Mi POE 4+4 GM User manual

Innovative Electronics for a changing world
MANUAL
POE 4+4 GM
Index:
Description
Technical and connections
Screen shots
Physical
Description:
The POE 4 +4 GM is an 4+4 = 8 Channel Gigabit DC passive power over Ethernet injector unit with a 10Mbs
anage ent Ethernet interface to allow the user to toggle the power output of each one of the 8 POE power
outputs via a web-browser interface.
POE output ports is Grouped into Group A (4 POE channels) and Group B (4 POE channels) –The user can select the
MODE (MODE B-2 pair power or PHANTOM POWER-4 pair power) and oltage (24VDC or 48VDC- input dependant)
for each group of 4 POE outputs individually via changing power connections at the rear of the unit.
The unit operates from 18Vdc to 60Vdc supply oltage for Group A and B .
Technical & Connections:
The unit have 8 LAN input Ports and 8 LAN + POE output ports via 70W POE+ Gigabit Ethernet transfor ers.
All Power output Ports on the device is protected via 1Amp PTC ther al self recoverable fuses against short circuits
and faulty equip ent that ight be connected to the port.
The unit controls power to each POE output port via mechanical relays for robustness on the power line fro
inco ing spikes on the power line caused by ESD discharges etc.
POE Port 1 to 8 can only be toggled to break power to the POE outputs 1 to 8 to reset connected devices.
The POE port will after being toggled – auto atically re-connect power to the connected device after 15 seconds so
the user can not log hi self out per anently of a connection to the re ote tower.
4+4 CHANNEL GB PASSI
VE DC POE STRIP WITH
MANAGEMENT
–
POE 4+4
GM
Mi

10Mbs User control Ethernet interface for re ote anage ent.
Each Port have led indication for port power status , led’s also indicates if the unit is connected in MODE B- 2pair
power or PHANTOM MODE-4pair power ode for POE A and POE B.
When POE A or POE B is connected in the MODE B mode – only the green led illuminates on the POE port
When POE A or POE B is connected in the PHANTOM mode – the green and amber led illuminates on the POE port
Rear view
POE A is the master unit and POE B is the sla e unit
The unit will not work if Power is connected to POE B only – always use POE A power input
RESET
To factory reset the unit to the default 192.168.1.2 IP address , disconnect power fro the unit , short circuit the 2
pins carefully as indicated by the arrow on the backside , apply power to POE A , wait 10seconds , re ove the short
circuit across the 2 reset pins.
Green pluggable terminals for power connection:
The unit can be powered fro the same supply voltage or fro two different supply voltages –see connection
diagra s below
** Reverse polarity connections could da age your POE connected equip ent**
Please be careful about correct polarity when connecting the power source
Each POE group , POE A (ch1-4) and POE B (ch1-4) can be wired to function in the
(sa e or different odes) and the (sa e or different) voltages.
MODES :
MODE B = 2 pair powering over LAN cable
PHANTOM = 4 pair powering over LAN cable
Provision was ade for the user to write the voltage for the POE A group and the POE B group onto the
front facia of the unit to avoid confusion between different voltage supplies between the channels
4+4 CHANNEL GB PASSI
VE DC POE STRIP WITH
MANAGEMENT
–
POE 4+4GM
Mi

4+4 CHANNEL GB PASSI
VE DC POE STRIP WITH
MANAGEMENT
–
POE 4+4GM
Mi

Screenshots:
Home page
Indicates PORT output power active with a green dot
POE ID – user can specify a site na e for the POE 4+4GM
4+4 CHANNEL GB PASSI
VE DC POE STRIP WITH
MANAGEMENT
–
POE 4+4GM
Mi

Selecting any enu will bring up the password pop up
Default : ad in & ad in
POE ID : user defined site na e for the POE 4+4GM
User can enter the voltage and the ode for POE A and POE B for reference
4+4 CHANNEL GB PASSI
VE DC POE STRIP WITH
MANAGEMENT
–
POE 4+4GM
Mi