MF DIGITAL DIRECTOR series User manual

DIRECTOR/DIRECTOR PRO
Series
Disc Publishing System
User Manual

MF Digital Director/Director Pro Series Publishing System User Manual Revised July 2010
Page 2
Welcome to the Director/Director Pro System
Copyright Notice
Copyright ©2003, 2004, 2005, 2006 & 2010 by MF DIGITAL (All rights reserved)
This manual and the accompanying illustrations may not be copied, reproduced,
electronically transmitted, or translated into another language, in whole, or in part,
without the written consent of MF DIGITAL.
MF DIGITAL, Director & Director Pro are trademarks of MF DIGITAL.
Other trademarks referred to are the property of their respective trademark or
registered trademark holders.
Blu-ray / DVD-R/RW Recorder Warranty Policy
Individual Blu-ray and DVD-R/RW recorder manufacturers are responsible for the products they provide. As a
convenience, MF DIGITAL will honor any service issue related to a defective recorder while under its
respective manufacturer’s warranty providing that the recorder has been purchased from MF DIGITAL either
directly or indirectly. MF DIGITAL assumes no responsibility for products NOT purchased through MF
DIGITAL.
Piracy
The copying of audio, video, or software without the permission of the copyright holder is illegal. MF DIGITAL
accepts no responsibility for the copyright use or misuse of this equipment. It is the sole responsibility of the
user to ensure that the legal rights of copyright in duplicating are respected.
Corporate Headquarters:
MF Digital
155 Sherwood Avenue
E. Farmingdale, NY 11735
phone: [phone]
fax: [phone]
e-mail: [email protected]
website: http://www.mfdigital.com/

MF Digital Director/Director Pro Series Publishing System User Manual Revised July 2010
Page 3
About MF Digital
Thank you for purchasing MF Digital’s DIRECTOR/DIRECTOR PRO
publishing system. MF Digital manufactures a wide variety of software and
audio duplication and production equipment, including manual and fully
automatic Disc duplicators and printers. We hope you will consider us for
all of your production needs.
What To Expect From Your MF Digital DIRECTOR/DIRECTOR
PRO Publishing System
The MF Digital DIRECTOR/DIRECTOR PRO publishing system is
professionally designed and manufactured to give you years of trouble free
operation. To avoid accidental damage to your new
DIRECTOR/DIRECTOR PRO publishing system, please read and
understand this manual thoroughly before operating the unit.
About This Manual
This manual is written for both novice and experienced users. Please read
through this Operator’s Guide from beginning to end before using the unit.
Once having read the manual, follow along chapter by chapter. This will
provide the necessary understanding of your new DIRECTOR/DIRECTOR
PRO publishing system.

MF Digital Director/Director Pro Series Publishing System User Manual Revised July 2010
Page 4
WELCOME TO THE DIRECTOR/DIRECTOR PRO SYSTEM ..........................................................................2
C OPYRIGHT N OTICE ....................................................................................................................................................2
B LU - RAY / DVD-R/RW R ECORDER W ARRANTY P OLICY ...........................................................................................2
P IRACY .......................................................................................................................................................................2
C ORPORATE H EADQUARTERS :....................................................................................................................................2
ABOUT MF DIGITAL................................................................................................................................................3
W HAT T O E XPECT F ROM Y OUR MF D IGITAL DIRECTOR/DIRECTOR PRO P UBLISHING S YSTEM .........................3
ABOUT THIS MANUAL............................................................................................................................................3
INSTALLING THE DIRECTOR/DIRECTOR PRO...............................................................................................7
W HAT ’ S IN THE B OX ...................................................................................................................................................7
P ACKING M ATERIALS .................................................................................................................................................7
T HE B EST P LACE TO P UT THE DIRECTOR/DIRECTOR PRO...................................................................................7
S AFETY P RECAUTIONS ................................................................................................................................................7
LOCATION OF DIRECTOR/DIRECTOR PRO COMPONENTS .......................................................................9
F RONT V IEW .......................................................................................................................................................9
R EAR V IEW .................................................................................................................................................................9
REMOVING PACKING RESTRAINTS ................................................................................................................10
INPUT AND OUTPUT SPINDLES .........................................................................................................................10
INSTALLING THE MONITOR, KEYBOARD AND MOUSE ............................................................................ 11
C ONNECTING T HE M ONITOR ....................................................................................................................................11
C ONNECTING T HE M OUSE A ND K EYBOARD .............................................................................................................11
INSTALLING THE NETWORK CABLE ..............................................................................................................11
C ONNECTING THE N ETWORK C ABLE ........................................................................................................................12
STARTING THE DIRECTOR/DIRECTOR PRO FOR THE FIRST TIME ......................................................13
P OWER C ONNECTION AND S ETTINGS ........................................................................................................................13
APPLICATION STARTUP......................................................................................................................................14
S TARTING THE DIRECTOR/DIRECTOR PRO A PPLICATION ..................................................................................14
DIRECTOR/DIRECTOR PRO A PPLICATION L AYOUT ............................................................................................14
DIRECTOR/DIRECTOR PRO A PPLICATION C ONFIGURATION ...............................................................................15
P RINTER D RIVER (R EQUIRED ) ..................................................................................................................................16
O PERATOR ’ S E MAIL A DDRESS (O PTIONAL ) ..............................................................................................................16
R ECORDING S PEED (R EQUIRED ) ...............................................................................................................................16
A SYNCHRONOUS M ODE (R EQUIRED )........................................................................................................................17
D ESCRIPTION ............................................................................................................................................................17
D ISABLED .................................................................................................................................................................17
J OBS =S YNCHRONOUS (FIFO), D RIVES =S YNCHRONOUS ..........................................................................................17
L EVEL 0....................................................................................................................................................................17
L EVEL 1*..................................................................................................................................................................18
L EVEL 2*..................................................................................................................................................................18
J OBS =A SYNCHRONOUS (FIFO), D RIVES =A SYNCHRONOUS ......................................................................................18

MF Digital Director/Director Pro Series Publishing System User Manual Revised July 2010
Page 5
D
EFAULT J OB F ILE F OLDER (R EQUIRED ) ..................................................................................................................18
D EFAULT I MAGE F ILE F OLDER (R EQUIRED )..............................................................................................................19
D EFAULT L ABEL F ILE F OLDER (R EQUIRED )..............................................................................................................19
C REATING N EW P RIVILEGES P ROFILE .......................................................................................................................19
E DITING E XISTING P RIVILEGES P ROFILE ...................................................................................................................21
D ELETING E XISTING P RIVILEGES P ROFILE ................................................................................................................22
C REATING N EW U SERS .............................................................................................................................................22
E DITING E XISTING U SERS .........................................................................................................................................23
D ELETING E XISTING U SERS ......................................................................................................................................23
D EFAULT J OB O PTIONS .............................................................................................................................................23
S YSTEM D RIVES .......................................................................................................................................................25
C ONTROLLING THE DIRECTOR/DIRECTOR PRO F ROM C USTOM A PPLICATIONS .................................................25
CREATING DISC LABELS.....................................................................................................................................27
L ABEL E DITOR M ENU B AR .......................................................................................................................................27
C REATING T EXT .......................................................................................................................................................28
C HANGING T EXT AND T EXT A TTRIBUTES .................................................................................................................29
I MPORTING G RAPHICS ..............................................................................................................................................29
R ESIZING G RAPHICS .................................................................................................................................................30
R EPOSITIONING T EXT , G RAPHICS AND D ATES ..........................................................................................................31
C ENTERING T EXT AND G RAPHICS .............................................................................................................................31
S AVING THE C URRENT D ISC L ABEL ..........................................................................................................................32
O PENING E XISTING D ISC L ABELS .............................................................................................................................33
UTILIZING .PDF FILES FOR PRINTING (COMMAND MODULE CLIENT ONLY) ..................................34
UTILIZING .PDF FILES FOR PRINTING – CON’T (COMMAND MODULE CLIENT ONLY)..................35
CREATING DISC IMAGES ....................................................................................................................................36
D ATA D ISC I MAGES ..................................................................................................................................................36
D ATA I MAGE E DITOR T OOLBAR ...............................................................................................................................37
S TATIC AND D YNAMIC C ONTENT ..............................................................................................................................38
A DDING F ILES AND F OLDERS ....................................................................................................................................38
R EMOVING F ILES AND F OLDERS ...............................................................................................................................38
C REATING N EW F OLDERS .........................................................................................................................................38
N AMING A F OLDER ...................................................................................................................................................39
S AVING THE C URRENT D ISC I MAGE F ILE ..................................................................................................................40
L OADING AN E XISTING S CRIPT F ILE ..........................................................................................................................43
A UDIO D ISC I MAGES .................................................................................................................................................43
A UDIO I MAGE T OOLBAR ...........................................................................................................................................44
A DDING T RACKS ......................................................................................................................................................45
S ELECTING DISC C APACITY .......................................................................................................................................45
R EMOVING T RACKS ..................................................................................................................................................46
E DITING A T RACK .....................................................................................................................................................46
C HANGING ISRC C ODES AND C OPY P ROHIBIT F LAGS ..............................................................................................46
I NSERTING , E DITING AND R EMOVING S ILENCE .........................................................................................................47
I NSERTING , E DITING AND R EMOVING S UB - INDEXES .................................................................................................48
S AVING THE C URRENT A UDIO D ISC I MAGE ..............................................................................................................49
L OADING AN E XISTING A UDIO D ISC I MAGE ..............................................................................................................50
CREATING JOBS.....................................................................................................................................................51
C REATING N EW J OBS ................................................................................................................................................51
J OB M ENU B AR ........................................................................................................................................................52
G ENERAL O PTIONS ...................................................................................................................................................52
J OB ID (R EQUIRED ) ..................................................................................................................................................53
U SER ID (R EQUIRED ) ...............................................................................................................................................53
P ASSWORD (R EQUIRED ) ...........................................................................................................................................53

MF Digital Director/Director Pro Series Publishing System User Manual Revised July 2010
Page 6
I
MAGE ( NEEDED IF “C OPY ” OPTION IS CHECKED )......................................................................................................54
L ABEL F ILE (O PTIONAL ) ...........................................................................................................................................54
C OMMENTS (O PTIONAL )...........................................................................................................................................56
Q UANTITY (R EQUIRED ) ............................................................................................................................................56
P RIORITY (R EQUIRED ) ..............................................................................................................................................56
S AVING THE C URRENT J OB .......................................................................................................................................56
L OADING AN E XISTING J OB .......................................................................................................................................57
SUBMITTING JOBS ................................................................................................................................................58
S UBMITTING A J OB ...................................................................................................................................................58
T HE P RODUCTION P ROCESS ......................................................................................................................................59
R EMOVING A J OB ......................................................................................................................................................60
C LEARING THE C OMPLETED J OBS L IST .....................................................................................................................60
S TARTING A N EW J OB ...............................................................................................................................................60
A BORTING A J OB ......................................................................................................................................................60
VIEWING LOGS.......................................................................................................................................................61
VIEWING THE ERRORS REPORTED BY DIRECTOR IN THE EVENT VIEWER. ....................................62
U PDATING J OB R ECORDS ..........................................................................................................................................64
N AVIGATING J OB R ECORDS ......................................................................................................................................64
D ELETING A LL J OB R ECORDS ...................................................................................................................................64
R ESUBMITTING J OBS .................................................................................................................................................64
DUPLICATING EXISTING DISCS ........................................................................................................................65
C REATING AN I MAGE F ILE ........................................................................................................................................65
VIEWING RESOURCES .........................................................................................................................................68
UPGRADING DIRECTOR/DIRECTOR PRO SOFTWARE ...............................................................................69
O VERVIEW OF THE PROCESS .....................................................................................................................................69

MF Digital Director/Director Pro Series Publishing System User Manual Revised July 2010
Page 7
Installing the DIRECTOR/DIRECTOR PRO
Carefully remove the DIRECTOR/DIRECTOR PRO publishing system
from the shipping container. Inspect the contents and verify them against
the packing slip. Report any errors in shipping as soon as possible.
What’s in the Box
Your DIRECTOR/DIRECTOR PRO is a complete publishing system
containing all necessary components. The package includes:
•DIRECTOR/DIRECTOR PRO publishing system (either CD/DVD, or
CD/DVD/Blu-ray)
•Power cords
•Operator’s Guide (on CD/DVD)
•Windows license pack
•MF Digital Product & Warranty Registration card
•Printer (see Setup Guide for printer setup)
To obtain optional Director Client software (DClient) software visit
www.mfdigital.com/techsupport.html
Packing Materials
Please retain the original box and packaging in the event that the unit
requires future servicing. This will help to reduce the possibility of damage
occurring in transit.
The Best Place to Put the DIRECTOR/DIRECTOR PRO
The best operating location for the DIRECTOR/DIRECTOR PRO
publishing system is in a climate controlled area, free of dirt, dust, humidity,
excessive heat, and electronic or electromagnetic interference. Room
temperature should be between 65 and 75 degrees Fahrenheit, or between
18 and 23 degrees Celsius. Place the DIRECTOR/DIRECTOR PRO on a
solid, steady work surface and allow sufficient room for all incidental work
materials. Provide at least six inches of clearance on all sides of the unit for
ventilation.
Safety Precautions
The system is shipped with a three-prong power connector and must be
used with a properly grounded AC receptacle. DO NOT try to defeat the

MF Digital Director/Director Pro Series Publishing System User Manual Revised July 2010
Page 8
third “ground” prong. All computer peripherals must be properly grounded
and the DIRECTOR/DIRECTOR PRO is no exception. The use of a power
conditioner such as an Uninterruptible Power Supply (UPS), or a surge
protector is highly recommended. At the very least you should consider
connecting the PC portion of the DIRECTOR/DIRECTOR PRO to a UPS.
The minimum required size is 500VA.
Repairs or alterations should only be attempted by authorized factory
trained technicians. MF Digital reserves the right to void the warranty if
unauthorized service is performed.

MF Digital Director/Director Pro Series Publishing System User Manual Revised July 2010
Page 9
Location Of DIRECTOR/DIRECTOR PRO Components
Front View
Rear View
Loading Arm
Reject Area
Input #1
Input #2
Output Spindle
Mouse
Keyboard
Monitor
Network
System
On/Off
Switch
Power
Cord
Power
On/Off
Switch

MF Digital Director/Director Pro Series Publishing System User Manual Revised July 2010
Page 10
Removing Packing Restraints
The DIRECTOR/DIRECTOR PRO ships with a picker arm restraint to
reduce the possibility of damage in transit. This restraint must be removed
before operation or power-on. Remove the foam block above the transfer
arm. Save the foam block, as you will need to return it to its place if you
need to transport the unit in the future.
Input and Output Spindles
The input bin and the output spindle and bins serve as the containers to
store up to 150 blank and recorded discs per bin.
NOTE: See section entitled, Loader Options when activating separate
CD/DVD spindles.

MF Digital Director/Director Pro Series Publishing System User Manual Revised July 2010
Page 11
Installing The Monitor, Keyboard And Mouse
Before operating the DIRECTOR/DIRECTOR PRO, the user supplied
monitor, keyboard and mouse must be attached.
Connecting The Monitor
•Place the monitor on either side of the DIRECTOR/DIRECTOR PRO
unit.
•Make sure the monitor power switch is set to the off position.
•Connect one end of the power cord to the VAC Out on the monitor and
the other to the wall power outlet.
•Connect the DB15 male connector of the video cable to the High
Density DB15 female Video In port on the back of the host computer.
Connecting The Mouse And Keyboard
•Connect the PS/2 male connector of the mouse cord to the PS/2 female
Mouse In port on the back of the DIRECTOR/DIRECTOR PRO. If
using USB, then connect to one of the free USB ports on the rear of the
unit. Keep in mind you may need a free USB port for your printer.
•Connect the PS/2 male connector of the keyboard cord to the PS/2
female Keyboard In port on the back of the DIRECTOR/DIRECTOR
PRO. If using USB, then connect to one of the free USB ports on the
rear of the unit. Keep in mind you may need a free USB port for your
printer.
Installing The Network Cable
In addition to operating as a standalone duplicator the
DIRECTOR/DIRECTOR PRO can be connected to a network to receive
files for pre-mastering or even be remotely controlled by use of the
DIRECTOR/DIRECTOR PRO’s Network Client Software, or your own
application by way of the Director’s advanced Application Program
Interface (SmartAPI). The unit comes equipped from the factory with
onboard gigabit LAN port for network attachment.
While networks are commonplace, their connection and interconnection
require specific expertise far beyond the scope of this manual. For our
purposes here, we will assume you either have expertise with networking
computers, or had your unit professionally installed by MF Digital.
Note:

MF Digital Director/Director Pro Series Publishing System User Manual Revised July 2010
Page 12
Connecting the Network Cable
Connect a suitable patch cord to the RJ45 network port on the back of the
DIRECTOR/DIRECTOR PRO unit. A Category 3 or better cable should be
used for 10Base-T, Category 5 for 100Base-T network connection, and
category 5E or 6 for 1000Base-T (Gigabit)

MF Digital Director/Director Pro Series Publishing System User Manual Revised July 2010
Page 13
Starting the DIRECTOR/DIRECTOR PRO For the First Time
Before Disc creation or duplication can begin it is necessary to review a few
details.
Power Connection and Settings
•Make sure the DIRECTOR/DIRECTOR PRO power switch is set to the
off position or “0”.
•The unit has an auto switching power supply that supports 100 – 240V
AC.
•Plug one end of the supplied power cord into the receptacle at the rear of
the unit and the other end into the wall or UPS power outlet.

CAUTION
Always use properly grounded receptacles, or severe damage to
your system may result. The use of a surge protector or
Uninterruptible Power Supply (UPS) is highly recommended.
Starting Up
•Flip the DIRECTOR/DIRECTOR PRO power switch to the “on”
position.
•Switch on the power to the printer.
•Wait a minute or two while the system starts up. A series of diagnostic
information will be displayed and once complete the unit will display
the Windows desktop.
The DIRECTOR/DIRECTOR PRO uses Microsoft’s Windows For the
operating system. To get the most out of the DIRECTOR/DIRECTOR
PRO it is recommended that users supplement this manual with a
Windows guide.
Note:

MF Digital Director/Director Pro Series Publishing System User Manual Revised July 2010
Page 14
Application Startup
The DIRECTOR/DIRECTOR PRO is a state-of-the-art disc publishing
system and duplicator. It is designed to create, duplicate, print and verify
most standard disc formats. This startup section will guide you through
starting and configuring the DIRECTOR/DIRECTOR PRO application.
Starting the DIRECTOR/DIRECTOR PRO Application
To start the DIRECTOR/DIRECTOR PRO application the steps are as
follows:
•From the DIRECTOR/DIRECTOR PRO desktop, double click the
“DIRECTOR/DIRECTOR PRO” icon on the Windows desktop. The
DIRECTOR/DIRECTOR PRO application screen will now be
displayed:
•Place as many blank discs as required onto the input spindle.
DIRECTOR/DIRECTOR PRO Application Layout
The DIRECTOR/DIRECTOR PRO application is organized into a sequence
of eight pages accessible by tabs at the top of the screen (System Status,
Create Job, Data Image Editor, Audio Image Editor, Label Editor,
Resources Info, System Setup, System Log). By completing information on
these cards you control the actions of the DIRECTOR/DIRECTOR PRO to
create, duplicate and verify discs as well as print discs labels.

MF Digital Director/Director Pro Series Publishing System User Manual Revised July 2010
Page 15
Tabs:
System Status Displays the status of jobs after they have been
submitted for production.
Create Job Brings together the data or audio contents and label
components of a disc so it can be produced.
Data Image
Editor
Specifies the contents of a data disc to be recorded.
Audio Image
Editor
Specifies the contents of an audio disc to be recorded.
Label Editor Creates labels to be printed on the surface of discs.
Resources Info Displays the hardware elements connected to the
DIRECTOR/DIRECTOR PRO.
System Setup Defines operating settings and user privileges.
System Log Displays the database of information maintained on all
jobs.
DIRECTOR/DIRECTOR PRO Application Configuration
Before creating or duplicating a disc the DIRECTOR/DIRECTOR PRO
application must first be configured. The System Setup tab is used to
establish a number of important settings including basic operation
parameters as well as the authorized users and privileges they have using
the DIRECTOR/DIRECTOR PRO.
To begin or modify an existing setup of the DIRECTOR/DIRECTOR PRO:
•Click the System Setup tab. The screen will now display:
Note:
Apply button must be clicked in order for any changes to take effect, except
for modification of users and privileges.

MF Digital Director/Director Pro Series Publishing System User Manual Revised July 2010
Page 16
The System Setup tab is divided into a number of information fields that
must be completed.
Printer Driver (Required)
The Printer Driver pull-down is used to indicate to the
DIRECTOR/DIRECTOR PRO the type of printer that is installed.
•Click the Printer Driver pull down and select your printer.
Operator’s Email Address (Optional)
The OPERATOR’S EMAIL ADDRESS field is a user defined email
address to which a network attached DIRECTOR/DIRECTOR PRO will
send a message when the unit requires attention (such as an empty input
spindle, etc.). The email feature requires the presence of a POP3 or IMAP
server on the network and that an email client account be created for use by
the DIRECTOR/DIRECTOR PRO.
•Click the Operator’s E-mail Address field and enter an email address.
Leave the field blank if the DIRECTOR/DIRECTOR PRO is not
attached to a network or if you do not want to receive unit attention
messages.
Recording Speed (Required)
The Recording Speed pull-down allows you to set the recording speed as
determined by the capabilities of the recorders installed in the
DIRECTOR/DIRECTOR PRO.
•Click the Recording Speed pull down either for CD, DVD, or Blu-ray (if
equipped) and select the desired recording speed.
•Click Apply to activate the changes.
For CD: “4x, 8x, 12x, 16x, 20x, 24x, 40x,” or “maximum speed”
For DVD: “6x, 8x, 12x” or “maximum speed”
DIRECTOR/DIRECTOR PRO sends email via MAPI hence you must
first setup a MAPI email client on the DIRECTOR/DIRECTOR PRO.
Make sure you set this client to be used from MAPI based applications.
Note:
Note:

MF Digital Director/Director Pro Series Publishing System User Manual Revised July 2010
Page 17
Asynchronous Mode (Required)
The Asynchronous Mode pull-down is used to instruct the
DIRECTOR/DIRECTOR PRO how to process jobs. This affects both how
jobs are handled and how the drives operate. Jobs and drives can run either
synchronously or asynchronously. In the table below you will find each
mode detailed. Let’s define the basic modes first:
Jobs=Synchronous / Asynchronous
When jobs are Synchronous, they are completed in the order in which
they were submitted. Take for example two jobs submitted for one copy
each. The first job is of a 650MB master while the second job is only
10MB. While the second job submitted will be completed prior to the
first job, it will not be outputted to the accept spindle until the second
job has been completed. When jobs are Asynchronous they will be
outputted to the accept spindle as they are completed.
Drives=Synchronous /Asynchronous
Drives can also run either synchronously or asynchronously. In
synchronous mode, all the drives in use for a given job, run in tandem or
parallel to one another. In asynchronous mode, all the drives in use for a
given job, operate independently of each other. For example if you
submit a job for three copies and the drives are operating synchronously,
the copying process will not begin until all drives become ready. On the
other hand, if the same job were submitted with the drives operating
asynchronously, each drive would begin to write as soon as it becomes
ready, independently of any other drives which may also be in use for
this particular job. Asynchronous mode is more demanding of system
resources.
The modes of operation are:
Mode Description
Disabled Jobs=Synchronous (FIFO), Drives=Synchronous
When the setting is “disabled”, jobs are processed on a first in/first out
(FIFO) basis such that they will be kept together when placed on the
output spindle. For example, let us say two jobs of one piece each are
submitted. Job 1 is a 650 MB disc and Job 2 is a 10 MB disc. Even
though Job 2 was submitted last, it will completed before Job 1 but it will
NOT be outputted to the accept spindle until Job 1 is done.
Level 0 Jobs=Asynchronous, Drives=Synchronous (Default)
When the setting is “level 0” jobs are still started on a first in / first out
basis, but completed jobs
will be outputted when they are done and

MF Digital Director/Director Pro Series Publishing System User Manual Revised July 2010
Page 18
therefore discs will be mixed together on the output spindle. For
example, let us say two jobs of two pieces each are submitted. Job 1 is a
650 MB
disc and Job 2 is a 10 MB disc. Even though Job 2 was submitted last, it
will completed before Job 1 but unlike the DIASBLED mode, it will not
be held but rather immediately outputted to the accept spindle when it is
done. In processing the respective jobs, the two drives in use for each job
will function in tandem such that they will not begin to write until both
drives have become ready.
Level 1* Jobs=Synchronous (FIFO), Drives=Asynchronous
When the setting is “Level 1”, jobs are processed on a first in/first out
(FIFO) basis such that they will be kept together when placed on the
output spindle. For example, let us say two jobs of two pieces each are
submitted. Job 1 is a 650 MB disc and Job 2 is a 10 MB disc. Even
though Job 2 was submitted last, it will completed before Job 1 but it will
NOT be outputted to the accept spindle until Job 1 is done. In processing
the respective jobs, the two drives in use for each job will function
independently of one another and begin to write as soon as they become
ready.
Level 2* Jobs=Asynchronous (FIFO), Drives=Asynchronous
When the setting is “level 2” jobs are still started on a first in / first out
basis but completed jobs will be outputted when they are done. For
example, let us say two jobs of two pieces each are submitted. Job 1 is a
650 MB disc and Job 2 is a 10 MB disc. Even though Job 2 was
submitted last, it will completed before Job 1 but unlike the DIASBLED
mode, it will not be held but rather immediately outputted to the accept
spindle when it is done. In processing the respective jobs, the two drives
in use for each job will function independently of one another and begin
to write as soon as they become ready. In this mode, disc placement on
output spindle will be scattered.
•Click the ASYNCHRONOUS MODE pull down and select the desired
“disabled” or “level O” setting (level 1 and level 2 not used).
Default Job File Folder (Required)
The DEFAULT JOB FILE FOLDER field is used to specify the default
location where job files (*.JOB) will be saved. The factory setting
(C:\discDIRECTOR\Jobs\) should be sufficient for most uses. To change
the default setting:
•Click the Browse button below the DEFAULT JOB FILE FOLDER
field.
•Select the volume and DIRECTOR/DIRECTOR PRO where you wish to
save job files.
•Click the OK button.

MF Digital Director/Director Pro Series Publishing System User Manual Revised July 2010
Page 19
Default Image File Folder (Required)
The DEFAULT IMAGE FILE FOLDER field is used to specify the default
location where disc image script (*.ISC) will be saved. The factory setting
(C:\discDIRECTOR\Images\) should be sufficient for most uses. To change
the default setting:
•Click the Browse button below the DEFAULT IMAGE FILE FOLDER
field.
•Select the volume and DIRECTOR/DIRECTOR PRO where you wish to
save disc image files.
•Click the OK button.
Default Label File Folder (Required)
The DEFAULT LABEL FILE FOLDER field is used to specify the default
location where disc label files (*.LBL) will be saved. The factory setting
(C:\discDIRECTOR\Labels\) should be sufficient for most uses. To change
the default setting:
•Click the Browse button below the DEFAULT LABEL FILE FOLDER
field.
•Select the volume and DIRECTOR/DIRECTOR PRO where you wish to
save disc label files.
•Click the OK button.
Loader Options
Shake Disc – By selecting Shake Disc the loader arm will shake the disc
after picking to prevent multiple discs being lifted at the same time.
Though, you should always separate the media as you load to the unit as this
helps prevent discs from sticking together as well.
Spindle Select – By selecting this option the left and right spindles are
separated respectively to DVD and CD. NOTE: Keep in mind, when
selecting this option; you only load 75 Discs in each hopper. As the output
hopper is now shared.
Creating New Privileges Profile
Control access to the DIRECTOR/DIRECTOR PRO by restricting use to
only authorized users. The main intent of this is for jobs submitted remotely

MF Digital Director/Director Pro Series Publishing System User Manual Revised July 2010
Page 20
through the included Network Client, or through other client side
applications. New users must first be entered into the
DIRECTOR/DIRECTOR PRO’s database and their privileges or
permissions assigned.
The first step in entering new users into the database is to create profiles,
which define types or classes of users and their work privileges on the
DIRECTOR/DIRECTOR PRO. For example, a “Team Leader” profile
might be established for users who need to produce an unlimited number of
discs and a “Team Member” profile created for other users in order to
restrict the number of discs they can produce in a given period of time.
To create a new privilege profile:
•Click the New button below the PRIVILEGES window.
•Complete these required fields