Milestone pro MP-HDFB-4KT User manual

MP-HDFB-4K
4K Optical Fiber Extender
All Rights Reserved
Versi n: MP-HDFB-4K_2016V1.0
User Manual

4K Optical Fiber Extender
1
Preface
Read this user manual carefully before using this product. Pictures shown in this manual
is for reference only, different model and specifications are subject to real product.
This manual is only for operation instruction only, not for any maintenance usage.
Trademarks
Product model and its logo are trademarks. Any other trademarks mentioned in this
manual are acknowledged as the properties of the trademark owner. No part of this
publication may be copied or reproduced without our prior written consent.
FCC Statement
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. t has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a commercial
installation.
Operation of this equipment in a residential area is likely to cause interference, in which
case the user at their own expense will be required to take whatever measures may be
necessary to correct the interference.
Any changes or modifications not expressly approved by the manufacture would void
the user’s authority to operate the equipment.

4K Optical Fiber Extender
2
SAFETY PRECAUTIONS
To insure the best from the product, please read all instructions carefully before using the
device. Save this manual for further reference.
 Unpack the equipment carefully and save the original box and packing material for
possible future shipment
 Follow basic safety precautions to reduce the risk of fire, electrical shock and injury to
persons.
 Do not dismantle the housing or modify the module. t may result in electrical shock or
burn.
 Using supplies or parts not meeting the products’ specifications may cause damage,
deterioration or malfunction.
 Refer all servicing to qualified service personnel.
 To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this
product near water.
 Do not put any heavy items on the extension cable in case of extrusion.
 Do not remove the housing of the device as opening or removing housing may
expose you to dangerous voltage or other hazards.
 nstall the device in a place with fine ventilation to avoid damage caused by overheat.
 Keep the module away from liquids.
 Spillage into the housing may result in fire, electrical shock, or equipment damage. f
an object or liquid falls or spills on to the housing, unplug the module immediately.
 Do not twist or pull by force ends of the optical cable. t can cause malfunction.
 Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to
the device before cleaning.
 Unplug the power cord when left unused for a long period of time.
 nformation on disposal for scrapped devices: do not burn or mix with general
household waste, please treat them as normal electrical wastes.

4K Optical Fiber Extender
3
Intr ducti n
MP-HDFB-4K is a mini optical fiber extender for 4K resolution. t contains a transmitter
（MP-HDFB-4KT）and a receiver（MP-HDFB-4KR）. Compatible with multi-mode and
single-mode fiber, it extends graphic TMDS signals up to 400m/300m via single-mode
cable/ multi-mode cable. With its HDM 1.4& HDCP compliance design,
MP-HDFB-4Ksupports high definition (up to 4096x2160@30Hz, 1080p 3D) signal.
Package List
1×MP-HDFB-4K (MP-HDFB-4KT&MP-HDFB-4KR)
2× Power Adapter
1×Optical Fiber Cable (single-mode)
1×User Manual
N tes：Check whether all the items listed above are included in your package. f not,
contact your dealer to make up.
Appearances
MP-HDFB-4KT:
②PWRLED: lluminate when powered up
③LINKLED: lluminate when connecting
MP-HDFB-4KT &MP-HDFB-4KR
④USB: nsert a DC 5V 1A power adapter
here
⑤OUT: Connect with IN of MP-HDFB-4KR

4K Optical Fiber Extender
4
MP-HDFB-4KR:
C nnecti n:
The figure below illustrates a typical connection that can be utilized with MP-HDFB-4K:
Step1. nsert MP-HDFB-4KT into the HDM port of a HDM source device (e.g.a PC).
Step2. Connect OUT port of MP-HDFB-4KT to the IN port of theMP-HDFB-4KR with an
optical fiber cable.
Step3. nsert MP-HDFB-4KR into the HDM port of a HDM sink device (e.g. a monitor).
Step4. Plug DC 5V power adapters to the USB ports of both MP-HDFB-4KT and the
MP-HDFB-4KR.
N te: Connect MP-HDFB-4KT/ MP-HDFB-4KR with HDM source/ sink directly or
through a HDM cable.
②PWRLED: lluminate when powered up
③LINKLED: lluminate when connecting
MP-HDFB-4KT & MP-HDFB-4KR
④USB: nsert a DC 5V 1A power adapter
here
⑤IN: Connect with OUT of MP-HDFB-4KT

4K Optical Fiber Extender
5
Specificati n
M del
Spec MP-HDFB-4KT MP-HDFB-4KR
Input
nput Signal 1 HDM 1 Optical Fiber
nput Connector 19-pin Type A male HDM LC connector
Signal HDM 1.4 Optical Fiber
Output
Output 1 Optical Fiber 1 HDM
Output Connector LC connector 19-pin Type A male HDM
Signal Optical Fiber HDM 1.4
General
Resolution 4k (max)
Audio Format PCM, Dolby Digital, DTS, DTS-HD
HDM Standard Support HDM 1.4 and HDCP1.4
Transmission Distance ≤400m via single-mode fiber
≤300m via multi-mode fiber
Temperature 0 ~ 50℃
Reference Humidity 10% ~ 90%
Power Supply nput: AC 100~240V, 50/60Hz; Output: DC 5V 1A
Power Consumption ≤2.5w ≤2.3w
Dimension (W*H*D) 60*10*22 mm 60*10*22 mm
Weight 26g 26g

4K Optical Fiber Extender
6
Tr ublesh ting & Maintenance
Pr blems Causes S luti ns
Color losing or vague/
double image in HDM
display
Poor quality of the HDM
cable (if used) Change for qualified cable.
Power led isoff, operations
don’t work
Not been powered Power up the unit
Poor contact of USB port Make sure power adapter is
in well contact
No output on the display
Source/ Display is off Turn on the source/ display
Poor contact of HDM ports
Check the HDM ports one
by one to make sure they’re
in well contact.
f your problem persists after following the above troubleshooting steps, seek further help
from authorized dealer or our technical support.

4K Optical Fiber Extender
7
After-sales Service
f there appear some problems when running the device, please check and deal with the
problems referring to this user manual.
1) Pr duct Limited Warranty: We warrant that our products will be free from defects in
materials and workmanship for tw years, which starts from the first day the product
leaves warehouse (check the SN mark on the product).
Proof of purchase in the form of a bill of sale or receipted invoice must be presented
to obtain warranty service.
2) What the warranty d es n t c ver (servicing available f r a fee):
 Warranty expiration.
 Factory applied serial number has been altered or removed from the product.
 Damage, deterioration or malfunction caused by:
 Normal wear and tear
 Use of supplies or parts not meeting our specifications
 No certificate or invoice as the proof of warranty.
 The product model showed on the warranty card does not match with the
model of the product for repairing or had been altered.
 Damage caused by force majeure.
 Servicing not authorized
 Any other causes which does not relate to a product defect
 Delivery, installation or labor charges for installation or setup of the product
3) Technical Supp rt: Email to our after-sales department or make a call, please
inform us the following information about your cases.
 Product version and name.
 Detailed failure situations.
 The formation of the cases.
Remarks: For any questions or problems, please try to get help from your local
distributor.