Middle Atlantic Products VDM Series User manual

I-00807 Rev A
VDM Series
FIXED & TILT WALL MOUNT
Instruction Sheet
Thank you for purchasing a Vision Display fixed or tilt wall mount.
Please read these instructions thoroughly before installing or assembling these products.
PRODUCT FEATURES
THANK YOU
• Open wall plate design maximizes accessibility to connections and cable pass-through behind
the display
• Post-install leveling mechanism enables quick micro-adjustment of horizontal plane of display
• Safety locking features keep the display securely mounted
• VESA Capability:
VDM-400-F & VDM-400-T 75x75mm - 400x400mm
VDM-600-T & VDM-600-T 75x75mm - 600x400mm
VDM-400-F & VDM-600-F VDM-400-T & VDM-600-T

IMPORTANT SAFETY INSTRUCTIONS / INSTRUCTIONS IMPORTAANTES SUR LA SÉCURITÉ
SAVE ALL INSTRUCTIONS / CONSERVER CES INSTRUCTIONS
CAUTION/ATTENTION and the exclamation point within an
equilateral triangle is intended to alert the user to the possibility of
damaging or destroying the equipment if the instructions are not
followed.
Attention et le point d'exclamation dans un triangle équilatéral est
destiné à alerter l'utilisateur de la possibilité d'endommager ou de
détruire l'équipement si les instructions ne sont pas suivies.
WARNING/AVERTISSEMENT and the exclamation point within an
equilateral triangle is intended to alert the user to the possibility of
serious injury or death if the instructions are not followed.
Avertissement et le point d'exclamation dans un triangle équilatéral
est destiné à alerter l'utilisateur de la possibilité de blessures
graves ou la mort si les instructions ne sont pas suivies.
Page 2
WARNING: Failure to read, understand and follow the following information can result in seri-
ous personal injury, damage to the equipment or voiding of the warranty.
AVERTISSEMENT: Ne pas lire, comprendre et suivre les informations suivantes peut entraîner
des blessures graves, des dommages à l'équipement ou de la nullité de la garantie.
WARNING: Failure to provide correct structural strength for the component may result in seri-
ous personal injury or damage the equipment. The 2x4 stud wall to which the component is
being attached may have a maximum drywall thickness of 5/8” (1.6 cm).
AVERTISSEMENT: Le défaut de fournir une résistance structurelle correcte pour le composant
peut entraîner des blessures graves ou endommager l'équipement. Le goujon de 2x4 auquel le
composant mur est connecté peut avoir un maximum de 1.6 cm (5/8”) d'Épaisseur cloison
sèche.
WARNING: Exceeding the weight capacity may result in personal injury or equipment damage.
The combined weight of all components attached to the mount must not exceed weights listed
on page 3.
AVERTISSEMENT: Dépasser la capacité de poids peut entraîner des blessures ou des dom-
mages matériels. Le poids combiné de tous les composants reliés au support de montage ne
doit pas dépasser les grammages indiqués à la page 3.
WARNING: Be aware of pinch points and do not place fingers in between moving parts.
AVERTISSEMENT: Soyez conscient des points de pincement et de ne pas placer les doigts
entre les pièces mobiles.
WARNING: Use this product for its intended use and only use attachments recommended by
the manufacturer.
AVERTISSEMENT: Utilisez ce produit pour son utilisation prévue et utiliser uniquement les
accessoires recommandés par le fabricant.
WARNING: Do not use a damaged product. Return damaged products to a qualified service
center for repair.
AVERTISSEMENT: Ne pas utiliser un produit endommagé. Retour produits endommagés à un
centre de service qualifié pour la réparation.
WARNING: Not intended for outdoor use.
AVERTISSEMENT: Non destiné à une utilisation en extérieur.

Page 3
WEIGHT RATINGS
Model Weight Rating
VDM-400-F 150 lbs. Maximum Total Rated Load
VDM-400-T 150 lbs. Maximum Total Rated Load
VDM-600-F 180 lbs. Maximum Total Rated Load
VDM-600-T 180 lbs. Maximum Total Rated Load
• #2 Phillips Screwdriver
• Drill
• Protective Eyewear
• 7/32” Wood Bit or 7/16“ Masonary Bit
• Level
• Hammer
• 1/2” Hex Socket
TOOLS REQUIRED
WARNING: Use tools with caution and follow all necessary safety protocols.
AVERTISSEMENT: Utiliser des outils avec prudence et suivre tous les protocoles de sécurité
nécessaires.
SUPPLIED COMPONENTS
(1)
Wall Mount Bracket
(A)
(2)
Fixed Display
Mount Brackets
VDM-400 & -600-F
MODELS ONLY
(B)
(2)
Tilt Display
Mount Brackets
VDM-400 & -600-T
MODELS ONLY
(C)

(4)
Hex Head Screw
(D)
(4)
Wall Anchor
(E)
Page 4
COMPONENTS SUPPLIED (CONTINUED)
(4)
M4 x 20
(M-C)
M5 x 30
(M-G)
M6 x 20
(M-J)
M6 x 30
(M-K)
M5 x 12
(M-D)
(4)
(4)
M6 x 12
(M-H)
(4)
(4) (4)
M4 x 12
(M-A)
Display Mount Screws
(4)
M6 Long Spacer
(J)
(4)
M8 Long Spacer
(L)
(12)
M8 Washer
(F)
M8 x 16
(M-L)
(4)
M8 x 20
(M-M)
(4) (4)
M8 x 40
(M-N)
(4)
M5 Washer
(G)
(4)
M4 x 16
(M-B)
M5 x 16
(M-E) M5 x 20
(M-F)
(4)
(4)
(4)
Display Mount Spacers
(4)
M8 Short Spacer
(K)
(4)
M6 Short Spacer
(H)
(1)
Proximity Mounting
Plate Kit
(P)

WOOD STUD WALL BRACKET INSTALLATION
Page 5
1. Determine height for display and find center of stud closest to desired position on wall. Locate the center of
the second stud to the left or right of desired location.
2. Using a level, scribe a 10” long line down the center of both studs at the desired height. (FIGURE A)
FIGURE A
3. Using a level and the wall mount bracket (A) as a template, mark the center of the 4 mounting holes in line
with the scribed center line of each stud. (FIGURE B)
Mounting slots
4. Remove wall mount bracket and using a 7/32” drill bit, drill a 2.5” deep pilot hole in each of the 4 marked
center points.
A
FIGURE B

WOOD STUD WALL BRACKET INSTALLATION CONT.
Page 6
1) Install wall mounting bracket (A) using (4x) hex head screw (D) and (4x) washer (F). (FIGURE C)
BLOCK OR CEMENT WALL BRACKET INSTALLATION
1. Determine position and height for display. Using a level and the wall mount bracket (A) as a template, mark
the center of the 4 mounting slots that are spaced the farthest apart. (FIGURE D)
FIGURE D
A
D
F
A
Mounting slots
FIGURE C

BLOCK OR CEMENT WALL BRACKET INSTALLATION CONT.
Page 7
2. Remove wall mount bracket and using a 7/16” drill bit, drill a 2.5” deep hole in each of the 4 marked
center points. (FIGURE E)
3. Press a wall anchor (E) into each of the 4 drilled holes.
4. Install wall mounting bracket (A) using (4x) hex head screw (D) and (4x) washer (F). (FIGURE F)
FIGURE E
E
A
D
F
FIGURE F
NOTE: Wall anchors may
require a hammer
to install.
NOTE: To prevent anchors from
stripping, only use a hand
tool to install.

Page 8
STOP
These display mounts are supplied with a Proximity Series
Mounting Plate PRX-MP-9X12. Before installing display
mounting brackets to your display, follow the supplied
mounting plate installation instructions I-00804 to find the best
location for mounting your plate.

DISPLAY MOUNT BRACKET INSTALLATION
Page 9
1. Using supplied display mount screws, select the appropriate screw size and length ensuring screw does not
bottom out in mounting hole, or damage to display may occur. If you feel resistance, stop immediately and try
a shorter screw. If supplied screws are still too long, use supplied spacers to take up slack.
2. Align display mount bracket (B or C) with mounting holes on the back of display. Using (4x) display mount
screws (M-A - M-N) to secure the Display Mount to your display. (FIGURE G)
TV
TV
TV TV
B or C
FIGURE G
M-A - M-N
F or G
B
C

RECESSED OR RAISED BACK DISPLAY MOUNT BRACKET INSTALLATION
Page 10
1. Using supplied display mount screws, select the appropriate screw size and length ensuring screw does not
bottom out in mounting hole, or damage to display may occur. If you feel resistance, stop immediately and try
a shorter screw. If supplied screws are still too long, use supplied spacers to take up slack.
2. Align display mount bracket (B or C) with mounting holes on the back of display. Using (4x) display mount
screws (M-A - M-N), (4x) washers (F or G) and (4x) spacers (H - L) to secure the display mount bracket to
your display. (FIGURE H)
B or C
FIGURE H
H - L
F or G
B
C
M-A - M-N
TV
TV
TV TV

HANGING DISPLAY (FIXED MOUNT)
Page 11
1. Tilt display and hook display bracket onto flange of wall mount bracket (A). Standoff support may be used to
prevent display from locking into place while connecting wires. (FIGURE J)
2. Swing standoff support up to lower display in place. push along the bottom of display until the mount
clicks into place. (FIGURE K)
3. To remove display from the wall bracket, pull both release cord rings down while pulling bottom of display
away from wall and lift display off flange of wall mount bracket. (FIGURE L)
Release Cord
FIGURE J FIGURE K FIGURE L
Standoff Support
4. Once installation is complete, use level adjustment screws on top of display mount brackets to level display.
After display is level, screw in both display lock screws on bottom of brackets to secure display to wall
mount. (FIGURE M)
Leveling Screws
Display Lock Screws
FIGURE M

HANGING DISPLAY (TILT MOUNT)
Page 12
1. Tilt display and hook onto flange of wall mounting bracket. (FIGURE P)
2. Push along the bottom of display until the mount clicks into place. (FIGURE R)
3. To remove display from the wall mount bracket, pull both release cord rings down while pulling bottom of
display away from wall. Lift display off flange of wall mount bracket. (FIGURE S)
Release Cord
FIGURE P FIGURE R FIGURE S
4. Once installation is complete, use level adjustment screws on top of display mount brackets to level display.
After display is level, screw in both display lock screws on bottom of brackets to secure display to wall
mount bracket. (FIGURE T)
Leveling Screws
Display Lock Screws
FIGURE T

ADJUSTING DISPLAY TILT (VDM-400-T & VDM-600-T ONLY)
Page 13
1. To tilt display, loosen wing screws on both display mount brackets.
2. Grab top and bottom of display and carefully pull top of display gently to desired angle. Tighen both wing
screws to lock display at desired angle.
3. To return display to a vertical position, loosen both wing screws and grab top and bottom of display ,carefully
push display from the top. Tighten wing screws to lock in position.
+15°/-5°
Wing Screw
NOTE: Wing screw is spring loaded to allow you
the ability to reposition wing when loosening and
tightening mount. To reposition, pull wing out and
reposition.

Page 14
For warranty information, refer to www.middleatlantic.com/terms.
Corporate Headquarters
Corporate Voice: 973-839-1011 - Fax: [phone] / International Voice: [phone]
Fax: [phone]
www.middleatlantic.com - [email protected]
Middle Atlantic Canada
Voice: 613-836-2501 - Fax: [phone]
ca.middleatlantic.com - [email protected]
Factory Distribution
USA: NJ - CA - IL Canada: ON - BC
At Middle Atlantic Products we are always listening. Your comments are welcome.
Middle Atlantic Products is an ISO 9001 and ISO 14001 Registered Company.
WARRANTY