MIDORI ULB-35 Series User manual

OPERATING MANUAL
ULB-35 SERIES
LED LIGHT SOURCE

Midori™ ULB-35
2
System Symbol Descriptions....................................................................... 3
Warning and Precautions............................................................................. 4
System Assembly and Operation ................................................................. 5
Air Flow Paths.............................................................................................. 6
Maintenance and Cleaning ........................................................................... 7
Troubleshooting Suggestions....................................................................... 7
Repair ......................................................................................................... 7
Manufacture Contact Information ................................................................ 8
Environment................................................................................................. 8
Electrical Ratings ......................................................................................... 8
Dimensions ................................................................................................. 9
Illumination System .................................................................................... 9
Product Ordering Information ..................................................................... 9
Approvals .................................................................................................. 10
Warranty ................................................................................................... 10
Agency Compliance Statements ................................................................ 11
FCC Class A Compliance Statement .......................................................... 11
Canadian Notice ........................................................................................ 11
Contents
Thank you for purchasing the Midori™ fiber optic illuminator which utilizes state-of-
the-art solid-state illumination technology. The light source is a high output, efficient,
compact and lightweight fiber optic light source for industrial applications where
space is a premium. The ULB-35 series fiber illuminators utilize eco-friendly solid
state LED lighting technology, exhibits instant-on and electronic intensity dimming
capability with long operating lifetime. The Midori™ ULB-35 LED fiber illuminator
is equipped with an ACMI fiber receptacle with separate Storz and Olympus style
screw-in adapters available to accommodate these other common fiber cable types.
The ULB-35 accepts 12V DC input voltage for portable battery operation as well.
Please read this operating manual in its entirety before using this product.
Preface

Operating Manual
3
Caution: Consult
accompanying
documentation
Caution: Hot Surface
Caution Hazard Warning
Lamp On Lamp Off
Light; Lighting;
Illumination Intensity Bright Light
Storage Humidity Transport Temperature
Alternating Current Direct Current
Manufacturer Do Not Immerse in Any
Liquid
Do not dispose of this product as unsorted municipal waste. Prepare
this product for reuse or separate collection as specified by Directive
2002/96/EC of the European Parliament and the Council of the
European Union on Waste Electronic and Electrical Equipment
(WEEE). If this product is contaminated, this directive does not apply.
+49°C
-20°C
System Symbol Descriptions

Midori™ ULB-35
4
WARNING / There are no user serviceable or replacement parts. Do not attempt to dismantle
MISE EN GARDE box or remove top cover. / Aucune pièce ne peut être réparée ou remplacée par
l’utilisateur. Ne pas essayer de démonter la boîte ou de retirer le couvercle du dessus.
WARNING / Only qualified personnel should make electrical inspections and repair of the LED
MISE EN GARDE Light Source. / Seul le personnel qualifié doit effectuer les vérifications électriques
et les réparations de cette source de lumière à DEL.
WARNING / The high intensity light at the front of the LED Light Source and at the tip of the
MISE EN GARDE fiber-optic bundle will create high temperatures and bright light. To minimize the
risk of injury, avoid direct viewing or contact. / La lampe à haute intensité, située
sur le devant de la source de lumière à DEL et sur le bout du faisceau de fibres
optiques, générera beaucoup de chaleur et une lumière vive. Afin de réduire les
risques de blessures, éviter de toucher l’appareil ou d’exposer directement l’œil à la
lumière de la lampe.
WARNING / To prevent temporary blinding and contact with heated parts, always plug the fiber
MISE EN GARDE optic bundle into the LED Light Source before turning the power on. / Pour éviter
tout aveuglement temporaire ou contact avec les pièces chauffées, toujours
brancher le faisceau de fibres optiques dans la source de lumière à DEL avant la
mise en marche.
WARNING / Do not use the LED Light Source directly in medical applications. / Ne pas utiliser
MISE EN GARDE une source de lumière à DEL directe à des fins médicales.
WARNING / Unit MAY BE HOT. Allow to cool before handling. / L’appareil PEUT ÊTRE CHAUD.
MISE EN GARDE Il est important de le laisser refroidir avant d’y toucher.
CAUTION / Preferred operation is in the horizontal position. Other operating orientations are
AVERTISSEMENT permitted. / L’appareil fonctionne de façon optimale à l’horizontale. Les autres
orientations sont permises.
CAUTION / Any changes or modifications made to this device that are not expressly approved
AVERTISSEMENT by manufacturer may void the user’s authority to operate the equipment. / Toute
modification apportée à cet appareil et non expressément approuvée par le fabricant
peut priver l’utilisateur de son droit d’usage.
CAUTION / PROVIDE ADEQUATE VENTILATION TO PREVENT OVER HEATING. Do not drape
AVERTISSEMENT this light source. Provide a 1.5 inch (3.8 cm) distance between LED Light Source
and any solid objects. / ASSURER UNE VENTILATION ADÉQUATE AFIN D’ÉVITER
LA SURCHAUFFE DE L’APPAREIL. Ne pas couvrir la source de lumière. Laisser au
moins 3,8 cm (1,5 po) de distance entre la source de lumière à DEL et tout objet.
CAUTION / DO NOT IMMERSE or store liquids above or on the LED Light Source. / NE PAS
AVERTISSEMENT IMMERGER la source de lumière à DEL dans des liquides ou placer des liquides
au-dessus de celle-ci.
CAUTION / Do not operate device without the cover in place. / Ne pas faire fonctionner
AVERTISSEMENT l’appareil sans son couvercle.
CAUTION / DO NOT obstruct the airway paths for sufficient cooling is required. / NE PAS obstruer
AVERTISSEMENT les voies d’aération afin de permettre le refroidissement adéquat de l’appareil.
CAUTION / Please read this entire manual prior to operation. / Lire le présent guide en entier
AVERTISSEMENT avant d’utiliser l’appareil.
CAUTION / Protection provided by the equipment maybe impaired if not used in accordance
AVERTISSEMENT with the manufacture recommendations. / La protection assurée par l’équipement
risque d’être altérée si l’appareil n’est pas utilisé conformément aux recommandations
du fabricant.
Warning and Precautions /
Mises en garde et précautions

Operating Manual 5
System Description and Operation
1. The light source power switch should be in the OFF position. Plug the
external 12vdc power supply into the 12vdc connector. Figure 1.
2. Plug the external power supply cord into AC receptacle main power.
3. Plug the fiber-optic bundle into the light port and connect the opposite
end to the equipment being used. Figure 2.
4. Turn the power switch to the ON position. LED indicator light will turn
on when light source is powered. Figure 3.
5. Adjust the intensity control to set the light intensity to the desired light
output level. Figure 3.
6. Turn unit OFF when not in use. Figure 3.
12vdc
Power Plug
Light Intensity
Knob
Light Port
ON/OFF Indicator
Figure 1. Back View
Figure 2. Fiber-Optic Bundle
Figure 3. Front View
Power ON/OFF
Rotate Knob

Midori™ ULB-356
Figure 4. Cooling and Air Flow Paths
1. Do not obstruct air flow paths. This device is designed to have proper
forced air cooling paths to maintain thermal stable operation.
2. Place in an area that provides adequate ventilation to prevent unit from
overheating. Do not drape the LED Light Source with cloth or objects
restricting airflow.
3. Airflow outlets are shown in below red arrow graphics.
4. 1/4-20 UNF mounting stud located in the middle of box bottom side.
Threaded
Mounting Stud:
1/4x20 UNF

Operating Manual
7
Maintenance and Cleaning
Repair
1. Turn OFF light source by rotating intensity control knob counterclock-
wise until the switch clicks off.
2. Completely disconnect power supply from both light source and mains
(power plug into ac outlet).
3. Wait for ~5 seconds until power supply discharges as observed on the
power supply LED indicator will turn off.
4. Reconnect power supply to both ac to main voltage and dc connector
to light source.
5. Turn ON light source by rotating knob clockwise until clicks on and
LED indicator light is on.
6. Rotate knob to increase light output intensity to desired output.
1. Turn the LED Light Source off and unplug the power cord from both
the wall outlet and the rear of the unit.
2. Wipe the external surfaces clean with a cloth dampened with mild
soap and water. DO NOT IMMERSE.
3. Wipe the power cords clean with a cloth dampened with mild soap and
water. DO NOT IMMERSE. DO NOT RECONNECT WET.
4. DO NOT plug the power source into a wall outlet until it is thoroughly dry.
5. It is recommended to periodically clean the reflective optical surface
near the LED. Please use a soft cotton Q-tip dipped in Isopropyl
Alcohol and wipe the reflective optic surfaces and allow to thoroughly
dry prior to use.
For repair information, please contact Customer Service at:
Telephone: [phone]
Email: [email protected]
In the event the unit stops functioning, try the following steps to operate light
source. The power supply exhibits internal protection circuitry for user safety pre-
cautions and will shutdown during certain instances. This equipment has been
tested to ESD conditions according IEC 61326-1 and performs to performance
criterion C. This means, that under certain conditions the overvoltage protection
of the power supply may turn the power supply output and the unit off to prevent
damage to the unit. In such case the power supply must be disconnected from
main power to reset this fault condition. In the event the unit suddenly turns off,
turn the unit off. Unplug the power supply from mains voltage (120V/ 230V). Wait
~5 seconds and plug the power supply back into mains voltage. Turn the unit on.
Troubleshooting Suggestions

Midori™ ULB-35
8
Manufacture Contact Information
Environment Ratings
Electrical Ratings
Supplier Name: Ushio America, Inc.
Address: 5440 Cerritos Ave.
Cypress, CA 90630
Telephone: [phone]
Email [email protected]
Website: www.ushio.com
Model or Type: ULB-35
Operating Temperature: 41° F to 104° F (5° C to 40° C)
Humidity: 0 to 95% rh (non-condensing)
Storage Temperature: -10° F to 140° F (-20° C to 60° C)
Humidity: 30 to 75% rh
Atmospheric Pressure: 700 hpa to 1060 hpa
Mode of Operation: Continuous
Safety System Classification: Class II
System Pollution Degree: 2
Installation Category: II
External Power Supply Ratings:
Input: 100 - 240 V~, 50/60 Hz, 1.4 A max
Output: +12 V , 5.0 A
Recommended PS: UAI Part: UPS-00
ULB-35 Power Ratings:
Voltage: +12V DC; 14V DC maximum
Current: 3.4 amp
Battery: Ushio America, Inc. recommends using a
UR (or other recognized testing laboratory)
recognized battery rated at 12V/9Ah or
equivalent with a minimum 3.5 amp
current limit rating.

Operating Manual
9
Dimensions
Illumination Source
Length: 127MM (5.0”)
Width: 90MM (3.5”)
Height: 68MM (2.7”)
Weight: 0.45 kg (1.0 lbs)
Product ID Description Order Code
ULB-35p 35W LED Light Source; OEM Black 1003883
UPS-00 Universal Input Power Supply 1003879
UPC-US US power cord; EN60320-C7 1003881
UPC-EU EU Power cord EN60320-C7 1003880
UPC-UK UK Power cord EN60320-C7 1003882
UPC-AU AU Power Cord; EN60320-C7 1004095
50159 Storz Fiber Adapter; screw-in 50159
50160 Olympus Fiber Adapter; screw-in 50160
LB-CLP 12vdc Car Power Plug Adapter LB-CLP
UAC-01 Portable Light Case 5002496
UPS-03 12vdc LiP Battery Pack 5002493
Product Ordering Information
[127 mm]
5.0”
[114 mm]
4.5”
[90 mm]
3.5”
[68 mm]
2.7”
Type: LED Custom Module
Color Temperature: 5700 K - 6500 K Nominal
Power: 35 Watts
Average LED Life*: 50,000+ Hours
* Based on LED manufacturer rated wattage and thermal operation.

Midori™ ULB-35
10
Approvals
The CE mark on this product indicates that it has been tested
to and conforms to the provisions noted within the following
directives:
Low Voltage: 2014/35/EU
EMC: 2014/30/EU
RoHS 2: 2011/65/EU
In accordance with the following standards:
EN61010-1
IEC 61326-1
EN 61326-1
IEC 62471
IEC/EN 61000 3-2
IEC/EN 61000 3-3
EN 50581
Conforms to UL Std 61010-1
Certified to CSA Std C22.2 No. 61010-1
WEEE
(www.lamprecycle.org)
4009043
Limited Warranty
USHIO America warrants the LED Light Source, when new, to be free of defects in
material and workmanship and to perform in accordance with the manufacturer’s
specifications when subject to normal use and service for a period of two years
from the date of purchase from USHIO America or an authorized agent. USHIO
America will either repair or replace any components found to be defective or at
variance from the manufacturer’s specifications within this time at no cost to the
customer. It shall be the purchaser’s responsibility to return the instrument to the
authorized distributor, agent, or service representative.
This limited warranty does not cover the breakage or failure due to tampering,
misuse, neglect, accidents, improper installation, modification, shipping, or to
improper maintenance, service, and cleaning procedures. This limited warranty
is also void if the instrument is not used in accordance with the manufacturer’s
recommendations or if required service is performed by anyone other than USHIO
America or an authorized agent. The purchase date determines limited warranty
requirements. No other express or implied limited warranty is given.

Operating Manual
11
Agency Compliance Statements
FCC Class A Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at
his own expense.
Canadian Notice
This equipment does not exceed the Class A limits for radio noise emissions as
described in the Radio Interference Regulations of the Canadian Department of
Communications.
Le present appareil numerique n’emet pas de bruits radioelectriques depassant
les limites applicables aux appareils numeriques de la classe A prescrites
dans le Reglement sur le brouillage radioelectrique edicte par le ministere des
Communications du Canada.
CAUTION Any changes or modifications made to this device
that are not expressly approved may void the user’s
authority to operate the equipment.
NOTE To maintain compliance with FCC Rules and
Regulations, cables connected to this device must
be shielded cables, in which the cable shield wire(s)
have been grounded (tied) to the connector shell.