Milestone pro MPTP-T70HDV User manual

MPTP-T70HDV
HDBaseT Transceiver Set
All Rights Reserved
Version: MPTP-T70HDV_2016V1.0
User Manual

HDBaseT Transceiver Set
Preface
Read this user manual carefully before using this product. Pictures shown in this manual
is for reference only, different model and specifications are subject to real product.
This manual is only for operation instruction only, not for any maintenance usage. The
functions described in this version are updated till August 2016. Any changes of
functions and parameters since then will be informed separately. Please refer to the
dealers for the latest details.
All product function is valid till 2016-8-22.
Trademarks
Product model and logo are trademarks. Any other trademarks mentioned in this manual
are acknowledged as the properties of the trademark owner. No part of this publication
may be copied or reproduced without the prior written consent.
FCC Statement
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. It has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a commercial
installation.
Operation of this equipment in a residential area is likely to cause interference, in which
case the user at their own expense will be required to take whatever measures may be
necessary to correct the interference.
Any changes or modifications not expressly approved by the manufacture would void
the user’s authority to operate the equipment.

HDBaseT Transceiver Set
SAFETY PRECAUTIONS
To insure the best from the product, please read all instructions carefully before using
the device. Save this manual for further reference.
Unpack the equipment carefully and save the original box and packing material for
possible future shipment
Follow basic safety precautions to reduce the risk of fire, electrical shock and injury
to persons.
Do not dismantle the housing or modify the module. It may result in electrical shock
or burn.
Using supplies or parts not meeting the products’ specifications may cause damage,
deterioration or malfunction.
Refer all servicing to qualified service personnel.
To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this
product near water.
Do not put any heavy items on the extension cable in case of extrusion.
Do not remove the housing of the device as opening or removing housing may
expose you to dangerous voltage or other hazards.
Install the device in a place with fine ventilation to avoid damage caused by
overheat.
Keep the module away from liquids.
Spillage into the housing may result in fire, electrical shock, or equipment damage. If
an object or liquid falls or spills on to the housing, unplug the module immediately.
Do not twist or pull by force ends of the optical cable. It can cause malfunction.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to
the device before cleaning.
Unplug the power cord when left unused for a long period of time.
Information on disposal for scrapped devices: do not burn or mix with general
household waste, please treat them as normal electrical wastes.

HDBaseT Transceiver Set
Table of Contents
1. Introduction.................................................................................................................1
1.1 Brief Introduction ...............................................................................................1
1.2 Features ............................................................................................................1
1.3 Package Contents .............................................................................................1
2. Panel Description........................................................................................................2
2.1 Transmitter (MPTP-T70HDVT) ..........................................................................2
2.2 Receiver (MPTP-T70HDVR)..............................................................................4
3. System Connection.....................................................................................................6
3.1 Usage Precautions............................................................................................6
3.2 System Diagram................................................................................................6
3.3 Connection Procedure.......................................................................................6
3.4 Twisted Pair Cable Connection..........................................................................7
4. Operations..................................................................................................................9
4.1 Operations of front panel buttons ......................................................................9
4.2 RS232 Control...................................................................................................9
4.2.1 Installation/uninstallation of RS232 Control Software..............................9
4.2.2 Basic Settings..........................................................................................9
4.2.3 RS232 Communication Commands ......................................................10
4.3 RS232 Passthrough Feature...........................................................................16
5. Specification..............................................................................................................18
6. Panel Drawing ..........................................................................................................20
7. Troubleshooting & Maintenance ...............................................................................21
8. After-sales Service....................................................................................................23

HDBaseT Transceiver Set
1
1. Introduction
1.1 Brief Introduction
MPTP-T70HDV is an HDBaseT Transceiver Set which contains a Transmitter and a
Receiver.
It uses HDBaseT technology to deliver HDMI/DVI/VGA signal, and the max transmission
is up to 70m. Moreover, bi-directional RS232 control, RS232 pass-through, IR control
and PoC are supported by this product.
MPTP-T70HDV has a good application in various occasions, such as computer realm,
monitoring, big screen displaying, meeting room, education and bank & securities
institution etc.
1.2 Features
HDMI/DVI/VGA output resolution up to 1920x1200@60HZ.
Support bi- directional PoC.
Maximum transmission distance is up to 70m for 1080p.
In-built scaler function, support scaling HDMI/ DVI/VGAsignals to match the native
resolution of the displays.
Provide external audio input for DVI video signal.
HDMI/DVI/VGA input signal can be switched automatically.
Supports firmware upgrading via USB.
Control methods: front panel buttons of transmitter, bi-directional RS232 control.
LED indicators show work status.
1.3 Package Contents
1 x Transmitter (MPTP-T70HDVT)
1 x Receiver (MPTP-T70HDVR)
4 x Mounting Ears
8 x Screws
2 x RS232 Cable
8 x Rubber Feet
1 x Power Adapter (DC24V 1.25A)
1 x User manual
Notes:If you find any defective or missing parts, please contact your local dealer.

HDBaseT Transceiver Set
2
2. Panel Description
2.1 Transmitter (MPTP-T70HDVT)
Figure 2-1 MPTP-T70HDVT
No.
Name
Description
①
Indicators
Power: Illuminates red when power on.
LINK: Twisted Pair Link status indicator, illuminates
green when successfully connected.
VGA: Illuminates green when there is VGAsignal input
DVI: Illuminates green when there is DVI signal input.
HDMI: Illuminates green when there is HDMI signal
input.
AUTO: Illuminates green under auto-switching mode.
②
FW
Micro USB port, used for firmware update.
Plug a flash disk or other storage device with update file
(MERGE.bin), and send command 50698% to update
firmware.
③
PoC switcher
ON: Enable bi-directional PoC function.
In this model, Transmitter and Receiver cannot be connected
with power adaptors at the same time. Only one power
adaptor needed.
OFF: Disable bi-directional PoC.
In this model, you can connect power adaptors to Transmitter
and Receiver at the same time, or only connect one power
HDMILINK DVIVGA FW SOURCE/AUTO
ON / OFF
PoCAUTO
RS232
Tx Rx
DC 24V
HDMI INPUTS AUDIO IR IN IR OUT
OUTPUT
PoC

HDBaseT Transceiver Set
3
adaptor to Receiver, Transmitter can be powered.
④
SOURCE/
AUTO
Press to select one source, press again to select next
source, switching circularly between HDMI, DVI and
VGAinput. The indicator of the selected input source will
illuminate green.
Long-press this button for 5 seconds or more to enter in
auto-switching mode and the indicator AUTO will lights
green. Under this mode, the last signal source
connected to transmitter will be recognized as input
signal. Press and hold for 5 seconds or more again to
exit auto-switching mode.
⑤
OUTPUT
Connect to the INPUT port of Receiver with a CAT5e cable.
⑥
HDMI INPUT
Connect with HDMI source device.
⑦
DVI INPUT
Connect with DVI source device.
⑧
AUDIO INPUT
Connect with the audio input socket of DVI or VGA source
device, provide external audio signal for DVI or VGA video
signal.
⑨
VGA INPUT
Connect with VGA source device.
⑩
IR IN
Connect with IR receiver to collect infrared signal, work with
far-end IR OUT port.
⑪
IR OUT
Connect with IR Emitter to send infrared signal, work with
far-end IR IN port.
⑫
RS232
Serial port, 3-pin pluggable terminal block, supports
bi-directional RS232 control and pass-through function,
connect with the control PC or other devices needed to be
controlled.
⑬
DC 24V
Connect with DC24V 1.25A power adaptor (not necessary if
Receiver connects with power adaptor and the PoC button is
switched on).

HDBaseT Transceiver Set
4
2.2 Receiver (MPTP-T70HDVR)
Figure 2-2 MPTP-T70HDVR
No.
Name
Description
①
Power
Illuminates red when power on.
②
LINK
Twisted Pair link status indicator, illuminates green when
successfully connected.
③
FW
Micro USB port, used for firmware update.
Firmware updated need auxiliary equipment, please contact with
our after-sales department for more details.
④
INPUT
Connect to the OUTPUT port of Transmitter with a CAT5e cable.
⑤
HDMI
OUTPUT
Connect with HDMI displayer.
⑥
DVI
OUTPUT
Connect with DVI displayer.
⑦
AUDIO
OUTPUT
Connect with audio player, synchronously output audio signal with
DVI or VGA video signal output.
⑧
VGA
OUTPUT
Connect with VGA displayer.
⑨
IR IN
Connect with IR receiver to collect infrared signal, work with
far-end IR OUT port.
⑩
IR OUT
Connect with IR Emitter to send infrared signal, work with far-end
IR IN port.
LINK FW
RS232
Tx Rx
DC 24V
HDMI AUDIO IR IN IR OUT
PoC
OUTPUTS
INPUT

HDBaseT Transceiver Set
5
⑪
RS232
Serial port, 3-pin pluggable terminal block, supports bi-directional
RS232 control and passthrough function, connect with the control
PC or other devices needed to be controlled.
⑫
DC 24V
Connect with DC24V 1.25A power adaptor (not necessary if
Transmitter connects with power adaptor and the PoC button is
switched on).
Note: Pictures shown on this manual are for reference only, different model and
specifications are subject to real product.

HDBaseT Transceiver Set
6
3. System Connection
3.1 Usage Precautions
1) System should be installed in a clean environment and has a prop temperature and
humidity.
2) All of the power switches, plugs, sockets and power cords should be insulated and
safety.
3) All devices should be connected before power on.
3.2 System Diagram
Figure 3-1 System Connection Diagram
3.3 Connection Procedure
Step1. Connect a HDMI source device (such as Blue-ray DVD) to HDMI INPUT port of
Transmitter with HDMI cable.
Step2. Connect a DVI source device (e.g. PC) to the DVI INPUT port of Transmitter VI
cable.
Step3. Connect a VGA source device (e.g. Laptop) to the VGA INPUT port of
Transmitter cable.
Step4. Connect a VGA source device (e.g. Laptop) or other audio source device to the
AUDIO INPUT port of Transmitter with audio cable.
Step5. Connect OUTPUT port of Transmitter and INPUT port of Receiver with single
CAT5e/CAT6 cable.
RS232
Tx Rx
DC 24 V
HDMI INPUTS AUDIO IR IN IR O UT
OUTPUT
PoC
RS232
Tx Rx
DC 24 V
HDMI AUDIO IR IN IR O UT
PoC
OUTPUTSINPUT
CAT5e/ 6A Cable
HDMI Cable
PC(with discrete graphics)
PC
HDMI Cable
Laptop
Standby
HDTV
HDTV
HDTV
Blu-ray DVD1
Transmiter
Receiver

HDBaseT Transceiver Set
7
Step6. Connect HDMI displayer (such as HDTV) to HDMI OUTPUT port of Receiver
with HDMI cable.
Step7. Connect DVI displayer to DVI OUTPUT port of Receiver with HDMI cable.
Step8. Connect VGA displayer to VGA OUTPUT port of Receiver with HDMI cable.
Step9. Connect audio device (such as AV amplifier) to the AUDIO OUTPUT port of
Receiver with audio cable.
Step10. When using the bi-directional IR control, do the following.
a) Connect an IR receiver to the IR IN port at either the Transmitter or the
Receiver.
b) Connect an IR Emitter to the IR OUT port at the other end.
Step11. MPTP-T70HDV supports bi-directional RS232 control. Connect control device
(e.g. PC) to RS232 port of Transmitter or Receiver, and then send commands to
control Transmitter or Receiver. Please refer to 4.2 R2323 control for more
details.
Step12. Connect a DC24V 1.25A power adaptor to the DC 24V port of the transmitter;
and make sure the switch “PoC “is turned on, the receiver will be energized
synchronously.

System Diagram shown in this manual are for reference only, more specific
schemes depend on real devices.
When the IR IN port receive the IR signal from IR remote, the IR signal can’t be
sent out via the IR OUT of the native unit.
When using PoC solution, the switch “PoC” must be turned on.
Connect HDBT ports via straight-thru CAT5e/6 cable with TIA/EIAT568B standard
terminations at both ends.
3.4 Twisted Pair Cable Connection
The twisted pair used in this extender MUST be a straight-through cable.
TIA/EIA T568A
TIA/EIA T568B
Pin
Cable color
Pin
Cable color
1
green white
1
orange white
2
green
2
orange
3
orange white
3
green white
4
blue
4
blue
5
blue white
5
blue white
6
orange
6
green
7
brown white
7
brown white

HDBaseT Transceiver Set
8
Notice: Cable
connectors MUST be
metal one, the
shielded layer of cable
MUST be connected to
the connector’s metal
shell, to make a better
transmission.
8
brown
8
brown
1st
Ground
4--5
1st
Ground
4--5
2nd
Ground
3--6
2nd
Ground
1--2
3rd
Group
1--2
3rd
Group
3--6
4th
Group
7--8
4th
Group
7--8

HDBaseT Transceiver Set
9
4. Operations
4.1 Operations of front panel buttons
Transmitter has a channel switching button SOURCE/ AUTO on the front panel, through
which users can switch input source signals.
It supports both manual and auto mode. (Default: Auto switching) Press and hold the
button SOURCE/AUTO for 5 seconds or send command “50770%”and “50771%”to
switch between the two modes.
Switching modes:
Manual switching mode
Long-press the button SOURCE/ AUTO for 5 seconds or more to enter manual
switching mode and the green indicator AUTO will extinguish. Press SOURCE/
AUTO to switch circularly between HDMI, DVI and VGA input signal source.
When the format of VGAinput signal is CVBS or YPbPr, the manual mode cannot
be switched to manual switching mode automatically.
Auto switching mode
Under manual switching mode, long-press the button SOURCE/ AUTO for 5
seconds or more to enter auto mode, Transmitter will automatically recognize the
signal source device that it was last connected to as input source.
4.2 RS232 Control
As RS232 can be transmitted bi-directionally between Transmitter and Receiver, so it is
able to control Receiver from local or control Transmitter from remote.
4.2.1 Installation/uninstallation of RS232 Control Software
Installation
Copy the control software file to the computer connected with Transmitter or
Receiver.
Uninstallation
Delete all the control software files in corresponding file path.
4.2.2 Basic Settings
First, connect Transmitter with all input devices and output devices needed, then to
connect it with a computer which is installed with RS232 control software. Double-click
the software icon to run this software.
Here we take the software CommWatch.exe as example. The icon is showed as below:

HDBaseT Transceiver Set
10
The interface of the control software is showed as below:
Please set the parameters of COM number, bound rate, data bit, stop bit and the parity
bit correctly, and then you are able to send command in Command Sending Area.
4.2.3 RS232 Communication Commands
Communication protocol: RS232 Communication Protocol
Baud rate: 9600 Data bit: 8 Stop bit: 1 Parity bit: none
Command
Function
Feedback Example
Transmitter (MPTP-T70HDVT)
Setup Commands
502xx%
Set the brightness to xx. XX ranges from
00 to 99
Brightness: xx
503xx%
Set the contrast to xx. XX ranges from 00
to 99
Contrast: xx
504xx%
Set the saturation to xx. XX ranges from
Saturation: xx
Parameter Configuration area
Monitoring area, indicates if the
command sent works.
Command Sending area

HDBaseT Transceiver Set
11
00 to 99
505xx%
Set the sharpness to xx. XX ranges from
00 to 99
Sharpness: xx
50606%
Auto-adjust the input parameter
VGA Input Auto
50607%
Adjust the color temperature
Color Temperature: xx
(xx can be medium,
warm, user, or cool)
50608%
Set the aspect ratio
Aspect Ratio: xx (xx
can be 16:9, 4:3, or
auto.)
50614%
Set the picture mode
Picture Mode: xx (xx
can be dynamic,
standard, mild, or user.)
50705%
Change the horizontal polarity to the
opposite
Hpolarity:0/1
50706%
Change the vertical polarity to the
opposite
Vpolarity:0/1
50701%
Switch to HDMI input
Switch to HDMI
50702%
Switch to DVI input
Switch to DVI
50704%
Switch to VGA/YPbPr/AV input
Switch to
VGA/YPbPr/AV
50710%
Set the VGA port to input VGA signal
Port VGA Set & Switch
to VGA!
50711%
Set the VGA port to input YPbPr signal
Port VGA Set & Switch
to YPbPr!
50712%
Set the VGA port to input AV signal
Port VGA Set & Switch
to AV!
50770%
Enable auto-switching
Auto Switching
50771%
Disable auto-switching
Manual Switching
50779%
Switch to RS232 mode 1, enable this unit
to control far-end devices
RS232 Mode 1: RS232
Control Scaler &
Remote
50780%
Switch to RS232 mode 2, enable far-end
devices to control this unit
RS232 Mode 2:RS232
& Remote Control

HDBaseT Transceiver Set
12
Scaler
50790%
Set the HDCP status of HDMI output
socket to Active
HDCP Active
50791%
Set the HDCP status of HDMI output
socket to On
HDCP On
50792%
Set the HDCP status of HDMI output
socket to Off
HDCP Off
50603%
Embed Audio into DVI signal
DVI Audio from
Embedded
50604%
Connect external audio to DVI signal
DVI Audio from LINE
50698%
Software update
50617%
Reset to factory default
Resolution Commands
50619%
Change the resolution to 1360X768 HD
Resolution: 1360x768
50626%
Change the resolution to 1024X768 XGA
Resolution: 1024x768
50627%
Change the resolution to 1280X720 720P
Resolution: 1280x720
50628%
Change the resolution to 1280X800
WXGA
Resolution: 1280x800
50629%
Change the resolution to 1920X1080
1080P
Resolution: 1920x1080
50620%
Change the resolution to1920X1200
WUXGA
Resolution: 1920x1200
50621%
Change the resolution to1600X1200
UXGA
Resolution: 1600x1200
Inquire Commands
50632%
Check the output resolution
Resolution: xx
50633%
Check the picture mode
Picture Mode: xx
50635%
Check the image aspect ratio
Aspect Ratio: xx
50636%
Check the brightness
Brightness: xx
50637%
Check the contrast
Contrast: xx
50638%
Check the saturation
Saturation: xx
50639%
Check sharpness
Sharpness: xx
50640%
Check the color temperature
Color Temperature: xx

HDBaseT Transceiver Set
13
50707%
Check the present resolution and polarity
1920x1080
Hpolarity:1
Vpolarity:0
50699%
Check the system version
Version Vx.x.x
50642%
Check the input signal format of VGA
Port VGA Set & VGA
Port VGA Set & YPbPr
Port VGA Set & CVBS
50631%
Check the input signal
Input:XXX
(XXX=YPbPr，VGA，
HDMI，DVI，AV)
50767%
Check the signal source switching mode
Auto Switching
Manual Switching
50641%
Check the RS232 mode
RS232 Mode 1: RS232
Control Scaler &
Remote
RS232 Mode 2:RS232
& Remote Control
Scaler
50605%
Check the audio source for DVI signal
DVI Audio from
Embedded
DVI Audio from LINE
Adjustment Commands
50678%
Enable screen output adjusting
Enter Output Position
Adjust
50679%
Disable screen output adjusting
Exit Output Position
Adjust
50670%
Move the image to left
Output Position Adjust
X xx
50671%
Move the image to right
Output Position Adjust
X xx
50672%
Move the image up
Output Position Adjust
Y xx
50673%
Move the image down
Output Position Adjust
Y xx

HDBaseT Transceiver Set
14
50674%
Pull left from right side (decrease image
width)
Output Width Adjust xx
50675%
Stretch right from right side (increase
image width)
Output Width Adjust xx
50676%
Stretch upwards from bottom side
(decrease image height)
Output Height Adjust xx
50677%
Stretch downwards from bottom side
(increase image height)
Output Height Adjust
xx
EDID Commands
50769%
Load EDID data from U-disk.
EDID read ok!
50772%
Restore EDID default.
EDID restore to default!
50773%
EDID pass-through.
EDID: bypass.
50774%
Customize EDID.
EDID: user.
50778%
Check EDID mode.
EDID: initial.
EDID: bypass.
EDID: user.
50799%
Program EDID file, send EDID data within
10s.
Waiting for edid within
10 secs!
Receiver (MPTP-T70HDVR)
80800%
Reset to factory default
80600%
Open analog audio output
Analog Audio Open
80601%
Close analog audio output
Analog Audio Close
80643%
Check the status for analog audio output
AUDIO MUTE
/UNMUTE
80605%
Check the signal format for VGA output
signal.
Output Format is RGB/
YPBPR
80606%
Change the resolution to 1920x1080i for
all displays.
Resolution:1920x1080i
80612%
Change the resolution to 1920x1080p for
all displays.
Resolution:1920x1080p
80613%
Change the resolution to 800x600p for all
displays.
Resolution:800x600p
80614%
Change the resolution to 1024x768p for
Resolution:1024x768p

HDBaseT Transceiver Set
15
all displays.
80615%
Change the resolution to 1280x1024p for
all displays.
Resolution:1280x1024p
80616%
Change the resolution to 1920x1200p for
all displays.
Resolution:1920x1200p
80627%
Change the resolution to 1280x720p for
all displays.
Resolution:1280x720p
80623%
Set the signal format as YPBPR for VGA
output signal
Switch To YPBPR
80622%
Set the signal format as VGA for VGA
output signal
Switch To VGA
80687%
Inquire current resolution(including
CVBS&YPBPR&RGB )
Resolution: xxxxxxxx
80700%
Enable far-end device to control this unit
RS232 Mode 1: RS232
Control Scaler &
Remote
80701%
Enable this unit to control far-end devices
RS232 Mode 2:RS232
& Remote Control
Scaler
80300%
Move the image up
Pricture Mvoe Up
80301%
Move the image down
Pricture Mvoe Down
80302%
Move the image to left
Pricture Mvoe Left
80303%
Move the image to right
Pricture Mvoe Right
80200%
Check the brightness
BRIGHTNESS is XX
80201%
Check the contrast
CONTRAST is XX
80202%
Check the saturation
SATURATION is XX
80203%
Check the chrominance
HUE is XX
80204%
Check the video format for output video
signal
Video output Is
YPBPR/RGB/CVBS
80207%
Check the resolution mode
Resolution is
Auto/Resolution is
Manual
80208%
Check the version
Versions X.X.XT
80214%
Check the RS232 mode
RS232 Mode 2:RS232
& Remote Control

HDBaseT Transceiver Set
16
Scaler
RS232 Mode 1: RS232
Control Scaler &
Remote
80212%
Auto mode for adjusting output resolution.
Switch Auto Mode
80213%
Manual mode for adjusting output
resolution.
Switch Manual Mode
11xxx%
Set the brightness value
Brightness:
12xxx%
Set the contrast value
Contrast:
13xxx%
Set the saturation value
Saturation:
14xxx%
Set the chromaticity value
Hue:
Note:
EDID and HDCP commands are for HDMI sources only.
50790%、50791%、50792% only used for Transmitter.
By default, Both Transmitter and Receiver are in RS232 Mode 1, the PC that is
connected to Transmitter can control Receiver by sending commands.
If you want to control Transmitter via the PC that is connected to Receiver, please
send 50780% and 80701% to make Transmitter and Receiver into RS232 Mode 2.
4.3 RS232 Passthrough Feature
Besides RS232 control function, MPTP-T70HDV supports bi-directional RS232
passthrough feature. Connect a control device to the RS232 port of Transmitter or
Receiver, and connect a device that need to be controlled to the remote RS232 port of
Transmitter or Receiver. The remote device can be controlled by sending commands via
control device.
For example, connect a PC to RS232 port of Transmitter, and then connect a projector
to RS232 port of Receiver, the connection diagram as shown as below. The remote
projector can be controlled by sending commands via PC. For specific commands,
please refer to the projector’s user manual.