MikroTik RouterBOARD 411R User manual

RouterBOARD 411R
Quick Setup Guide and Warranty Information
First use
1. Connect antenna cable to the built in WiFI card's Main uFl connector
2. Connect a passive PoE powered ethernet cable to the device
Powering
The board accepts powering onl from the LAN1 Ethernet port:
●LAN1 Ethernet port J8 accepts 9..28V DC input (at the board; higher voltage needed to compensate for power loss on
long cables; at least 18V suggested) from non-standard (passive) Power over Ethernet injectors (no power over
datalines). The board does not work with IEEE802.3af compliant 48V power injectors. This device doesn't come fitted
with a power jack.
Booting process
This device doesn't come fitted with a Serial Port connector, so initial connection has to be done via the Ethernet cable, using
the MikroTik Winbox utilit . Winbox should be used to connect to the default IP address of 192.168.88.1 with the username
admin and no password.
In case IP connection is not available, Winbox can also be used to connect to the MAC address of the device. More
information here:
http:// iki.mikrotik.com/ iki/First_time_startup
In case ou wish to boot the device from network, for example to use MikroTik Netinstall, hold the S301 button of the device
when starting it until it beeps and the LED light turns off and RB411R will look for Netinstall servers.
Extension Slots and Ports
●One Ethernet port, supporting automatic cross/straight cable correction (Auto MDI/X), so ou can use either straight
or cross-over cables for connecting to other network devices. The Ethernet port accepts 9..28 V DC powering from a
passive PoE injector.
●Built-in 802.11b/g WiFi card (AR2417) with two uFl connectors to the left of it
Buttons and Jumpers
●ROS reset jumper hole (RESET, marked with a black circle in the diagram above, below S301) – resets RouterOS
software to defaults. Must short circuit the metallic sides of the hole (with a screwdriver, for example) and boot the
device. Hold screwdriver in place until RouterOS configuration is cleared.
●S301 – Holding this button during boot time will make RB411R look for Netinstall servers. Release the button after
the LED light goes out.
See www.routerboard.com for more information. Contact [e-mail] for support questions. rev. A (2-Jul-2009)

Operating S stem Support
Currentl tested operating s stem is MikroTik RouterOS (starting from version 3.25).
Cop right and Warrant Information
Cop right and Trademarks. Cop right MikroTikls SIA. This manual contains information protected b cop right law. No
part of it ma be reproduced or transmitted in an form without prior written permission from the cop right holder.
RouterBOARD, RouterOS, RouterBOOT and MikroTik are trademarks of MikroTikls SIA. All trademarks and registered
trademarks appearing in this manual are the propert of their respective holders.
Hardware. MikroTikls SIA warrants all RouterBOARD series equipment for the term of one ear from the shipping date to be
free of defects in materials and workmanship under normal use and service, except in case of damage caused b
mechanical, electrical or other accidental or intended damages caused b improper use or due to wind, rain, fire or other
acts of nature.
If ou have purchased our product from a MikroTik Reseller, please contact the Reseller compan regarding all warrant
and repair issues, the following instructions appl ONLY if ou purchased our equipment directl from MikroTik Latvia
To return failed unit or units to MikroTikls ou must perform the following RMA (Return Material Authorization) procedure.
Follow the instructions below to save time, efforts, avoid costs, and improve the speed of the RMA process. Take into
account that all goods have one ear warrant .
Instructions are located on our webpage here: http://rma.mikrotik.com
Manual. This manual is provided “as is” without a warrant of an kind, expressed or implied, including, but not limited to,
the implied warrant of merchantabilit and fitness for a particular purpose. The manufacturer has made ever effort to
ensure the accurac of the contents of this manual, however, it is possible that it ma contain technical inaccuracies,
t pographical or other errors. No liabilit is assumed for an inaccurac found in this publication, nor for direct or indirect,
incidental, consequential or other damages that ma result from such an inaccurac , including, but not limited to, loss of
data or profits. Please report an inaccuracies found to [e-mail]
See www.routerboard.com for more information. Contact [e-mail] for support questions. rev. A (2-Jul-2009)