Meyra 1 612 iCHAIR MC3 27 Use and care manual

en
Assembly and user manual
Dahl Docking Locking set
Model: 1.612 iCHAIR MC3;
Code 27, Code 352
MEANING OF THE AP-
PLIED MARKERS
Safety instructions with a coloured back-
ground are mandatory and need to be
observed under any circumstance!
☞This symbol indicates tips and recom-
mendations
[ ] Reference to a picture number
( ) Reference to a function element within
a picture.
INTRODUCTION
Read and observe this manual before
first operation. Children and adolescents
should read this document if necessary
together with their parents or a supervisor
or accompanying person before first use.
The user manual at hand should help you
get accustomed to the handling of your
product.
This product is a technical aid. It is subject to
explanations, requires regular care and can
cause danger when used improperly. The
correct handling must therefore be learned.
Users with visual impairments can find the
PDF-files together with further information
on our website:
< www.meyra.com >.
☞Contact your specialist dealer when re-
quired.
Information about product safety and pos-
sible recalls of our products can be found in
the < Information center > on our website:
< www.meyra.com >.
The product meets the demands of ISO
7176-19.

1
234
5
8
6
7
2
LIST OF MODELS
This assembly and user manual is valid for
the following model options:
Model 1.612 - 352
Model 1.612 - 27
USE
The Dahl Engineering docking anchoring
set is solely to be used together with a
Dahl Engineering anchoring unit mount-
ed expertly into a motor vehicle < www.
dahlengineering.dk >.
This product serves for automatic fixation of
the wheelchair during the transport of peo-
ple inside a motor vehicle in combination
with the Dahl Engineering docking anchor-
ing set.
ASSEMBLY INSTRUCTIONS
Scope of delivery
Docking anchoring set:
Scope of delivery Dahl
(as component of the attachment inside the
motor vehicle)
(1) 1x Locking plate
(2) 1x Distancer
(3) 3x Countersunk screw
(4) 2x Countersunk screw long
Scope of delivery Meyra
(5) 6x Countersunk screw M8 x 25
(6) 1x Attachment plate (only on Code 352,
without Lift)
(7) 1x Adapter plate
(8) 1x Clamping block
– 1x Assembly and user manual

6
a
8
75
5
8
7
5
3
ASSEMBLY
The following assembly is to be carried
out by a professionally qualified person.
Detailed information to the assembly tips
of the Dahl Docking-Station inside the
motor vehicle can be obtained per e-mail
at: < [e-mail] >.
Safety information
The electric wheelchair is to be switched
off during assembly in order to prevent
unintentional rolling movements.
Before assembly the main-/battery fuse is
to be removed.
Watch for jamming areas during the com-
plete assembly. – Danger of jamming!
Keep the working area clean during the
assembly!
Code 352, without Lift
Mounting the adapter plate
1. To mount the adapter plate (7), insert
the attachment plate (6) into the profile
tube (a).
2. Screw the adapter plate (7) and the
attachment plate (6) together with 4x
countersunk screw (5).
3. Place the clamping block (8) onto the
adapter plate (7) and tighten with 2x
countersunk screw (5).

8
7
5
2
1
4
3
4
Code 27, with Lift
Mounting the adapter plate
1. Screw the adapter plate (7) with 4x
countersunk screws (5) underneath the
base of the lifting cylinder.
2. Place the clamping block (8) onto the
adapter plate (7) and tighten with 2x
countersunk screw (5).
Mounting the docking set
For a correct ground clearance of 70 mm,
assembly is to be carried out incl. the load
of the actual user weight.
A corresponding distancer (2) has to be
orderedBei Bedarf ist über< www.dahl-
engineering.dk >.
For safety reasons only use the includ-
ed special countersunk screws (quality
grade 14.9, Torx 27) (3)+(4).
Secure the countersunk screws with Loc-
tite 222.
Observe torque 16 - 18 Nm!
1. Screw the countersunk screws, facing
forward in driving direction (3) with the
locking plate (1) and distancer (2) slid
onto it from the bottom into the adapt-
er plate (7).
2. Screw the two long countersunk screws
(4) from the bottom into the clamping
block (8).
3. Check and ensure the firm seat of the
docking set in combination with the as-
sembly inside the motor vehicle.
Re-establish driving readiness
1. Swivel the seat unit down.
2. Insert the battery fuse.

1
5
USER MANUAL
Safety information
When using the wheelchair watch for
the reduced ground clearance due to the
mounted docking set. – Danger of acci-
dents!
☞Therefore observe chapter Technical
data on page 8.
For handicapped transport inside a motor
vehicle observe the document < Safety
with Meyra-wheelchairs, also during trans-
port in motor vehicles >.
Only drive wheelchairs equipped with
the docking set into Dahl Engineering an-
choring units [1].
Before use make sure that the product is
functional. – Danger of accidents!
Do not use a loose locking plate to anchor
the wheelchair. – Increased danger of ac-
cident!
Correct anchoring of the wheelchair with
the docking-station only happens with
the weight of the user.
The user must be secured with a certified
strap-retaining system.
MEYRA doe not claim responsibility for
damages that are caused by unattended
minors in combination with the product!

2
1
6
Anchoring the wheelchair
If the wheelchair is anchored correctly, a
control diode ill light up on the operating
module (1) of the docking station.
Further information to the Dahl Docking
Station can be found on the website:
< www.dahlengineering.dk >.
To lock the docking station, move the
wheelchair straight and centred over the
anchoring unit (2) on the floor of the motor
vehicle.
☞If the wheelchair is not anchored cor-
rectly, a warning signal sounds and a
warning light appears on the operating
module (1) of the docking station.
☞If necessary observe the operating
manual of the Dahl-Dockingstation.
Unlocking the wheelchair
To unlock the wheelchair, press the release
key on the operating module (1) of the
docking station and then move the wheel-
chair slowly backwards out of the anchoring
unit (2) on the floor of the motor vehicle.
☞The procedure e.g. in case of a break-
down of the battery of the motor ve-
hicle can be viewed in the operating
manual of your Dahl-Dockingstation.
Repairs
Use only original spare parts. Make use of
the service of your educated dealer.
DISPOSAL
The disposal must comply with the respec-
tive national law.
Please enquire about local disposal arrange-
ments at your municipal authority.

7
MAINTENANCE
An incorrect or neglected cleaning and
maintenance of the product results in a lim-
itation of the product liability.
Maintenance
The following maintenance Instruction
gives you a guide for carrying out the main-
tenance work.
☞They do not give information about the
actual extent of work required on the
product.

8
WHEN WHAT REMARK
After use Check for extreme soil-
ing
Clean if required
Carry out the cleaning by
yourself or by an aid.
Every 6 months
(depending on frequency
of use)
Check screwed con-
nections for firm seat.
Carry out the test yourself
or by a helper.
Manufacturer recom-
mendation:
Every 12 months
(depending on frequency
of use)
Safety inspection To be carried out by the
specialist dealer.
TECHNICAL DATA
Docking-Station
Perm. user weight
(including additional load)
136 kg
Ground clearance 40 mm
A higher user weight indicated on the
type plate of your wheelchair is limited by
the permitted user weight of the docking
station.
Maintenance schedule
WARRANTY / GUARANTEE
We accept legal liability for this product
within the scope of or general terms and
conditions and warranty and in certain cas-
es other verbal resp. agreed upon guaran-
tees.
☞Therefore observe chapter < Warranty /
Guarantee > of the operating manual of
your wheelchair.

9
NOTES

10
NOTES

11
NOTES

MEYRA GmbH
Meyra-Ring 2
32689 Kalletal Kalldorf
GERMANY
Tel [phone] - 311
Fax [phone] - 9311
[email protected]
www.meyra.de
This product is conform with the EC-direc-
tive 93/42/EEC (MDD) and fulfils up from
25th May 2021 the valid requirements of the
regulation (EU) 2017/745 for medical devic-
es.
205 345 801 (Status: 2021-04) All technical modifications reserved.