Microlife BP AG1-10 User manual

IB AG1-10_e-f-s-ru_ 4706
Europe / Middle-East / Africa
Microlife AG
Espenstrasse 139
9443 Widnau / Switzerland
Tel. +41 / 71 727 70 30
Fax +41 / 71 727 70 39
Email [email protected]
www.microlife.com
Asia
Microlife Corporation.
9F, 431, RuiGang Road, NeiHu
Taipei, 114, Taiwan, R.O.C.
Tel. [phone]
Fax.[phone]
Email [email protected]
www.microlife.com
North / Central / South America
Microlife USA, Inc.
424 Skinner Blvd., Suite C
Dunedin, FL 34698 / USA
Tel. [phone]
Fax [phone]
Email [email protected]
www.microlife.com
IB AG1-10 e_f_s_ru 4706.qxd 11/22/06 8:55 AM Page 1

microlife BP AG1-10
Aneroid Blood Pressure Kit
Instruction Manual (1-13)
Tensiomètre anéroïde en trousse
Mode d’emploi (14-27)
Kit aneroide de tensión arterial
Manual de instrucciones (28-41)
ååÂÂıı‡‡ÌÌˢ˜ÂÂÒÒÍÍËËÈÈÔÔËË··ÓÓ‰‰ÎÎflfl
ËËÁÁÏÏÂÂÂÂÌÌËËflfl‡‡ÚÚÂÂˡ‡Îθ¸ÌÌÓÓ„„ÓÓ‰‰‡‡‚‚ÎÎÂÂÌÌËËflfl
–ÛÍÓ‚Ó‰ÒÚ‚Ó ÔÓ ÔÓθÁÓ‚‡Ì˲ (42-55)
IB AG1-10 e_f_s_ru 4706.qxd 11/22/06 8:55 AM Page 2

Aneroid Blood Pressure Kit
Instruction Manual
IB AG1-10 e_f_s_ru 4706.qxd 11/22/06 8:55 AM Page 3

Table of contents
1. Introduction
1.1. Features
1.2. Important information about self-measurement
2. Important information on the subject of blood-pressure and its measurement
2.1. How does high/low blood-pressure arise?
2.2. Which values are normal?
2.3. What can be done, if regular high/low values are obtained?
3. The various components of the blood-pressure kit
4. Carrying out a measurement
4.1. Before the measurement
4.2. Common sources of error
4.3. Fitting the cuff
4.4. Measuring procedure
4.4.1. Putting the chestpiece under the cuff
4.4.2. Inflating the cuff
4.4.3. Systolic blood pressure reading
4.4.4. Diastolic blood pressure reading
4.4.5. Recording your readings
5. Malfunction / Troubleshooting
6. Care and maintenance, recalibration
7. Guarantee
8. Reference to standards
9. www.microlife.com
10. Technical specifications
1
IB AG1-10 e_f_s_ru 4706.qxd 11/22/06 8:55 AM Page 1

1. Introduction
1.1. Features
The aneroid blood pressure kit is a non-automated, mechanical blood-pressure measuring device
for use on the upper arm.
It offers proven reliability and superior performance at an economical price. With the advanced
non-stop pin mechanism and ergonomic bulb with complete valves, the BP AG1-10 ensure you a
precise and consistent measurement. Its oversized cuff can be applied to users whose arm
circumference ist 25 the least and up to 40 cm. Nevertheless, its durable nylon cuff, high-grade
bearing and aneroid bellow provide consistent operation. The entire unit stores in a zippered
Nylon bag for easy portability.
Before using, please read through this instruction manual carefully and then keep it in a safe
place. For further questions on the subject of blood-pressure and its measurement, please
contact your doctor.
Attention!
1.2. Important information about self-measurement
• Do not forget: self-measurement means control, not diagnosis or treatment. Unusual
values must always be discussed with your doctor. Under no circumstances should you alter
the dosages of any drugs prescribed by your doctor.
2. Important information on the subject of blood-pressure and its measurement
2.1. How does high/low blood-pressure arise?
The level of blood-pressure is determined in a part of the brain, the so-called circulatory centre,
and adapted to the respective situation by way of feedback via the nervous system. To adjust the
blood-pressure, the strength and frequency of the heart (Pulse), as well as the width of circulatory
blood vessels is altered. The latter is effected by way of fine muscles in the blood-vessel walls.
The level of arterial blood-pressure changes periodically during the heart activity: During the
2
IB AG1-10 e_f_s_ru 4706.qxd 11/22/06 8:55 AM Page 2

3
«blood ejection» (Systole) the value is maximal (systolic blood-pressure value), at the end of the
heart’s «rest period» (Diastole) minimal (diastolic blood-pressure value). The blood-pressure
values must lie within certain normal ranges in order to prevent particular diseases.
2.2 Which values are normal?
Blood pressure is too high if at rest, the diastolic pressure is above 90mmHg and/or the systolic
blood-pressure is over 140mmHg. In this case, please consult your doctor immediately. Long-term
values at this level endanger your health due to the associated advancing damage to the blood
vessels in your body.
With blood-pressure values that are too low, i.e. systolic values under 100mmHg and/or diastolic
values under 60mmHg, likewise, please consult your doctor.
Even with normal blood-pressure values, a regular self-check with your blood-pressure monitor is re-
commended. In this way you can detect possible changes in your values early and react appropriately.
If you are undergoing medical treatment to control your blood pressure, please keep a record of
the level of your blood pressure by carrying out regular self-measurements at specific times of
the day. Show these values to your doctor. Never use the results of your measurements to
alter independently the drug doses prescribed by your doctor.
Table for classifying blood-pressure values (units mmHg) according to World Health Organization:
Range Systolic Diastolic Measures
Blood-pressure Blood-pressure
Hypotension lower than 100 lower than 60 Consult your doctor
Normal range between 100 and 140 between 60 and 90 Self-check
Mild hypertension between 140 and 160 between 90 and 100 Consult your doctor
Moderately serious between 160 and 180 between 100 and 110 Consult your doctor
hypertension
Serious hypertension higher than 180 higher than 110 Consult your doctor
immediately
IB AG1-10 e_f_s_ru 4706.qxd 11/22/06 8:55 AM Page 3

☞Further information
• If your values are mostly standard under resting conditions but exceptionally high under con-
ditions of physical or psychological stress, it is possible that you are suffering from so-called
«labile hypertension». Please consult your doctor if you suspect that this might be the case.
• Correctly measured diastolic blood-pressure values above 120mmHg require immediate
medical treatment.
2.3. What can be done, if regular increased/low values are obtained?
a) Please consult your doctor.
b) Increased blood-pressure values (various forms of hypertension) are associated long- and
medium term with considerable risks to health. This concerns the arterial blood vessels of
your body, which are endangered due to constriction caused by deposits in the vessel walls
(Arteriosclerosis). A deficient supply of blood to important organs (heart, brain, muscles) can
be the result. Furthermore, with long-term continuously increased blood-pressure values, the
heart will become structurally damaged.
c) There are many different causes of the appearance of high blood pressure. We differentiate
between the common primary (essential) hypertension, and secondary hypertension. The
latter group can be ascribed to specific organic malfunctions. Please consult your doctor for
information about the possible origins of your own increased blood pressure values.
d) There are measures which you can take, not only for reducing a medically established high
blood pressure, but also for prevention. These measures are part of your general way of life:
A) Eating habits
• Strive for a normal weight corresponding to your age. Reduce overweight!
• Avoid excessive consumption of common salt.
• Avoid fatty foods.
B) Previous illnesses
Follow consistently any medical instructions for treating previous illness such as:
• Diabetes (Diabetes mellitus)
• Fat metabolism disorder
• Gout
4
IB AG1-10 e_f_s_ru 4706.qxd 11/22/06 8:55 AM Page 4

5
C) Habits
• Give up smoking completely
• Drink only moderate amounts of alcohol
• Restrict your caffeine consumption (Coffee)
D) Physical constitution
• After a preliminary medical examination, do regular sport.
• Choose sports which require stamina and avoid those which require strength.
• Avoid reaching the limit of your performance.
• With previous illnesses and/or an age of over 40 years, please consult your doctor before
beginning your sporting activities. He will advise you regarding the type and extent of types
of sport that are possible for you.
3. The various components of the Aneroid Blood Pressure Kit
The illustration shows the BP AG1-10, consisting of:
a) Measuring unit:
b) Cuff:
Type ACXLNP-1, for arm circumference 25-40 cm
Soft bag
Cuff
Manometer
Bulb & Valves
IB AG1-10 e_f_s_ru 4706.qxd 11/22/06 8:55 AM Page 5

4. Carrying out a measurement
4.1. Before the measurement
• Avoid eating, smoking as well as all forms of exertion directly before the measurement. All
these factors influence the measurement result. Try and find time to relax by sitting in an
armchair in a quite atmosphere for about ten minutes before the measurement.
• Remove any garment that fits closely to your upper arm.
• Measure always on the same wrist (normally left).
• Attempt to carry out the measurements regularly at the same time of day, since the blood-
pressure changes during the course of the day.
4.2. Common sources of error
Note: Comparable blood-pressure measurements always require the same conditions! These are
normally always quiet conditions.
• All efforts by the patient to support the arm can increase the blood-pressure. Make sure you
are in a comfortable, relaxed position and do not activate any of the muscles in the measu-
rement arm during the measurement. Use a cushion for support if necessary.
• If the arm artery lies considerably lower (higher) than the heart, an erroneously higher
(lower) blood-pressure will be measured! (Each 15cm difference in height results in a
measurement error of 10mmHg!)
• Cuffs that are too narrow or too short result in false measurement values. Selecting the correct
cuff is of extraordinary importance. The cuff size is dependent upon the circumference of the arm
(measured in the centre). The permissible range is printed on the cuff. If this is not suitable for
your use, please contact your dealer. Note: Only use clinically approved Original-Cuffs!
• A loose cuff or a sideways protruding air-pocket causes false measurement values.
4.3. Fitting the cuff
a) Push the cuff over the left upper arm so that the tube
points in the direction of the lower arm.
6
IB AG1-10 e_f_s_ru 4706.qxd 11/22/06 8:55 AM Page 6

7
b) Lay the cuff on the arm as illustrated. Make certain
that the lower edge of the cuff lies approximately
2 to 3 cm above the elbow and that the rubber tube
leaves the cuff on the inner side of the arm.
Important! The mark (ca. 3 cm long bar) must lie
exactly over the artery which runs down the inner
side of the arm.
c) Tighten the free end of the cuff and close the cuff
with the closer.
d) There must be no free space between the arm and
the cuff as this would influence the result. Clothing
must not restrict the arm. Any piece of clothing which
does (e.g. a pullover) must be taken off.
e) Secure the cuff with the Velcro closer in such a way
that it lies comfortably and is not too tight. Lay the
arm on the table (palm upwards) so that the cuff is at
the same height as the heart. Make sure that the
tube is not kinked.
f) Remain seated quietly for two minutes before you
begin the measurement.
Comment:
If it is not possible to fit the cuff to the left arm, it can also be placed on the right one. However
all measurements should be made using the same arm.
2–3 cm
tube
IB AG1-10 e_f_s_ru 4706.qxd 11/22/06 8:55 AM Page 7

4.4. Measuring procedure
4.4.1. Put the chestpiece under the cuff
The chestpiece shall not be placed ON or INTO the cuff, it shall be
placed either under the cuff, or 1-2cm below it. The chestpiece is
then placed correctly , when the Korrotkoff's sound appears
strongest ('loudest'). Make sure the chestpiece is in contact with
skin and above the brachial artery. Wear the binaural ( earpieces )
properly to check the Korotkoff’s sound during measurement.
Before using the stethoscope, be sure there is no crack on the
diaphragm, earpieces, and tubing. Any improper setup or damage
of the stethoscope will cause distorted sound or poor sound
transmission to make inaccurate reading.
4.4.2. Inflating the cuff
Close the air valve on the bulb by turning the screw clockwise.
Do not over-tighten. Squeeze the inflation bulb with the hand at
a steady rate until the pointer on the gauge is 30mmHg above
your normal systolic pressure value. If you are not sure the
value, inflate to 200mmHg first.
4.4.3. Systolic blood pressure reading
Slowly open air valve by turning screw counter clockwise and
hold stethoscope chestpiece over brachial artery. Proper de-
flation rate is essential for an accurate reading, so you should
practice and master a recommended deflation rate of 2-3mmHg
per second or a drop of 1-2 marks on the pressure gauge each
heartbeat. You should not keep the cuff inflated any longer than
necessary. As the cuff begins to deflate, you must listen care-
fully with the stethoscope. Note the reading on the gauge as
soon as you hear a faint, rhythmic tapping or thumping sounds.
This is the systolic blood pressure reading. Listen carefully and
familiarize yourself with pulse ( Korotkoff’s ) sound.
8
IB AG1-10 e_f_s_ru 4706.qxd 11/22/06 8:55 AM Page 8

9
4.4.4. Diastolic blood pressure reading
Allow the pressure to continue dropping at the same deflation rate. When your diastolic blood
pressure value reached, the thumping sound stops. Deflate the cuff valve completely. Remove the
cuff from arm and stethoscope from ears.
4.4.5. Record your readings
Repeat the measurement at least two times. Do not forget to record your readings and the time
of the day measurement is made immediately after you finish measuring. A suitable time is first
thing in the morning, or just before evening meals. Remember that your
physician is the only person qualified to analyze your blood pressure.
☞Further information
Measurements should not occur soon after each other, since otherwise, the results will be
falsified. Wait therefore for several minutes in a relaxed position, sitting or lying, before you
repeat a measurement.
5. Other possible malfunctions and their elimination
If problems occur when using the device, the following points should be checked and if
necessary, the corresponding measures are to be taken:
Malfunction
The sound transmission is poor,
distorted or there is extraneous noise.
Remedy
1. Check the earpieces if they are plugged or cracked.
If not, make sure they do not fit poorly as worn.
2. Check the tube if it is broken or twisted.
3. Check the bell and diaphragm of chestpiece if
there is any crack.
4. Make sure the chestpiece is in proper contact with
skin and over brachial artery during measuring.
Clean or replace any defective parts if found to
avoid inaccurate reading.
IB AG1-10 e_f_s_ru 4706.qxd 11/22/06 8:55 AM Page 9

The pressure does not rise although
the bulb is pumping.
The deflation rate can not be set to
2-3 mmHg/ sec. by adjusting the air
release valve.
Pointer is not at 0 +/- 3 mmHg at rest.
☞FURTHER INFORMATION
The level of blood-pressure is subject to fluctuations even with healthy people. Important thereby
is, that comparable measurements always require the same conditions (rest condition)!
If, in spite of observing all these factors, the fluctuations are more than 15mmHg, and/or you
hear irregular pulses on several occasions, please consult your doctor.
You must consult your specialist dealer or chemist if there are technical problems with the blood-
pressure instrument. Never attempt to repair the instrument yourself!
Any unauthorised opening of the instrument invalidates all guarantee claims!
6. Care and maintenance, recalibration
With proper care and maintenance, this blood-pressure measuring device will provide years of
satisfactory service. Follow the general Rules below:
• Do not drop .
• Never inflate beyond 300mmHg.
• Do not expose the device to either extreme temparatures, humidity, or direct sunlight.
10
1. Make sure that the valve is closed.
2. Make sure the cuff is properly connected to bulb
and manometer
3. Check if the cuff, tube and bulb is leaky. Replace
the defective parts if any
• Disassemble the valve from bulb to check if there
is any blockage in the airway of the valve. Clean
the blockage and try again. If it still does not work,
replace it to avoid inaccurate reading.
1. Make sure that the valve is open for zero check.
2. If still more than 3mmHg deviation, contact your
dealer to recalibrate the manometer.
IB AG1-10 e_f_s_ru 4706.qxd 11/22/06 8:55 AM Page 10

11
• Never contact the cuff fabric with a sharp instrument, since this could cause damage.
• Always deflate cuff completely before storage.
• Do not dismantle manometer under any circumstance.
• Store the whole device in storage bag provided, to keep all the parts clean.
• Storage temperature condition: -20 C to 70 C at a relative air humidity of 85% (non-
condensing).
• Wipe off the manometer and bulb with a damp cloth. Sterilization is not necessary, since the
parts of manometer should not come into direct contact with the patient‘s body during
measurement.
• Remove the bladder first, and wipe the velcro, bladder and tubes with a damp cloth. The cuff can
be washed with soap and cold water. But do rinse the cuff with clear water and keep it air dry.
Periodical recalibration
Sensitive measuring devices must from time to time be checked for accuracy. We therefore
recommend a periodical inspection of the static pressure display every 2 years.
Your specialist dealer would be pleased to provide more extensive information about this.
7. Guarantee
This blood-pressure monitor is guaranteed for 1 year from date of purchase. This guarantee
includes the instrument and the cuff. The guarantee does not apply to damage caused by
improper handling, accidents, not following the operating instructions or alterations made to the
instrument by third parties.
The guarantee is only valid upon presentation of the guarantee card filled out by the dealer.
Name and company address of the responsible dealer:
IB AG1-10 e_f_s_ru 4706.qxd 11/22/06 8:55 AM Page 11

8. Reference to standards
Device standard: Device corresponds to the requirements of the
EN1060-1 /-2 / 1995
ANSI / AAMI SP09
9. www.microlife.com
Detailed user information about our products as well as services can be found at
www.microlife.com
12
IB AG1-10 e_f_s_ru 4706.qxd 11/22/06 8:55 AM Page 12

13
10. Technical specifications
Weight: 360g
Size: 175x70x103mm
Storage temperature: –20 to +70°C
Humidity: 85% relative humidity maximum
Operation temperature: 0°C to 46 °C
Measuring range: 0 to 300 mmHg
Measuring resolution: 2 mmHg
Accuracy: within ±3mmHg in 18°C to 33°C ;
within ±6mmHg in 34°C to 46°C
Inflation source: a volume of at least 200cc to a pressure of
300mmHg in 4 to 10 sec
Air leakage: <±4mmHg/min
Hysteresis error: within 0mmHg to 4mmHg
Accessories: 1. cuff (oversized with arm circumference of
25-40cm) with inlaid latex bladder
2. bulb and valve
3. soft bag
Technical alterations reserved!
IB AG1-10 e_f_s_ru 4706.qxd 11/22/06 8:55 AM Page 13

Tensiomètre anéroïde en trousse
Mode d’emploi
14
IB AG1-10 e_f_s_ru 4706.qxd 11/22/06 8:55 AM Page 14

15
Table des matières
1. Introduction
1.1. Caractéristiques
1.2. Informations importantes pour prendre soi-même sa tension artérielle
2. Informations importantes concernant la tension artérielle et sa mesure
2.1. Quelle est l’origine d’une tension basse/haute?
2.2. Quelles sont les valeurs normales?
2.3. Que faire lorsque les valeurs déterminées sont régulièrement trop élevées/trop basses?
3. Les différents éléments du tensiomètre anéroïde en trousse
4. Prise de mesure
4.1. Avant d’effectuer une mesure
4.2. Sources fréquentes d’erreur
4.3. Mise en place du brassard
4.4. Procédure de mesure
4.4.1. Positionnement du pavillon par rapport au brassard
4.4.2. Gonflage du brassard
4.4.3. Lecture de la tension artérielle systolique
4.4.4. Lecture de la tension artérielle diastolique
4.4.5. Enregistrement des relevés
5. Dysfonctionnements / solutions
6. Entretien, précautions et réétalonnage
7. Garantie
8. Références aux normes
9. www.microlife.com
10. Données techniques
IB AG1-10 e_f_s_ru 4706.qxd 11/22/06 8:55 AM Page 15

1. Introduction
1.1. Caractéristiques
Le tensiomètre est un appareil de prise de tension artérielle mécanique, non automatisé, qui
s’utilise sur le haut du bras. Sa fiabilité et ses excellentes performantes sont prouvées et il est
d’un prix économique. Grâce à son mécanisme perfectionné rotatif en continu et à sa poire
ergonomique à valve intégrée, le BP AG1-10 vous garantit un relevé précis et stable. Son
brassard grand taille convient aux sujets dont le tour de bras va de 25 cm minimum à 40 cm. En
outre, son brassard en nylon résistant, son palier de haute qualité et son soufflet anéroïde
garantissent un fonctionnement régulier. L’unité complète se range dans un sac en nylon avec
fermeture éclair facile à transporter.
Veuillez lire attentivement ce mode d’emploi avant utilisation puis rangez-le dans un endroit sûr.
Pour toute autre question concernant la tension artérielle et sa mesure, veuillez vous adresser à
votre médecin.
Attention !
1.2. Informations importantes pour prendre soi-même sa tension artérielle
• N’oubliez pas: en prenant soi-même sa tension, on ne fait qu’un contrôle, ce n’est ni un
diagnostic ni un traitement. Lorsque les valeurs sont anormales, il faut toujours en parler à
un médecin. Ne modifiez sous aucun prétexte par vous-même les doses de médicament
prescrites par votre médecin.
2. Informations importantes concernant la tension artérielle et sa mesure
2.1. Quelle est l’origine d’une tension basse/haute?
Le niveau de la tension est déterminé dans une partie du cerveau appelée centre cardio-vascu-
laire et est adapté à chaque situation par le biais de réactions passant par le système nerveux.
Pour réguler la tension sont modifiés la force de battement du cœur et sa fréquence (pouls) ainsi
que le diamètre des vaisseaux sanguins. Cette modification est faite par de fins muscles qui se
trouvent dans les parois des vaisseaux sanguins.
16
IB AG1-10 e_f_s_ru 4706.qxd 11/22/06 8:55 AM Page 16

17
Le niveau de la tension artérielle change périodiquement au cours de l’activité cardiaque: Lorsque
le sang est «éjecté» (systole), la valeur est à son maximum (tension systolique), à la fin de la
«période de repos» du cœur (diastole), elle est à son minimum (tension diastollique). Les valeurs
de la tension doivent se situer dans des registres normaux pour prévenir certaines maladies.
2.2 Quelles sont les valeurs normales?
La tension est trop élevée lorsqu’au repos, la tension diastolique dépasse 90 mmHg et/ou la
tension systolique 140 mmHg. Dans ce cas, veuillez consulter immédiatement votre médecin.
A long terme, un niveau de tension aussi élevé est un risque pour votre santé parce qu’il
s’accompagne de lésions progressives des vaisseaux sanguins de votre corps.
De même, veuillez consulter votre médecin si la tension est trop basse, c’est à dire si les valeurs
systoliques sont inférieures à 100 mmHg et/ou les valeurs diastoliques inférieures à 60 mmHg.
Même si votre tension est normale, il est recommandé que vous fassiez vous-même des
contrôles réguliers avec votre tensiomètre. Vous pouvez ainsi détecter suffisamment tôt
d’éventuels changements de vos valeurs et réagir en conséquence.
Si vous deviez vous trouver en traitement médical pour réguler votre tension, veuillez tenir à jour
le niveau de votre tension en prenant régulièrement des mesures à heures fixes. Présentez ces
valeurs à votre médecin. Ne modifiez jamais par vous-même les doses de médicament
prescrites par votre médecin en vous basant sur vos résultats.
Tableau de classification des valeurs de tension (unité mmHg) selon l'Organisation Mondiale de la Santé:
Plage Tension systolique Tension diastolique Dispositions à prendre
Hypotension inférieure à 100 inférieure à 60 Consultation médicale
Tension normale entre 100 et 140 entre 60 et 90 Contrôle personnel
Légère hypertension entre 140 et 160 entre 90 et 100 Consultation médicale
Hypertension entre 160 et 180 entre 100 et 110 Consultation médicale
moyennement grave
Hypertension grave supérieure à 180 supérieure à 110 Consultation médicale
d'urgence
IB AG1-10 e_f_s_ru 4706.qxd 11/22/06 8:55 AM Page 17