Microchip Technology PD-9601-zzGC/AC User manual

PD-9601-zzGC/AC
Power over Ethernet Single-port Midspan User Guide
Introduction
Microchip’s family of PD-9601-zzGC Power over Ethernet (PoE) Midspans includes the PD-9601-10GC,
PD-9601‑5GC, and PD-9601-25GC models. Throughout this document, these three models are referred as the
PD-9601-zzGC.
The PD-9601-zzGC is a PoE Single Port Midspan/Injector that offers a compact and cost-effective power solution
for WLAN access points, network cameras, and other IP terminal installations. The PD-9601-zzGC inject power over
data‑carrying Ethernet cabling. The PD-9601-zzGC PoE Midspan/ Injector is IEEE® 802.3bt compliant and supplies
54 VDC to 4-pair wires (Alt A: 1, 2 (-) and 3, 6 (+)\Alt B: 4, 5 (+) and 7, 8 (-)) of a standard Ethernet cable in category
5E and above (for 2.5G), and category 6 and above (for 5G and 10G) enables delivery of both data and power to the
IP terminal. The PD-9601-zzGC can be powered through universal AC input and can provide up to 90W.
Features
PD-9601-zzGC PoE Midspan has the following key features:
• Single-Port PoE Output
• Guaranteed Power of 90W
• Compact Product Size
• Universal AC Input: 100 VAC to 240 VAC
• Standard Compliance: IEEE 802.3bt
• 10, 5, and 2.5 Gbps Pass-Through Data Rates
© 2022 Microchip Technology Inc.
and its subsidiaries
User Guide DS50003257A-page 1

Table of Contents
Introduction.....................................................................................................................................................1
Features.................................................................................................................................................. 1
1. Standards and Safety Guidelines............................................................................................................3
1.1. Part Number Definition.................................................................................................................3
1.2. Electrical Compatibility Approvals................................................................................................ 3
1.3. Safety Standard Approvals...........................................................................................................3
1.4. GS Marking.................................................................................................................................. 3
1.5. Safety Information........................................................................................................................ 4
2. Information en Matière de Sécurité......................................................................................................... 5
2.1. Directives Générales....................................................................................................................5
2.2. Mises en Garde............................................................................................................................5
3. PoE Midspan Installation.........................................................................................................................6
3.1. Connecting Ethernet Cables........................................................................................................ 6
3.2. Indicators......................................................................................................................................6
4. Troubleshooting.......................................................................................................................................7
4.1. Preliminary Steps......................................................................................................................... 7
4.2. Troubleshooting Steps..................................................................................................................7
5. Specifications.......................................................................................................................................... 8
5.1. Physical Specifications.................................................................................................................8
5.2. Environmental Specifications....................................................................................................... 8
5.3. Electrical Specifications................................................................................................................8
6. Contacting Technical Support................................................................................................................. 9
7. Revision History.................................................................................................................................... 10
The Microchip Website................................................................................................................................. 11
Product Change Notification Service............................................................................................................11
Customer Support........................................................................................................................................ 11
Microchip Devices Code Protection Feature................................................................................................ 11
Legal Notice................................................................................................................................................. 12
Trademarks.................................................................................................................................................. 12
Quality Management System....................................................................................................................... 13
Worldwide Sales and Service.......................................................................................................................14
PD-9601-zzGC/AC
© 2022 Microchip Technology Inc.
and its subsidiaries
User Guide DS50003257A-page 2

1. Standards and Safety Guidelines
The following sections mention the standard and safety guidelines for the product.
1.1 Part Number Definition
PD-9601-zzGC: AC input family.
Table 1-1. Part Number Definition
Symbol Description
zzGC Represents the bandwidth (zz—10, 5, or 2.5 Gbps).
AC Midspan has AC input.
1.2 Electrical Compatibility Approvals
Microchip’s PD-9601-zzGC Midspans complies with the following standards:
•FCC Part 15: Class B
• EN 55032: Class B
• Canadian ICES-003
• EN55035
• VCCI
1.3 Safety Standard Approvals
Microchip’s PD-9601-zzGC Midspans meets the following safety standards. Consult Microchip for a complete list of
safety certifications.
•UL/IEC/EN 62368-1
• GS Compliance
1.4 GS Marking
GS marking on this product indicates that the product complies with the German Product Safety Act.
PD-9601-zzGC/AC
Standards and Safety Guidelines
© 2022 Microchip Technology Inc.
and its subsidiaries
User Guide DS50003257A-page 3

1.5 Safety Information
Read the safety information before using the PoE Midspan unit.
1.5.1 General Guidelines
Read the following safety information before carrying out any installation, removal, or maintenance procedure on the
PoE Midspan. Warnings contain directions to be followed for the safety of personal and product.
1.5.2 Warnings
• Read installation instructions in 3. PoE Midspan Installation before connecting Midspan to its power source.
• Read instructions in 3. PoE Midspan Installation before connecting Midspan-to-Midspan power backup.
• Only trained and qualified personnel must be allowed to install, replace, and service this equipment.
• This ITE device must be connected to PoE (power supply over Ethernet) networks only, without routing to other
networks.
• The power cord must not be attached to the surface of the building or pass-through walls, ceilings, floors, and
similar openings in the building structure.
• Steps must be taken to prevent physical damage to the power cord, including proper routing.
• This product relies on building installation for short-circuit (over-current) protection. Use only a fuse or circuit
breaker not higher than 15A for 120 VAC (U.S.) or 10A for 230 VAC (international).
• All wiring and connections must conform to NFPA 70 (NEC).
• Do not work on the system or connect/disconnect cables during lightning storms.
• A voltage mismatch can damage the equipment and can pose a fire hazard. If voltage indicated on the label is
different from the power outlet voltage, do not connect Midspan to this outlet.
• For shelf-mounted equipment, verify that surface is stable and strong enough to support the equipment. Do not
stack more than four Midspan units.
• When disposing this product, follow all local laws and regulations.
•Data and Data and Power ports of the Midspan are shielded RJ-45 data sockets. They cannot be used as Plain
Old Telephone Service (POTS) sockets. Only connect RJ-45 data connectors to these sockets.
• Associated Ethernet wiring must be limited to the inside of the building.
PD-9601-zzGC/AC
Standards and Safety Guidelines
© 2022 Microchip Technology Inc.
and its subsidiaries
User Guide DS50003257A-page 4

2. Information en Matière de Sécurité
Lire les informations suivantes en matière de sécurité avant d'utiliser d'activer l'alimentation sur votre appareil
Ethernet Midspan.
2.1 Directives Générales
Lire les informations suivantes en matière de sécurité avant d'installer ou enlever quoi que ce soit, ou procéder à
l'entretien de l'alimentation de votre appareil Ethernet Midspan. Les mises en garde contiennent des instructions qui
doivent être suivies pour la sécurité des personnes et du produit. Suivre les instructions soigneusement.
2.2 Mises en Garde
• Lire les instructions d'installation dans la cette 3. PoE Midspan Installation avant de connecter le Midspan à une
source d'alimentation.
• Lire les instructions d'installation dans la cette 3. PoE Midspan Installation avant de connecter le Midspan à une
source de sauvegarde Midspan.
• Seul du personnel formé et qualifié doit être autorisé à installer, remplacer et entretenir cet équipement.
• Cet ITE appareil doit être branché à des réseaux PoE (alimentation électrique par Ethernet) seulement, et ce,
sans routage vers d'autres réseaux.
• Le cordon d'alimentation ne doit pas être fixé à la surface du bâtiment ni traverser les murs, les plafonds, les
planchers et les ouvertures similaires de la structure du bâtiment.
• Des mesures doivent être prises pour éviter tout dommage physique au cordon d'alimentation, y compris un
acheminement approprié.
• Ce produit dépend de l'installation électrique de l'immeuble pour une protection contre les courts-circuits
(surcharges de courant). Utiliser seulement un fusible ou un disjoncteur dont la puissance ne dépasse pas
15A pour 120VAC (É.-U.), ou 10A pour 230VAC (international).
• Tout le câblage et les connexions doivent être conformes à la norme NFPA 70 (NEC).
• Ne pas exécuter de travaux sur le système, connecter ou déconnecter des câbles pendant les orages.
• Une disparité de voltage peut endommager l'équipement et constituer un risque d'incendie. Si le voltage indiqué
sur l'étiquette est différent du voltage de la source d'alimentation, ne pas connecter le Midspan à cette prise.
• Pour un équipement monté sur une tablette, vérifier que la surface est stable et suffisamment solide pour le
supporter. Ne jamais empiler plus de quatre unités Midspan.
• Pour disposer/jeter ce produit, suivre les lois et règlements locaux.
• Les ports Data et Data et Power du PoE Midspan sont des prises de données blindées RJ45. Elles ne peuvent
pas être utilisées comme prises de service téléphonique traditionnel. Connecter seulement des connecteurs de
données RJ45 à ces prises. Le câblage Ethernet connexe doit être limité à l'intérieur de l'immeuble.
• Le câblage Ethernet associé doit être limité à l'intérieur du bâtiment.
PD-9601-zzGC/AC
Information en Matière de Sécurité
© 2022 Microchip Technology Inc.
and its subsidiaries
User Guide DS50003257A-page 5

3. PoE Midspan Installation
Follow the installation steps carefully:
1. Connect the PD-9601-zzGC to an AC outlet (100 VAC to 240 VAC).
2. Connect the Data In jack (input) to the remote Ethernet network switch's patch panel.
3. Connect the Power Out jack (output) to Terminal.
Figure 3-1. Installing the PD-9601-zzGC
Terminal Ethernet
Port
Output
Port
Input
Main LED
Indication
Terminal Ethernet
Port
Output
Port
Input
Main LED
Indication
3.1 Connecting Ethernet Cables
The ports on the PD-9601-zzGC Midspan are configured as Pass Through ports for conductors of RJ45 connectors.
Use Category 5e/6 cabling while making connections. See Figure 3-1.
1. Connect Ethernet 10/5/2.5G Base-T input (Ethernet) cable to RJ45 female socket on PD-9601-25\5GCO.
2. Connect Ethernet 10/5/2.5G Base-T, Plus 54 VDC output (Terminal) cable to RJ45 female socket, with DC
voltage on wire pairs, (Alt A: 1, 2 (-) and 3, 6 (+)\Alt B: 4, 5 (+) and 7, 8 (-)).
3.2 Indicators
The following table lists the set of indicators displaying the status of the PoE Midspan and its ports.
Table 3-1. Port Indicator LED
Port LED Color Port Load Conditions
Orange ON Power input is active
Orange Blinking Power input error
Blue ON Port ON—PoE over 2P
Blue Blinking Port error
Green ON Port ON—PoE over 4P
Green Blinking Port error
PD-9601-zzGC/AC
PoE Midspan Installation
© 2022 Microchip Technology Inc.
and its subsidiaries
User Guide DS50003257A-page 6

4. Troubleshooting
The following sections describe the troubleshooting procedures to address any problems with a unit.
4.1 Preliminary Steps
• Read installation instructions before connecting the PD-9601-zzGC to its power source.
• There is no ON/OFF switch on the PD, simply plug the PD-9601-zzGC into an AC power source.
• Verify that a PoE Ready Ethernet-compatible device is connected.
• Do not cover PD-9601-zzGC or block airflow to the unit with any foreign objects. Keep PD-9601-zzGC away
from excessive heat and humidity, and free from vibration and dust.
• Ensure that cable length from Ethernet network source to the terminal does not exceed 100 meters (330 feet).
This Midspan is not a repeater and does not amplify Ethernet data signal.
• Use a splitter, if necessary, and ensure that the splitter is connected near the terminal and not on the PD-9601-
zzGC.
4.2 Troubleshooting Steps
The following table lists problem and resolution sequences to assist in troubleshooting minor operating problems. If
the following steps do not solve your problem, contact the dealer for further assistance.
Table 4-1. Troubleshooting Steps
Problem Corrective Steps
Midspan does not power-up. 1. Verify that an approved power cord is used.
2. Ensure that power cord is properly connected.
3. Verify that the voltage at the power inlet is between 100 VAC to 240 VAC.
4. Remove and re-apply power to the device and check indicators during power-
up sequence.
A port indicator is not lit and
corresponding PD does not
operate.
1. Verify that the PD is designed for PoE operation according to IEEE 802.3bt
standard.
2. Verify that you are using a standard straight‑wired four-pair cable (UTP/FTP
Category 5e/6).
3. Verify that the PD is connected to the PD-9601-zzGC Terminal port.
4. If an external power splitter is in use, replace it with a viable splitter.
5. Remove and re-apply power to the Midspan.
End device operates but
there is no data link.
1. Verify that for this link you are using a standard UTP/FTP Category 5e/6
straight (non-crossover) cabling, with all four pairs, and that link is 100 meters
long.
2. Verify that the Ethernet cable length is less than 100 meters from Ethernet
source to load/remote terminal.
3. Ensure that the input Ethernet cable is connected to the power injector’s
Ethernet port.
4. If an external power splitter is in use, replace it with a viable splitter.
PD-9601-zzGC/AC
Troubleshooting
© 2022 Microchip Technology Inc.
and its subsidiaries
User Guide DS50003257A-page 7

5. Specifications
The following sections describe unit specifications of PD-9601-zzGC unit.
5.1 Physical Specifications
Table 5-1. Dimensions
Parameter Dimensions
In mm In inch
Height 48.6 1.91
Width 84.4 3.32
Length 162.1 6.38
Table 5-2. Physical Specifications
Part Number Weight
PD-9601-zzGC 550 g (1.21 lb)
5.2 Environmental Specifications
Table 5-3. Environmental Specifications
Mode Temperature Humidity
Operating 0°C to 40°C
32°F to 104°F
90% (non-condensing)
Storage –20°C to 70°C
–4°F to 158°F
95% (non-condensing)
5.3 Electrical Specifications
Table 5-4. Electrical Specifications
Parameter Value
Input voltage 100 VAC to 240 VAC (50/60 Hz)
Input current 1.6A
Available output power (maximum) 90W
Nominal output voltage 54 VDC
PD-9601-zzGC/AC
Specifications
© 2022 Microchip Technology Inc.
and its subsidiaries
User Guide DS50003257A-page 8

6. Contacting Technical Support
If you encounter any problems while installing or using this product, consult Microchip technical support team through
the website or contact on the following number:
USA/Canada
Telephone: [phone]
Internet: www.microchip.com/support
PD-9601-zzGC/AC
Contacting Technical Support
© 2022 Microchip Technology Inc.
and its subsidiaries
User Guide DS50003257A-page 9

7. Revision History
Revision Date Description
A 01/2022 Initial Revision
PD-9601-zzGC/AC
Revision History
© 2022 Microchip Technology Inc.
and its subsidiaries
User Guide DS50003257A-page 10