Miele CS 1212 User manual

Installation Instructions
CS 1212 I, CS 1221 I en - CA
Installation, repair and maintenance work should be performed by
a Miele authorized service technician in accordance with national
and local safety regulations and the provided installation instructions.

Note to the installer:
Please leave this instruction book
with the consumer for the local
electrical inspector’s use.
The minimum distances given in
these Installation Instructions must
be observed in order to ensure safe
operation. Failure to do so increases
the risk of fire.
The cabinetry and venting hood
should be installed first to prevent
damage to the appliance.
~The countertop must be bonded
with heat resistant (212 °F/100 °C)
adhesive to prevent distortion or
dissolving.
Any back splashes must be
heat-resistant as well.
~The appliance must not be installed
over a dishwasher, washer, dryer,
refrigerator or freezer. Heat radiated by
the appliance may damage them.
~To eliminate the risk of burns or fire
by reaching over heated surfaces
cabinet storage space above the
appliance should be avoided. If cabinet
storage is necessary, the risk can be
reduced by installing a venting hood to
project horizontally a minimum of 5"
(127 mm) beyond the bottom of the
cabinets.
~This appliance has not been
designed for maritime use or for use in
mobile installations such as recreational
vehicles or aircraft. However, under
certain conditions it may be possible for
installation in these applications. Please
contact the Miele Technical Service
Department with specific requirements.
~You must ensure the power cord for
the appliance will not be subject to any
mechanical strain after installation.
~If a protective base is installed
beneath the appliance, a minimum
distance of 1 9/16" (40 mm) between the
top of the protective base and the
bottom of the appliance must be
maintained.
~The appliance must not be
permanently sealed into the countertop
when installed. The sealing strip under
the edge of the appliance provides a
sufficient seal for the countertop. See
"Sealing".
Keep this instruction book in a safe
place for reference and pass it on to
any future user.
SAFETY INSTRUCTIONS FOR INSTALLATION
30

Safety distances above the
appliance
The minimum safety distance given by
the hood manufacturer must be
maintained between the combiset and
the hood above it. See the installation
instructions of the hood for these safety
measurements.
If the hood manufacturers instructions
are not available or if flammable objects
are installed over the combiset (e.g.
cabinets, utensil rail, etc.), a minimum
safety distance of 30" (760 mm) must
be maintained.
If there is more than one appliance
beneath a hood (e.g. wok burner
and electric combiset), and they
have different minimum safety
distances always observe the
greater distance.
SAFETY INSTRUCTIONS FOR INSTALLATION
31

Safety distances to the sides
of the appliance
The appliance should only be installed
as shown in the illustrations, while
maintaining the required safety
distances shown. Do not install the
appliance between two tall cabinets,
this is a fire hazard.
A distance of at least 2" (50 mm) must
be kept between the countertop cut-out
and the rear wall because of the high
temperatures radiated.
The minimum distance abetween the
worktop cut-out and a wall or tall unit to
the right or left of it is:
2" (50 mm) for CS 1112
CS 1122
CS 1212
CS 1221
CS 1223
CS 1326
CS 1411
6" (150 mm) for CS 1312
CS 1322
CS 1421
10" (250 mm) for CS 1011
CS 1012
CS 1028
recommended
not recommended
not permitted
SAFETY INSTRUCTIONS FOR INSTALLATION
32
2 " (50 mm)
(50mm)
1
2"

Safety distance from the wall covering
If a wall covering is installed, a minimum safety distance must be maintained
between the countertop cut-out and the covering, since high temperatures can
damage these materials.
If the covering is made of a combustible material (such as wood), the distance
between the countertop cut-out and the wall covering must be a minimum of
2" (50 mm).
For coverings made of non-combustible materials (such as metal, marble,
granite, ceramic tiles) the minimum safety distance ebetween the countertop
cut-out and the wall covering must be 2" (50 mm) minus the thickness of the
covering.
For example: thickness of wall covering 9/16" (15 mm)
2" (50 mm) - 9/16" (15 mm) = minimum safety distance 1 3/8" (35 mm).
aWall frame
bWall covering
x= thickness of the wall covering
cCountertop
dCountertop cut-out
eMinimum safety distance
with flammable materials 2" (50 mm)
with non-flammable materials 2" (50 mm) minus x
Installation
33

Installation dimensions
CS 1212
aSpring clips
bAppliance front
cInstallation height
dPower supply cable (encased in flexible metal conduit),
L=783/4" (2000 mm)
eData plate
Installation
34

CS 1221
aSpring clips
bAppliance front
cInstallation height
dPower supply cable (encased in flexible metal conduit),
L=783/4" (2000 mm)
eData plate
Installation
35

Cut out
^Make the worktop cut-out for one or
more appliances as applicable.
Remember to maintain a minimum
safety distance from the back wall,
as well as from any tall unit or side
wall to the right or left of the
appliance(s).
See also "SAFETY INSTRUCTIONS
FOR INSTALLATION".
^Seal the cut surfaces with a suitable
sealant to avoid swelling caused by
moisture.
The materials used must be heat
resistant.
If during installation the seal around
the frame does not sit flush with the
countertop in the corners, the corner
radius, maximum 3/16" (4 mm), can
be carefully filed down to fit.
Installation
36

Installation of multiple
appliances
When installing more than one combiset appliance, a support bar bmust be
installed between the appliances.
Countertop cut-out
two appliances
For the installation of two appliances
the width of the countertop cut-out D is
the sum of A and C.
A,Band C= appliance widths
11 5/16", 15" or 22 11/16"
(288 mm, 380 mm or 576 mm)
minus 5/16"(8mm)to allow for the
overhang
D= width of the countertop cut-out
Countertop cut-out
three appliances
For the installation of three appliances
the width of the countertop cut-out D is
the sum of A and B and C.
If more than three appliances are
being installed, you will need to add,
A, B or C for each additional
appliance.
Installation
37

Sample calculations for a countertop cut-out for three appliances
A
appliance width
minus 5/16"(8mm)
B
appliance width
C
appliance width
minus 5/16"(8mm)
D
Countertop
cut-out
11"
(280 mm)
11 5/16"
(288 mm)
11"
(280 mm)
33 3/8"
(848 mm)
11"
(280 mm)
15"
(380 mm)
14 5/8"
(372 mm)
40 5/8"
(1032 mm)
11"
(280 mm)
22 11/16"
(576 mm)
22 3/8"
(568 mm)
56 1/16"
(1424 mm)
14 5/8"
(372 mm)
11 5/16"
(288 mm)
11"
(280 mm)
37"
(940 mm)
14 5/8"
(372 mm)
15"
(380 mm)
14 5/8"
(372 mm)
44 1/4"
(1124 mm)
14 5/8"
(372 mm)
22 11/16"
(576 mm)
22 3/8'
(568 mm)
59 11/16"
(1516 mm)
22 3/8"
(568 mm)
11 5/16"
(288 mm)
11"
(280 mm)
44 3/4"
(1136 mm)
22 3/8"
(568 mm)
15"
(380 mm)
14 5/8"
(372 mm)
52"
(1320 mm)
22 3/8"
(568 mm)
-22
3/8"
(568 mm)
44 3/4"
(1136 mm)
Installation
38

aSpring clips
bSupport bars
cSpace between support bar and countertop
dSealing strip
The illustration represents the attachment of spring clips aand support bars b
for 3 appliances.
An additional support bar is required for each additional appliance. The position
for attachment of an additional support bar depends on the width of appliance B.
Installation
39

Attaching the spring clips and
support bars
Wood or solid surface countertops
^Place the supplied spring clips a
and the support bars bat the
marked positions as shown above,
by laying them on the upper edge of
the cut-out and then securing them
with the 1/8" x 1" (3.5 x 25 mm) screws
(supplied).
Installation
40

Granite countertop
The screws are not needed for
granite countertops.
^Position and attach the spring clips
aand support bars bwith strong,
double-sided tape c.
^Coat the edges of the spring clips a,
^and the space ebetween the
support bars band the countertop
with silicone (supplied).
Installation
41

Installing the appliance /
appliances
^Feed the power cord down through
the cut-out.
^Place the front edge of the appliance
into the cut-out.
^With a hand on each side of the
appliance press down evenly on the
edges until it clicks into position.
When doing so make sure that the
appliance seal sits tightly on the
countertop to ensure it is sealed
correctly. This is important to ensure
an effective seal. Do not permanently
seal into the countertop.
When installing more than one
appliance, a sealing strip must be
inserted into the support bar.
^Push the installed appliance to the
side until the slots in the support bar
are visible.
^Insert the sealing strip dinto the
slots in the support bar b.
^Place the front edge of the next
appliance into the cut-out.
^Connect the appliance / appliances
to the main power supply (see
"Electrical connection").
^Turn the appliance / appliances on
and check the function.
The appliance may be lifted out
using a special tool.
The appliance can also be pushed
up and out from underneath.
Note: push the rear out first.
Installation
42

Sealing
The appliance must not be permanently
sealed into the countertop when
installed. The sealing strip under the
edge of the appliance provides a
sufficient seal for the countertop.
If the appliance is sealed into
position, the countertop or appliance
could be damaged if it needs to be
removed for maintenance or service.
Tiled surfaces
The grouting aand shaded area under
the appliance frame must be flat and
even, so that the frame will lie evenly
and the sealing strip under the edge of
the upper part of the appliance can
provide an adequate seal against the
countertop.
Installation
43

,CAUTION: Before installation or
servicing, disconnect the power
supply by either removing the fuse,
shutting off the main power supply
or manually "tripping" the circuit
breaker.
Installation work and repairs should
only be performed by a qualified
technician in accordance with all
applicable codes and standards.
Repairs and service by unqualified
persons could be dangerous and
the manufacturer will not be held
responsible.
Before connecting the appliance to
the power supply, make sure that
the voltage and frequency listed on
the data plate correspond with the
household electrical supply. This
data must correspond to prevent
appliance damage. Consult an
electrician if in doubt.
Only operate the combiset after it
has been installed into the
countertop.
Installer:
Please leave these instructions with
the consumer.
Power supply
^Be sure your electrical supply
matches the data plate.
The combiset is equipped with a
flexible metal conduit encasing 3 wires
ready for connection to a grounded
power supply.
A dedicated line and junction box
should be used to connect the
combiset to a 15 A circuit.
Black wire: connect to L1 (hot)
Red wire: connect to L2 (hot)
Green wire: connect to GND (ground)
240 V, 60 Hz, 15 A fuse rating.
Be sure the power outlet is accessible
after installation.
For further information, see the wiring
diagram provided with the appliance.
,WARNING:
THIS APPLIANCE MUST BE
GROUNDED!
Electrical connection
44

Disposal of packing materials
The cardboard box and packing
materials are biodegradable and
recyclable. Please recycle.
Ensure that any plastic wrappings,
bags, etc. are disposed of safely and
kept out of the reach of children.
Danger of suffocation!
Disposal of an old appliance
Old appliances contain materials that
can be recycled. Please contact your
local recycling authority about the
possibility of recycling these materials.
Before discarding an old appliance
disconnect it from the electrical supply
and cut off the power cord to prevent it
from becoming a hazard.
Help protect our environment
45

46

47

Alteration rights reserved / 4309
For the most updated manual see the Miele web site.
M.-Nr. 07 353 950 / 02