Microtek mii-900 plus User manual

www.microtek.com
NDT/RT Film Digitizer
User's Manual

2 MII-900 Plus User's Manual
Preface
Copyright
© 2014, Microtek International, Inc., all rights reserved. This document may not
be reproduced or copied in any way, stored electronically, or translated into any
language, without the permission of Microtek International, Inc.
Trademarks
Microtek, ScanMaker, ArtixScan, ScanWizard and ColoRescue are trademarks or
registered trademarks of Microtek International, Inc. All other trademarks or
registered trademarks are the property of their respective holders. Specifications,
software and hardware bundles are subject to change without notice. Not
responsible for typographical errors.
Disclaimer
The contents of this manual have been checked carefully for accuracy, and every
effort has been made to ensure that there are no errors. However, Microtek makes
no guarantee as to the accuracy of the contents of this document and reserves the
right to make changes to the contents without prior warning.
I49-004974 A
May 2014
Microtek International, Inc.
6, Industry East Road 3, Science Based Industrial Park, Hsinchu, 30077, Taiwan
Tel: [phone], Fax: [phone], http://www.microtek.com

MII-900 Plus User's Manual 3
FCC Compliance Statement
This equipment (Model: MSS-2400XU2L) has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Note: A shielded Hi-Speed USB interface cable with ferrite core installed on the
film digitizer connector end must be used with this equipment.
Caution: Changes or modifications not expressly approved by the manufacturer
responsible for compliance could void the user's authority to operate the
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.

4 MII-900 Plus User's Manual
CE Compliance Statement
This device complies with CE Certification pursuant to
EN 55011:2007+A2:2007
EN 60601-1-2:2007
WEEE Compliance Statement
Microtek International, Inc. operates under full compliance with the WEEE
Directive. Among the requirements of the Directive are the marking of any
applicable equipment placed in the EU market with the WEEE symbol, a crossed
out wheeled bin as shown at left; demonstration of the implementation of a take-
back program; and meeting recycling targets.
ISO Compliance Statement
Comply with the requirements of the international quality standard
ISO 9001:2000 and ISO 13485:2003

MII-900 Plus User's Manual 5
Safety Precautions
Before using your digitizer, read the following safety guides carefully, which detail
the proper operation of the digitizer and its accessories to prevent injuries or
damage to users or equipment.
Meanings of Symbol Signs
This indicates hazardous situation which, if not payed
attention, could result injury or damage to users or
equipment.
This indicates hazardous situation which, if not payed
attention, could result serious injury or death to users.
Power Supply:
• Use a power source only with a power rating specified on the marking label.
• Ensure to turn off the power of each device before connecting or
disconnecting the cables.
• Insert the plug completely into the outlet, as a loose connection may cause
arcing and result in fire.
• Ensure to hold the plug or connector to disconnect the cable; otherwise, if
you pull the cable only, it may damage the core wire and result in fire or
electric shock.
• Place and route the power supply cord such that it is not likely to be walked
on or pinched by items placed upon or against them, paying particular
attention to the cord near the power plugs, convenience receptacles, and at
the point where it exits from the outlet.
• When the digitizer is left unattended and unused for long periods of time,
unplug it from the wall outlet.
Moving and Storing the Film Digitizer:
• Always ensure that the digitizer is stored properly before shipping or moving
it. Quick stops, excessive force, and uneven surfaces may cause the product
to overturn when moving.
• Do not hit or drop the digitizer. The digitizer may be damaged if it receives a
strong jolt, which may result in fire or electric shock if the digitizer is used
without being repaired.
• Do not place the digitizer on any slippery, slanted, or unstable surface. The
product may slide or fall, causing serious injury to people as well as serious
damage to the product.
CAUTION
WARNING

6 MII-900 Plus User's Manual
• Do not use the digitizer near water. Never spill liquid of any kinds on the
product, or it may result in electric shock or other hazards.
• This digitizer should be situated away from heat sources such as radiators,
heat registers, stoves, or other products (including amplifiers) that produce
heat.
• Do not store the digitizer in which it may be exposed to direct sunlight.
Using the Digitizer
• Before using the digitizer, make sure the area of the front cover is clear from
any objects that may cause jams inside.
• When using the digitizer, if your hairs have been jammed into the front cover
of the digitizer, turn off the power switch immediately. Do not attend to
remove your hairs from the front cover when the digitizer is still turned on.
Maintenance and Service:
• When the digitizer is going to be cleaned, ensure to turn off the power of each
device and unplug the power cable from the AC outlet.
• When you need a repair service, unplug the digitizer from the power outlet
and consult qualified service personnel.
• When replacement parts are required, use replacement parts that are specified
by the manufacturer or have the same characteristics as the original parts.
• For safety reasons, ensure to inspect the device before using it. In addition,
carrying out a regular inspection at least once a year.

MII-900 Plus User's Manual 7
Table of Contents
Preface ............................................................................................... 2
Safety Regulations ............................................................................. 3
FCC Compliance Statement ............................................................... 3
Regulations ..................................................................................... 4
Safety Precautions ........................................................................... 5
Knowing about Your Film Digitizer .................................................... 9
Features of the MII-900 Plus ............................................................. 9
System Requirements ..................................................................... 10
UnpackingYour Film Digitizer .......................................................... 11
Looking for Damage ....................................................................... 11
Unpacking Package Contents ........................................................... 11
Package Contents ........................................................................... 14
How to Repack Your Film Digitizer for Shipping ................................. 16
Taking a Closer Look ........................................................................ 18
Front / Top / Bottom View .............................................................. 18
Rear / Side View ............................................................................ 19
AssemblingYour Film Digitizer ........................................................ 20
Installing the Feed Tray .................................................................. 20
Installing the Output Tray ............................................................... 21
InstallingYour Film Digitizer ............................................................ 22
Installing the Software .................................................................... 22
Connecting the Film Digitizer ........................................................... 23
To the Power Cord ................................................................... 23
To the Hi-Speed USB Cable ...................................................... 23
Using Light Shield to Digitize Industrial RT X-ray Film ................... 25
Attaching Light Shield into Guide Arms ............................................ 25
Positioning Industrial RT X-ray Film with the Light Shield ................... 26
Scanning Industrial RT X-ray Films .................................................. 27

8 MII-900 Plus User's Manual
Using Film Holders to Digitize Industrial RT X-ray Film .................. 30
Positioning Your Industrial RT X-ray Film .......................................... 30
A. Using the 8.5" x 4.5" Film Holder ........................................ 30
B. Using the 12.5" x 3 1/3" Film Holder ................................... 31
Scanning Industrial RT X-ray Films .................................................. 32
Digitizing Industrial RT X-ray Films in Other Sizes ......................... 33
Positioning Industrial RT X-ray Film ................................................. 33
Scanning Industrial RT X-ray Films .................................................. 35
Care and Cleaning ............................................................................ 36
Cleaning the Glass Surface on the Digitizer ....................................... 36
Cleaning the Glass and Components on the Front Cover ..................... 37
Cleaning the Rollers ....................................................................... 39
Maintenance ..................................................................................... 39
Appendix .......................................................................................... 40
Fixing Film Jams ........................................................................... 40
Troubleshooting ............................................................................ 41
Specifications ................................................................................ 42

MII-900 Plus User's Manual 9
Knowing aboutYour Film Digitizer
The MII-900 Plus is a sheet-fed film digitizer, which is specifically designed for the
use of the RT X-ray film scanning. The MII-900XL can capture details in bright
and dark areas of industrial RT X-ray films and provide the professionals a
convenient method to digitize the physical originals for the electric data storage,
saving maintenance time and storage space enormously.
Features of the MII-900 Plus
The MII-900 Plus comes with several important features, including the following:
• Premium Image Quality — With a high resolution of 2400 dpi, a dynamic
range of 4.7 Dmax, and the 16-bit grayscale, the MII-900 Plus allows users
to get better image details in just seconds.
• Energy-saving LED light source — Adopting LEDs as the light source, when
the digitizer is detected by the system, there are no requirements for any
warm-up time before carrying out the scan, which boots your productivity and
reduces energy costs amazingly. With its stable performance, the image
quality will remain consistent even after used for a certain period of time.
• Support various sizes of X-ray films - The MII-900 Plus covers the scanning
of all standard RT X-ray film sizes from 2.5" x 2.5" to 14" x 52", which
offers more flexibility to digitize X-ray films.
• Exclusive Film Holders — These specially designed industrial film holders are
used to hold films in place. By loading industrial film holders with loaded films
before scanning, you can ensure perfect alignment of your scanned images
and achieve consistent scans. Two types of industrial film holders provided,
they are 8.5" x 4.5" and 12" x 3 1/3".
• Fast scanning speed — The MII-900 Plus increases your productivity with
fast scanning speed of 18 seconds or less at 300 dpi for a grayscale scan of
14" x 17" film.
• Hi-Speed USB (USB 2.0) port — Hi-Speed USB (USB 2.0) is capable of high
data transfer rates of up to 480 Mbit/sec.
• Easy to operate, clean and maintain — The MII-900 Plus requires virtually no
routine maintenance and no daily cleaning, which is ideal for radiographic
inspection industry.
• Microtek ScanWizard Industry software — The friendly user interface of
ScanWizard Medi converts X-ray films in a computer readable format, offering
an easy and quick access and management.
— Auto crop: This feature automatically crops the scan frame to fit the size
of the original film when scanning film with provided film holders.

10 MII-900 Plus User's Manual
— Auto density: This feature enables the digitizer to optimize the image
density automatically when scanning a X-ray film. It automatically defines
the lightest and darkest pixels in a scanned image and then redistribute
the intermediate pixel values proportionately.
— Customized exposure: This manual setting tool allows you to customize
an exposure time for the scanned image. It enhances the visibility of
extreme dark film, delivering a better scanning result and improving the
quality of saved files.
System Requirements
In order to use your MII-900 Plus, your computer must satisfy the following
system requirements:
• CD-ROM drive (for installing software)
• Color display with 24-bit color output capability
• 4GB RAM or more
• Pentium IV PC or higher with Hi-Speed USB (USB 2.0) port
• Windows XP, Windows 7 (64-bit) and Windows 8 (64-bit)

MII-900 Plus User's Manual 11
UnpackingYour Film Digitizer
Looking for Damage
While unpacking your digitizer, inspect the shipping carton for any signs of
mishandling or damage. The digitizer’s packing carton and padding material have
been carefully chosen to prevent damage to the unit in shipping and can withstand
a reasonable amount of pressure.
After unpacking your digitizer package, refer to the later section to ensure that you
received all of the parts necessary for digitizer setup. If there are any damaged or
missing parts, notify the shipper immediately or contact customer service.
NOTE: Save the carton and all packing materials. If you need to ship the digitizer
later, it is recommended that you should repack it using the original wire ties,
plastic bags, foam supports and cartons, which protects your digitizer from
unnecessary damage. Refer to the later section “How to Repack Your Film Digitizer
for Shipping” for the detail.
Unpacking Package Contents
After unpacking the shipping carton, follow the steps shown below to take out
your digitizer and other accessory components.
1. Ensure that you put your shipping carton
toward the right direction. Then, lift up the
top cover.

12 MII-900 Plus User's Manual
2. Remove each cardboard from four sides of
the shipping carton.
3. With both hands, hold the two sides of
foam supports and then lift up the foam
supports firmly from the carton. Before
putting down the package on a steady
surface, do not go off either of hands from
holding the foam supports.
Note: The package of the contents is heavy
(almost 33 pounds). Due to the heavy
weight of the package (about 33 pounds),
make sure you can handle it properly
before removing it from the carton.
4. Remove two accessory boxes (1 and 2)
from the foam supports.

MII-900 Plus User's Manual 13
5. Turn over the foam supports and make
them stand vertically.
6. Lift up the upper foam support.
7. Pull out the digitizer from the bottom
foam support. Then, remove the digitizer
from the wrapped plastic bag.

14 MII-900 Plus User's Manual
Power Cord
Hi-Speed USB Cable
CD
Package Contents
After you have unpacked your digitizer package, please check for the major
components listed below.
MII-900 Plus Film Digitizer
Accessory Box 1
Feed Tray
Output Guide
Accessory Box 2
Accessories for Box 1

MII-900 Plus User's Manual 15
Output Basket
Accessories for Box 2
8.5" x 4.5" Holder
12.5" x 3 1/3
Holder

16 MII-900 Plus User's Manual
How to Repack Your Film Digitizer for
Shipping
To ship back your MII-900 Plus for repairing, maintenance services, or other
reasons, in order to not damage your MII-900 Plus, it is strongly recommended
that using the original carton and other packing materials. Follow the steps below
to repack your MII-900 Plus correctly.
1. Wrap the digitizer with the plastic bag, and
then insert it into one foam support.
2. Cover down the other foam support on the
tops of the digitizer.

MII-900 Plus User's Manual 17
3. Turn over the foam supports and insert
other two accessory boxes into the both
sides of the foam supports.
4. With both hands, hold the two sides of
foam supports firmly and then insert them
into the shipping carton.
5. Close the top cover of the shipping
carton and seal it with tape.

18 MII-900 Plus User's Manual
Taking a Closer Look
Front / Top / Bottom View
No. Names of Parts Functions of Parts
1 Feed Tray Holes Uses to hook the Feed Tray onto the digitizer.
2 Power Switch Turns the digitizer on or off.
3 Fastenings of Light Shield Uses to fasten the Light Shield into Guide Arms on the Input Tray.
4 Hook of Light Shield Uses to pull the Light Shield up.
5 Front Cover Uses to cover inner components of the digitizer.
6 Green/Orange LEDs Indicates the status of the digitizer. For more details, refer to the
“Troubleshooting” section of this manual.
7 Output Tray Holes Uses to hook either the Output Guide or the Output Basket onto the
digitizer.
8 Release Buttons Releases the front cover to open the lamp holder. There are two
Release buttons located on each side of the front cover. Press the
buttons down simultaneously to release the front cover.

MII-900 Plus User's Manual 19
No. Names of Parts Functions of Parts
1 Hi-Speed USB Port Connects the Hi-Speed USB (USB 2.0) cable to the computer.
2 Power Connector Connects the digitizer to the power cord.
Rear / Side View

20 MII-900 Plus User's Manual
AssemblingYour Film Digitizer
Installing the Feed Tray
Coming with your digitizer, there is a separated Feed Tray which holds the X-ray
films to be fed into the digitizer. Before using the Feed Tray with your digitizer,
you need to assembly it onto the digitizer.
Follow the instructions and graphs below to correctly install the Feed Tray.
Feed Tray
Feed Tray Holes
1. Look for two sets of the Feed Tray
Holes at both ends of the front-top of
the digitizer.
2. Insert and push down both sides of
the Feed Tray into its compartment
holes, making sure the Feed Tray
snaps into place.