Midas Touch MPL-1000 User guide

Fingerprint Identification Padlock
MPL-1000
Quick Operation Guide
V1.2

1
Important information:
Please read this claims, before using this product
Limited warranty:
This warranty stated herein shall NOT apply, if: (1) this Product has not been used in
accordance with any accompanying instructions, (2) this Product has not been used for its
intended functions and environment, (3) the artificial malicious damage or personal
negligence cause any defects, (4) if this Product has been opened, modified or repaired by
anyone other than an authorised service centre, or if it is repaired using unauthorised spare
part; Or because of an accident or other external factors causing any malfunction or defects.
To use this Product in the above manner or the similar way, which will be at your own risk.
Warranty service:
1. Please make the stamp of distributor and fill in the date of purchase on the
bottom of this page, as your warrantycard.
2. Offer one year limited warranty service for the product used under the normal
operation and environment. (Product accessories , User manual are not in
warranty range)
3. In case of improper using (such as oil or other fluids, gets wet, drops, pinched or
places in the abnormal temperature and humidity) or the artificial destruction,
disasters causes the damages, would be the exclusion of warranty.

2
Appearance and function introduction:
Charge the battery:
Open the USB cover, then plug in the Micro USB cable connected to the external power
supply (as Figure 2) and keep the connector tightly connected. The following three
cases need to charge the battery:
(1) The first time use MPL-1000
(2) When the battery capacity has reached the warning status of low battery (the red
LED flashes 5 times which occurs in fingerprint scanning mode)
(3) When the battery capacity is unable to start MPL-1000, charging, just like
an emergency power supply for emergency unlock
 Low battery status: red LED flashes 5 times
 Charging: red LED lights up
 Full charging: red LED turns off
Figure 2

3
 MPL-1000 implements the lithium-polymer battery, we
recommend charging at any time in order to maintain MPL-1000
operations
 When battery capacity is low, it should be charged as soon aspossible
to avoid battery runs out
 In the case is not used or not charging for a long time,
recommendations should be charged each month, avoiding battery
runs out
Unlock:
There are two ways to unlock:
(1) In the locked state, press the shackle of MPL-1000 once (as Figure 3) to activate
MPL-1000 and then the green LED lights up and begins flashing (flashing time about
5 seconds, but in case the battery capacity reaches the low level, the red LED will
light up and flashing 5 times). Now this status is fingerprint scanning mode. At this
state,
please press any fingers in the sensor (as Figure 4) to unlock MPL-1000, the green
LED lights up and a beep sounds; then you can unlock the shackle by slide button
(as Figure 5).
(2) In fingerprint scanning mode, you must press the valid fingerprint in the sensor to
unlock after you have successfully enrolled your fingerprints (the detail procedures
please refer to the fingerprint enrollment) in MPL-1000, and green LED lights up and
a beep sounds, then you can unlock the shackle by slide button (as Figure 5).

4
 Fingerprint scanning mode: green LED lights up and begin flashing for
about 5 seconds
 Unlock: green LED lights up for about 5 seconds a beep sounds
 The first time you use MPL-1000, we recommend to
immediately complete the fingerprint enrollment
 MPL-1000 will be powered off automatically if no any operations
happen till green LED turns off which the fingerprint scanning mode
or unlock phase
 All procedures have the time constraints, please follow the provisions
in operation guide
 Unlock failure: red LED continuously lights up for about 2 seconds
4 beeps sound

5
Lock:
In unlocked state, pressing the shackle once (as Figure 3) to lock MPL-1000
immediately, the red LED lights up for about 2 seconds and two beeps sound at the
same time. And then MPL-1000 will be powered off automatically.
 Unlock: green LED lights up for about 5 seconds a beep sounds
 lock: red LED lights up for about 2 seconds two beeps sound
 All procedures have the time constraints, please follow the provisions
in operation guide
Fingerprint enrollment:
(1)Please follow the unlock procedures to enter unlock state, (green LED will
continuously lights up for approximately 5 seconds, which is the important period
for entering fingerprint enrollment) at the moment, continuously press and hold
shackle until the red and green LED interactive flash and heard a beep sound.
(2) Now, you can press your finger onto the fingerprint sensor to scan your fingerprints
before the red, green LED interactive flashing turn off (this available time is
approximately 5 seconds, as Figure 6). When your fingerprint is successfully scanned,
MPL-1000 will sound a beep and green LED light up once, you can remove your
finger.
(3) Repeat step (2) until you hear a long beep, this means your fingerprint has
successfully been enrolled into MPL-1000. Each finger must be done at least 7 times
for the input of the fingerprintcharacteristics.
(4) Each finger enrolled completely and successfully, and then the red and green flash

6
interactively again; repeat steps (2) ~ (3) to register other fingerprints. If you wanna

7
exit enrollment mode, press the shackle once directly. MPL-1000 can store up to
30 sets of fingerprints, In case the fingerprints accumulation of a total reaches 30,
MPL-1000 will sound 5 beeps and the red LED lights up approximately 5 seconds,
and then automatically returns to enrollment mode.
(5) In enrollment mode, when you press shackle once directly or there is no any
operations within 5 seconds, MPL-1000 will sound 2 beeps and automatically
power off.
Figure 6
 Fingerprint enrollment mode: red and green LED alternately
flashing for approximately 5 seconds one beep sound
 Complete each valid fingerprint enrollment must use the same
fingerprint and at least 7 times for the input of the fingerprint
characteristics
 Scan the fingerprint, it should be as far as possible to cover theentire
sensor
 MPL-1000 stores up to 30 sets of fingerprints: red LED lights up
for about 5 seconds 5 beeps sound
 In enrollment status, press shackle once directly or no any inputs
within 5 seconds, MPL-1000 will sound 2 beeps and

8
automatically

9
power off.
 All procedures have the time constraints, please follow the provisions
in operation guide
 MPL-1000 stores up to 30 sets of fingerprints, it can nolonger
enroll fingerprint
 Children's smaller fingers, which can not be effectively covered in
fingerprint sensor to failure in recognition, it is not recommended for
children to enroll fingerprints
Clear all Fingerprints:
In fingerprint enrollment phase, press the shackle and hold until the red LED lights up
and then hear a long beep (this period is approximately 2 seconds), then release the
shackle. Now, all fingerprints has been cleared, and then MPL-1000 will exit the
enrollment phase and automatically power off.
 Fingerprint enrollment phase: red and green LED alternately
flashing for approximately 5 seconds one beep sound
 All procedures have the time constraints, please follow the
provisions in operation guide