Midea CCM-18A/N User manual

Thank you very much for purchasing our product.
Before using your unit, please read this manual carefully and keep it for future reference.
Modbus Gateway Operation Manual
Applicable models˖CCM-18A/N
.......................................................................................1
.........................................................................2
......................................................................................4
...........................................................................................12
................................................................. 12
Warning
Caution
Warning
Usage
Warning

.......................................................................................1
.........................................................................2
......................................................................................4
...........................................................................................12
................................................................. 12
Warning
Caution
Warning
Usage
Warning

Safety precautions.......................................................................................1
.......................................................................................1
Overview ......................................................................................................2
.........................................................................2
Usage introduction......................................................................................4
......................................................................................4
Software reset ...........................................................................................12
...........................................................................................12
appendix˖ljmapping tableNJ................................................................. 12
................................................................. 12
Contents
Warning
Caution
Warning
Usage
Warning

1
.......................................................................................1
.........................................................................2
......................................................................................4
...........................................................................................12
................................................................. 12
1. Safety precautions
The following contents are stated on the product and the operation
manual, including usage, precautions against personal harm and
property loss, and the methods of using the product correctly and safely.
After fully understanding the following contents (identifiers and icons),
read the text body and observe the following rules.
 Identifier description
Identifier Meaning
Means improper handling may lead to
personal death or severe injury.
Means improper handling may lead to
personal injury or property loss.
[Note]: 1. “Harm” means injury, burn and electric shock which need
long-term treatment but need no hospitalization
2. “Property loss” means loss of properties and materials.
W
arning
arning
Caution
Caution
 Icon description
Meaninglcon
It indicates forbidding. The forbidden subject-matter is
indicated in the icon or by images or characters aside.
It indicates compulsory implementation. The compulsory
subject-matter is indicated in the icon or by images or
characters aside.
Warning
W
arning
arning
Please entrust the distributor or professionals to install
the unit. The installers must have the relevant know-how.
Improper installation performed by the user without perm
ission may cause fire, electric,shock, personal injury or w
ater leakage.
Delegate
installation
Forbid
Forbid
Usage
Usage
W
arning
arning
Do not spray flammable aerosol to it directly.
Otherwise, fire may occur.
Do not operate with wet hands or let water enter it .
Otherwise, electric shock may occur.

2
.......................................................................................1
.........................................................................2
......................................................................................4
...........................................................................................12
................................................................. 12
Warning
Caution
Warning
Usage
Warning
2 Overview
2.1 Instruction
Fig.2.1
WAN terminal˖Connect to the switche by 5 kinds of network cables to ensure that
PC can access to the web page of it.
A1B1E terminal˖Connect to the indoor/outdoor unit
A2B2E terminal˖Connect to the terminal serial port.
2.2 System Architecture Description
It supports two kinds of outdoor unit with baud rates of 600 and 4800. (For detailed
information, please contect our technical support). The addresses of accessed
indoor/outdoor units can’t repeat.
1)When the baud rate of the outdoor unit is 600, 64 indoor units and 4 outdoor units
can connect to it at most.
2) When the baud rate of the outdoor unit is 4800, 60 indoor (with the address from
4—63) units and 4 outdoor units can connect to it at most.
The upper computer system with Modbus protocol access to terminal A2B2E by RTU
or by TCP to connect to modbus gateway. See the connection figure between
modbus gateway and air-conditioner system below:
Connection through Modbus TCP:
Note:XYE port and K1K2E port connect hand in hand,and then access to
A1B1E port.
:$1
A1
B1
E
A2
B2
E
POWER
RESET
,3
32:(5


3
.......................................................................................1
.........................................................................2
......................................................................................4
...........................................................................................12
................................................................. 12
Warning
Caution
Warning
Usage
Warning
Fig.2.2
Fig.2.3
Connection through Modbus RTU:
Ｍｏｄｂｕｓ ｓｙｓｔｅｍ
Ｍｏｄｂｕｓ ＴＣＰ
ＸＹＥ
Ｋ１Ｋ２Ｅ
Ｍｏｄｂｕｓ ｓｙｓｔｅｍ
Ｍｏｄｂｕｓ ＲＴＵ
ＸＹＥ
Ｋ１Ｋ２Ｅ

4
.......................................................................................1
.........................................................................2
......................................................................................4
...........................................................................................12
................................................................. 12
Warning
Caution
Warning
Usage
Warning
2.3 Function Code
Function code
0x01
0x04
0x10
Function name
Read Coils
Read Input Register
Write Holding Register
Function
Read
Read
Write
Code
0x 01
0x02
0x03
0x06
Name
Illegal function code
Illegal data address
Illegal data
Slave busy
2.4 Abnormal Reply
The master unit sends requests and waits for reply from the slave.When there’s no
error occurs, the slave will reply normally, but when there’s data checking error, the
slave won’t answer. When the master unit sends wrong data (except for checking
error), the slave will answer abnormally.
Meaning
Function code received by the
slave can’t be executed.
The received data address is
not allowed.
Value in query data field is not
allowed by the slave
The slave is busy with a long-time
program command. Ask the
master to send messages when
the slave is free.
3 Usage Introduction
3.1 IP Configuration
The default IP address is 192.168.1.200 when modbus gateway leaves the factory.
The PC used for visiting websites must be in the same subnet segment with
modbus gateway, which means it should be 192.168.1.xx (xx is from 2 to 254).
There are 2 ways to configure IP: static configuration and multi-IP addition
3.1.1 Single IP Configuration
Open protocol dialog, configure the IP address and subnet mask, for example: IP:
192.168.1.211, subnet mask 255.255.255.0

5
.......................................................................................1
.........................................................................2
......................................................................................4
...........................................................................................12
................................................................. 12
Warning
Caution
Warning
Usage
Warning
Fig.3.1
Fig.3.2
After setting, click “OK” button.
3.1.2 Multi-IP Addition
Configure a static IP address before adding multiple IP.
Open protocol dialog and choose Advanced tab. TCP/IP setting dialog will display
like below:

6
.......................................................................................1
.........................................................................2
......................................................................................4
...........................................................................................12
................................................................. 12
Warning
Caution
Warning
Usage
Warning
Fig.3.3
Click “Add” in IP address bar to add an IP address which is in the same segment as
“192.168.1.200”, e.g., IP: 192.168.1.209ˈsubnet mask 255.255.255.0ˈand click “OK”
3.2 Configuration
Input http://192.168.1.200 in the address bar in IE (suggest to use IE). Choose
“Configuration” when web page of modbus gateway displays, as shown below:
Parameters Setting:
Parameter Description
Modbus address
Modbus commu-
nication setting
IP address
Subnet Mask
Gateway
Baud rate of the
outdoor unit
Modbus ID, to distinguish modbus gateway with multiple
Modbus protocols in the same subnet. Don’t repeat the address.
Baud rate: suggest 9600˗
Check bit: no checking by default
Stop bit: 1StopBit by default
IP address of modbus gateway, multiple IPs can’t be the same.
Default˖255.255.255.0
Local gateway address
Outdoor communication baud rate which is connected to
modbus gateway
Click “Application Settings” after changing the corresponding parameters. Click “Get
Settings” when apply the new settings. Modbus gateway will restart automatically
after changing settings, the network will break and reconnect.

7
.......................................................................................1
.........................................................................2
......................................................................................4
...........................................................................................12
................................................................. 12
Warning
Caution
Warning
Usage
Warning
Fig.3.4
3.3 Air Conditioner Information Query
Choose “power winding” or “input register” in the web page to read information of
the air conditioner unit.
When choose “power winding” it will be like the picture below.
When click the address number of the indoor or outdoor unit, it will show correspond-
ing operation information of the air conditioner. The chosen device will display in the
red frame.
When click “input register”, the interface will be like this:

8
.......................................................................................1
.........................................................................2
......................................................................................4
...........................................................................................12
................................................................. 12
Warning
Caution
Warning
Usage
Warning
Fig.3.5
The first column is the address, second is the content and the third is displayed
value, e.g. 17/0011, 17 is decimal display, 0011 is hexadecimal display.
Explanation of part of the content:
E.g., outdoor unit on-line state: 1/0001. When No. 0 outdoor unit is on-line, its value
is 1/0001(decimalism / hexadecimal ), when No.0 outdoor and No. 1 outdoor unit
are on-line, its value is 3/0003.
Air Conditioner Control
When click “Air Conditioner Control” on the web page, it will display like this:

9
.......................................................................................1
.........................................................................2
......................................................................................4
...........................................................................................12
................................................................. 12
Warning
Caution
Warning
Usage
Warning
Fig.3.6
Single air conditioner control area: control the single air conditioner. Choose a single air
conditioner and set mode, wind speed and temperature.
Single control area: to choose a single air conditioner, set mode, wind speed, temperature
and click “Apply” to carry out a single controlling function.
Group control area: to choose the corresponding group control button and carry out group
controlling. All the indoor units under the control of modbus gateway carry out this
operation.
Single Air
Conditioner
Control Area
Group control
of cooling
system

10
.......................................................................................1
.........................................................................2
......................................................................................4
...........................................................................................12
................................................................. 12
Warning
Caution
Warning
Usage
Warning
3.4 Upper Computer Access
3.4.1 Upper Computer Access Mode
Upper computer system with Modbus protocol port can communicate with modbus
gateway through Modbus TCP or Modbus RTU. For detailed information, please
refer to Fig .2.2 and Fig. 2.3.
3.4.2 Access to Debug
Via Modbus Poll software to access debugging. Here is the debug
procedure:
3.4.2.1 Install Modbus Poll software
When finish installing Modbus Poll software, the home page will display like this:
Fig.3.7
Fig.3.8
3.4.2.2 Connect Modbus Gateway
There’re 2 connection ways: Modbus TCP and Modbus RTU
1)Choose ”Connection”->”Connection” in figure 3.7,and then chose TCP/IP in the
pop-up window:
To choose a
connection
way
IP address for
connection
Connection terminal:
502 by default

11
.......................................................................................1
.........................................................................2
......................................................................................4
...........................................................................................12
................................................................. 12
Warning
Caution
Warning
Usage
Warning
Fig.3.9
Click “OK” when finish setting.
2˅Connection through Modbus/RTU
Choose RTU to connect, as shown below:
To PC port
In accordance
with the settings
of Modbus on
web page.
3.4.2.3 Test
Modbus Poll software can read/write the content of corresponding address in
mapping table.
Take reading coil content for an example:
Choose “Poll Definition” under “Setup”
Modbus address
Initial address
needed to check
Address length
Click the "OK" button and it will display the content. If the content is the same
as the value of the web page which has the same address, it means that the
software debugging success.

12
.......................................................................................1
.........................................................................2
......................................................................................4
...........................................................................................12
................................................................. 12
Warning
Caution
Warning
Usage
Warning
4 Software Reset
Press"RESET" button on the gateway for 3 seconds and power on again, the
software configuration will be back to the original setting.
5 AppendixljMapping TableNJ
Take writting holding register for example:
Choose button in Fig.3.7,as shown below:
After changed the value,click “send” button to finish the writting operation.
 
Modbus
KROGLQJUHJL
FKDQJHWKHYDOXH
VWHUDGGUHVV
address


0',8':
.......................................................................................1
.........................................................................2
......................................................................................4
...........................................................................................12
................................................................. 12
Warning
Caution
Warning
Usage
Warning

ᵢ䈪᱄Ҝ㿺Ṳφ[Ƚ
唇ⲳᢉদ
ᵢ享уᢉদ
.......................................................................................1
.........................................................................2
......................................................................................4
...........................................................................................12
................................................................. 12
Warning
Caution
Warning
Usage
Warning

.......................................................................................1
.........................................................................2
......................................................................................4
...........................................................................................12
................................................................. 12
Warning
Caution
Warning
Usage
Warning