Middle Atlantic Products MMB-1X1-12C User manual

Clamp Mounting (FIGURE A)
1) Slideknob on to bolt (short bolt), ensuring the bolt
head is securely engaged into the knob.
2) Screw boltin to the lower clamp bracket and press clamp
pad on to the threaded end of thebolt.
3) Hook lower clamp bracket into one of the top 2 (of the3)
positions provided.
4) Position clamp bracket and pole assembly onto work
surface in desired location.
NOTE: Upper clamp bracket must contact edge
of work surface.
5) Using knob tighten pole base assembly securely
to work surface.
MMB-1X1-12C Monitor Mount
Instruction Sheet
I-00693 Rev A
Grommet Mounting (FIGURE B)
1) Use Phillips screwdriver to remove two (2) screws which
attach the upper clamp bracket to pole base.
2) Assemble lower clamp bracket to furthest slots on
upper clamp bracket to align clearance holes.
3) Slide knob onto bolt (long bolt).
4) Lay monitor cables through grommet holes in the work
surface.
5) Align pole on work surface.
6) Install boltthrough the clearance holes onclamp
bracket. Insert the threaded end through the grommet
and screw into the pole base, using knob to tighten
pole base assembly securely to work surface.
FIGURE A
FIGURE B
MOUNTING BASE
REFER TO PARTS LIST ON PAGE 3
Pole Base Assembly
Clamp Pad
Lower Clamp
Bracket
Knob
Short Hex Bolt
Upper Clamp Bracket
Long Hex Bolt
(2) Phillips Flat Head Screws
Upper Clamp Bracket
Lower Clamp Bracket
Knob
Pole Base Assembly

Page 2
Pole Base Assembly
Arm
Support
Ring
Pole Joint
Bushing
Trim Ring
Monitor Mount
Knuckle
MONITOR MOUNT ATTACHMENT (FIGURE D)
FIGURE D
Cable Management Clips
1) Slide arm support ring onto pole at desired height
and lock into place.
2) Snap pole joint bushing into monitor mount knuckle
(may already be inside monitor mount knuckle).
3) Slide monitor mount knuckle onto pole.
4) Snap trim ring onto monitor mount knuckle.
5) Insert cables into cable management clips.
(2) Phillips Flat Head Screws
Upper Clamp Bracket
Pole Base Assembly
Pole Base Assembly
Knob
Short Hex Bolt
L5 Lectern Mounting (FIGURE C)
of the existing factory drilled 1/2” pilot hole locations.
2) Use Phillips screwdriver to remove two (2) screws which
attach the upper clamp bracket to pole base.
3) Slide knob onto bolt (short bolt).
4) Position pole base assembly over drilled hole on work surface.
5) Install boltthrough the clearance hole inworksurface into
threaded hole on pole base. Using knob, tighten pole base
assembly securely to work surface.
1) From bottom of worksurface, drill a 1/2” dia hole using one

Quick Connect
VESA Mount
Screw Kit
(Qty 4 Short, 4, Long)
Pole Base
Assembly
With Upper
Clamp Bracket
Pole Joint Bushing Arm Support Ring Trim Ring
Monitor Mount
Knuckle
Knob Clamp Pad
PARTS LIST
3/8-16 Hex Bolts
(1) Short 3-1/2”LG
(1) Long 5-1/2”LG
Lower Clamp
Bracket
Quick
Connect
VESA
Mount
Monitor Mount
Knuckle
Screws (4)
1) Attach quick connect vesa mount to monitor
using the appropriate screws (short or long).
2) Slide quick connect bracket onto monitor
mount knuckle until it clicks into place.
3) Depress tab on base of quick connect
bracket to release from mount.
NOTE: Adjusting the Tilt Tension:
If the monitor drops or is too tight, adjust the
tension screw at the side of the head as
shown using the 3/16” hex key.
(1) 3/16” Hex Key
(1) 1/8” Hex Key
Page 3
MONITOR ATTACHMENT (FIGURE E)
FIGURE E

Page 4
WARRANTY
Middle Atlantic Products, Inc. (the "Company") warrants the MMB-1X1-12C Monitor Mount to be free from defects in material or
workmanship under normal use and conditions for a period of (3) years from date of shipment by the Company.
The Company's entire liability to the purchaser, and the purchaser's (or any other party's) sole and exclusive remedy, under this warranty
shall be limited, at the Company's option, to either (a) return of and refund of the price paid for, or (b) repair or replacement at the
Company's factory of the products purchased, or any part or parts thereof, which the Company has determined to be defective after
inspection thereof at the Company's factory.
This warranty does not cover damage due to acts of God, accident, misuse, abuse or negligence by parties other than the Company, or
any modification or alteration of the products. In addition, this warranty does not cover damage due to improper handling, assembly,
installation or maintenance.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL THE COMPANY BE LIABLE FOR ANY
SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION,
DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF
THE USE OF THE PRODUCTS PURCHASED, EVEN IF THE COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. THE COMPANY'S LIABILITY TO THE PURCHASER (OR ANY OTHER PARTY) HEREUNDER, IF ANY, SHALL IN NO
EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCTS PAID TO THE COMPANY.
Corporate Headquarters
Corporate Voice 973-839-1011 - Fax [phone] / International Voice [phone] - Fax [phone]
middleatlantic.com - [email protected]
Middle Atlantic Canada
Voice 613-836-2501 - Fax [phone] / middleatlantic.ca - [email protected]
Factory Distribution
USA: NJ - CA - IL Canada: ON - BC
At Middle Atlantic Products we are always listening. Your comments are welcome.
Middle Atlantic Products is an ISO 9001 and ISO 14001 Registered Company.