPV Safety and operational considerations
11
For calculation of STC results measured Uoc / Isc values, irradiance, cell
temperature, and PV module parameters must be known. Refer to Appendix E for
more information.
Always perform zeroing of DC current clamps before test.

MI 3108 EurotestPV Safety and operational considerations
12
2.2 Battery and charging
The instrument uses six AA size alkaline or rechargeable Ni-MH battery cells. Nominal
operating time is declared for cells with nominal capacity of 2100 mAh. Battery condition
is always displayed in the lower right display part. In case the battery is too weak the
instrument indicates this as shown in figure 2.1. This indication appears for a few seconds
and then the instrument turns itself off.
Figure 2.1: Discharged battery indication
The battery is charged whenever the power supply adapter is connected to the
instrument. The power supply socket polarity is shown in figure 2.2. Internal circuit
controls charging and assures maximum battery lifetime.
+
-
Figure 2.2: Power supply socket polarity
Symbols:
Indication of battery charging
Figure 2.3: Charging indication
Warnings related to safety:
When connected to an installation, the instruments battery compartment can
contain hazardous voltage inside! When replacing battery cells or before
opening the battery/fuse compartment cover, disconnect any measuring
accessory connected to the instrument and turn off the instrument,
Ensure that the battery cells are inserted correctly otherwise the instrument will
not operate and the batteries could be discharged.
Do not recharge alkaline battery cells!
Use only power supply adapter delivered from the manufacturer or distributor of
the test equipment!
Notes:
The charger in the instrument is a pack cell charger. This means that the battery
cells are connected in series during the charging. The battery cells have to be
equivalent (same charge condition, same type and age).

MI 3108 EurotestPV Safety and operational considerations
13
If the instrument is not to be used for a long period of time, remove all batteries
from the battery compartment.
Alkaline or rechargeable Ni-MH batteries (size AA) can be used. Metrel
recommends only using rechargeable batteries with a capacity of 2100 mAh or
above.
Unpredictable chemical processes can occur during the charging of battery cells
that have been left unused for a longer period (more than 6 months). In this case
Metrel recommends to repeat the charge / discharge cycle at least 2-4 times.
If no improvement is achieved after several charge / discharge cycles, then each
battery cell should be checked (by comparing battery voltages, testing them in a
cell charger, etc). It is verylikely that only some of the battery cells are deteriorated.
One different battery cell can cause an improper behavior of the entire battery
pack!
The effects described above should not be confused with the normal decrease of
battery capacity over time. Battery also loses some capacity when it is repeatedly
charged / discharged. This information is provided in the technical specification
from battery manufacturer.

MI 3108 EurotestPV Safety and operational considerations
14
2.3 Standards applied
The Eurotest instruments are manufactured and tested in accordance with the following
regulations:
Electromagnetic compatibility (EMC)
BS EN 61326
Electrical equipment for measurement, control and laboratory
use –EMC requirements
Class B (Hand-held equipment used in controlled EM environments)
Safety (LVD)
BS EN 61010-1
Safety requirements for electrical equipment for measurement, control
and laboratory use –Part 1: General requirements
BS EN 61010-2-
030
Safety requirements for electrical equipment for measurement, control
and laboratory use –Part 2-030: Particular requirements for testing and
measuring circuits
BS EN 61010-
031
Safety requirements for electrical equipment for measurement, control
and laboratory use –Part 031: Safety requirements for hand-held probe
assemblies for electrical measurement and test
BS EN 61010-2-
032
Safety requirements for electrical equipment for measurement, control,
and laboratory use - Part 2-032: Particular requirements for hand-held
and hand-manipulated current sensors for electrical test and
measurement
Functionality
BS EN 61557
Electrical safety in low voltage distribution systems up to 1000 VAC and
1500 VAC –Equipment for testing, measuring or monitoring of protective
measures
Part 1 General requirements
Part 2 Insulation resistance
Part 3 Loop resistance
Part 4 Resistance of earth connection and equipotential
bonding
Part 5 Resistance to earth
Part 6 Residual current devices (RCDs) in TT and TN systems
Part 7 Phase sequence
Part 10 Combined measuring equipment
Part 12 Performance measuring and monitoring devices (PMD)
Reference standards for electrical installations and components
BS EN 61008
Residual current operated circuit-breakers without integral overcurrent
protection for household and similar uses
BS EN 61009
Residual current operated circuit-breakers with integral overcurrent
protection for household and similar uses
EN 60364-4-41
Electrical installations of buildings Part 4-41 Protection for safety –
protection against electric shock
BS 7671
IEE Wiring Regulations (17th edition)
AS/NZS 3017
Electrical installations –Verification guidelines
Reference standard for photovoltaic systems
BS EN 62446
Grid connected photovoltaic systems –Minimum requirements for
system documentation, commissioning tests and inspection
BS EN 61829
Photovoltaic (PV) array –On-site measurement of
current - voltage characteristics

MI 3108 EurotestPV Safety and operational considerations
15
Note about EN and IEC standards:
Text of this manual contains references to European standards. All standards of
EN 6XXXX (e.g. EN 61010) series are equivalent to IEC standards with the same
number (e.g. IEC 61010) and differ only in amended parts required by European
harmonization procedure.

MI 3108 EurotestPV Instrument description
16
3 Instrument description
3.1 Front panel
Figure 3.1: Front panel
Legend:
1
LCD
128 x 64 dots matrix display with backlight.
2
UP
Modifies selected parameter.
3
DOWN
4
TEST
TEST
Starts measurements.
Acts also as the PE touching electrode.
5
ESC
Goes one level back.
6
TAB
Selects the parameters in selected function.
7
Backlight,
Contrast
Changes backlight level and contrast.
8
ON / OFF
Switches the instrument power on or off.
The instrument automatically turns off 15 minutes after the
last key was pressed
9
HELP / CAL
Accesses help menus.
Calibrates test leads in Continuity functions.
Starts ZREF measurement in Voltage drop sub-function.
10
Function selector
- RIGHT
Selects test function.
11
Function selector
- LEFT
12
MEM
Store / recall memory of instrument.
Store clamp and solar settings.
13
Green LEDs
Red LEDs
Indicates PASS / FAIL of result.

MI 3108 EurotestPV Instrument description
17
3.2 Connector panel
Figure 3.2: Connector panel (picture of MI 3108)
Legend:
1
Test connector
Measuring inputs / outputs
2
Charger socket
3
USB connector
Communication with PC USB (1.1) port
4
Protection cover
5
C1
Current clamp measuring input #1
6
P/C2
Current clamp measuring input #2
Measuring input for external probes
7
PS/2 connector
Communication with PC serial port
Connection to optional measuring adapters
Connection to barcode /RFID reader
Connection to Bluetooth dongle
Warnings!
Maximum allowed voltage between any test terminal and ground is 600 V a.c.,
1000 V d.c.!
Maximum allowed voltage between test terminals on test connector is 600 V
a.c., 1000 V d.c.!
Maximum allowed voltage between test terminals P/C2, C1 is 3 V!
Maximum short-term voltage of external power supply adapter is 14 V!

MI 3108 EurotestPV Instrument description
18
3.3 Back side
12
3
Figure 3.3: Back panel
Legend:
1
Battery / fuse compartment cover
2
Back panel information label
3
Fixing screws for battery / fuse compartment cover
Figure 3.4: Battery and fuse compartment
Legend:
1
Fuse F1
FF 315 mA / 1000 V d.c.
(Breaking capacity: 50 kA)
2
High breaking current fuse block
4
Serial number label
5
Battery cells
Size AA, alkaline / rechargeable NiMH

MI 3108 EurotestPV: Instrument description
19
3
1
2
R: 0.0 1999 Test current: max. 8.5mA
Open-circuit voltage: 6.5V
Continuity 7mA
R: 0.18M 199.9M , U =50V ,100 ,
R: 0.12M 999M , U = 500V , 1kV
U: 0V 1200V
Nominal voltages: 100V , 250V , 500V , 1kV
Measuring current: min. 1mA at R =U 1k /V
Short-circuit current: < 3mA
N
N
N N
Insulation resistance (EN 61557-2)
V 250V
Continuity
Tripping time
non-delayed (time-delayed) RCDs
1: 0ms 300ms (500ms)
2 : 0ms 150ms (200ms)
5 : 0ms 40ms (150ms), U : 0.0V 100.0V C
Tripping current
I : 0.2 I 1.1 I AC (
t : 0ms 300ms, U : 0.0V 100.0V C
N N N 1.5 I A)
Multiplier: 0.5, 1, 2, 5
Contact voltage
U : 0.0V 100.0V
R : 0.00 10.00k (R =U / I )
C
S S C N
R : 0. 1999 I : 0. A . kAL-N(L) PSC17 20 1 4
Nominal voltage: 100V 440V/ 15Hz 500Hz
Line impedance (EN 61557-3)
Fault loop (EN 61557-3)
R : 0. 1999
I : 0. A . kA PFC 14 1 4
Nominal voltage: 100V 264V/ 15Hz 500Hz
impedance
L-PE 17
Voltage, frequency
U: 0V 440V /f: 15Hz 500Hz
Phase rotation (EN 61557-7)
Nominal voltage: 100V 440V / 1 00
Results: 1.2.3 or 2.1.3
5Hz 5 Hz
RCD (EN 61557-6)
I :10mA, 30mA, 100mA, 300mA, 500mA, 1A
Nominal voltage: 100V 264V/ 15Hz 500Hz
R Low (EN 61557-4)
R: 0.12 1999
Test current: min. ±200mA at 2
Open-circuit voltage: 6.5V 9.0V
Resistance to earth (EN 61557-5)
R: 0.04 9999
Open-circuit voltage:
Short-circuit current
< 45V
: < 20mA
RMS
Ljubljanska 77
SI - 1354 Horjul
Tel: [phone]
http://www.metrel.si
20 224 832
CAT III 600V
550V
Figure 3.5: Bottom
Legend:
1
Bottom information label
2
Neck belt openings
3
Handling side covers
3.4 Carrying the instrument
With the neck-carrying belt supplied in standard set, various possibilities of carrying the
instrument are available. Operator can choose appropriate one on basis of his operation,
see the following examples:
The instrument hangs
around operators neck
only - quick placing and
displacing.

MI 3108 EurotestPV: Instrument description
20
The instrument can be used even when placed in
soft carrying bag –test cable connected to the
instrument through the front aperture.
3.5 Instrument set and accessories
3.5.1 Standard set MI 3108
Instrument
Soft carrying bag, 2 pcs
PV Safety Probe
Monocrystal PV reference cell
PV Temperature probe
AC/ DC current clamp
Plug test cable
Test lead, 3 x 1.5 m
Test probe, 4 pcs
Crocodile clip, 4 pcs
Set of carrying straps
PV MC 4 adapter male
PV MC 4 adapter female
PV MC 3 adapter male
PV MC 3 adapter female
RS232-PS/2 cable
USB cable
Set of NiMH battery cells
Power supply adapter
CD with instruction manual, and “Guide for testing and verification of low voltage
installations” handbook.
Short instruction manual
Calibration Certificate
3.5.2 Optional accessories
See the attached sheetfor a list of optional accessories that are available on request from
your distributor.