Miller Century 5230 User manual

CENTURY®
L E G E N D A R Y L E A D E R S H I P
OWNER'S MANUAL
5130 / 5230
INSTALLATION, OPERATION, MAINTENANCE & PARTS
NOTE: MANUAL including SPECIFICATIONS, subject to change without notice
All ratings specified are based on structural factors only,
not vehicle capacities or capabilities.
CENTURY®
Miller Industries Towing Equipment Inc.
8503 Hilltop Drive
Ooltewah, Tennessee 37363 FORM NO. 0501140
08 / 01
Phone [phone] • FAX [phone] PRICE $25.00

LIMITED WARRANTY
MILLER INDUSTRIES TOWING EQUIPMENT INC., hereinafter referred to as MILLER, warrants to the
original purchaser that each new MILLER wrecker or other MILLER products will be free from defects in
material and workmanship for a period of twelve (12) months from date placed in service, but in no event
shall such warranty period exceed twenty-four (24) months from date of manufacture by MILLER. The
purchaser must promptly notify MILLER in writing of any failure in material or workmanship. In no event
shall MILLER accept such notification later than twenty-four (24) months from date of delivery or twelve
(12) months from date placed in service, whichever is earlier.
MILLER's obligation under this warranty, statutory or otherwise, is limited to the repair or replacement at
the MILLER factory, or at a point designated by MILLER, of such part or parts as shall appear upon
inspection by MILLER to be defective in material or workmanship. New or remanufactured parts will be
used for any replacement at MILLER's option. This warranty is not transferable. This warranty does not
obligate MILLER to bear the cost of labor or transportation charges in connection with the repair or
replacement of any parts found to be defective, nor shall it apply to a product upon which repairs or
alterations have been made unless authorized by MILLER.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, MILLER MAKES NO OTHER
WARRANTY, EXPRESS OR IMPLIED, AND HEREBY DISCLAIMS ALL OTHER WARRANTIES
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. MILLER shall in no event be liable for claimed downtime,
claimed loss of profits or goodwill, or any other special, incidental, indirect, or consequential damages
concerning or relating to any product or parts, whether based on negligence, strict liability, breach of
contract, breach of warranty, misrepresentation or any other legal theory, regardless of whether the loss
resulted from any general or particular requirement which MILLER knew or had reason to know about at
the time of sale.
MILLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, AS TO THE FINISHED PRODUCTS
MANUFACTURED OR SUPPLIED BY ANOTHER MANUFACTURER AND SUPPLIED BY MILLER TO
PURCHASER, including, but not limited to, any vehicle to which a MILLER product may be affixed or any
accessories or wire rope, and MILLER EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AS TO SUCH EQUIPMENT OR
PRODUCTS. This language shall in no way affect or diminish the rights of the purchaser to rely on such
warranties as are extended by such manufacturers or suppliers. MILLER shall, to the extent permitted
under applicable law, pass on to the purchaser such manufacturer's or seller's warranty.
MILLER, whose policy is one of continuous improvement, reserves the right to improve its products
through changes in design or materials as it may deem desirable without being obligated to incorporate
such changes in products previously sold. This warranty is not intended to cover or include the following
items, which are set forth by way of example and not limitation:
A. Normal deterioration of trim, paint, lettering, and appearance items due to wear or exposure to
weather, road conditions, road treatments, etc.
B. Any damage or defect due to accident, misuse, abuse, improper or unauthorized repairs, failure
to provide reasonable and necessary maintenance, or uses for which the equipment was not
designed or intended.
C. Alterations or modifications that affect performance, operation or reliability.
D. Normal maintenance parts including, but not limited to, wear pads, bushings, wire rope, mud
flaps, fenderettes, light bulbs, hydraulic oil, filters, and tow sling belts.
IT IS EXPRESSLY UNDERSTOOD THAT MILLER MAKES NO IMPLIED WARRANTY THAT MILLER
PRODUCTS SHALL BE FIT FOR THE PURPOSE OF LIFTING OR MOVING PEOPLE OR FOR ANY
OTHER IMPROPER USE.
SERIAL NUMBER
Miller Industries Towing Equipment Inc.
8503 Hilltop Drive
Ooltewah, Tennessee 37363
Telephone [phone]

Section VI - PARTS
This Section is provided by the manufacturer for the purpose of ordering
any component part of the CENTURY 5130 or 5230 that may be required
when part replacement is necessary. Be certain to use only original equipment
replacement parts for warranty purposes as well as for keeping your
CENTURY 5130 or 5230 in its original state and optimum operating
capacities. When ordering replacement or spare parts be sure to provide
the following information to the manufacturer’s Parts Department.
1. Manual Number & Date of Publication
2. Manual Page Number
3. Page Title
4. Reference Number of Part Desired
5. Part Number
6. Part Description
7. Quantity of Part Desired
Providing this information will help ensure that the correct parts will be
delivered to you in an expedient manner. Should additional information be
required for repair or replacement of certain components, contact your
Manufacturer Authorized Representative.
The Manufacturer reserves the right, without notice or obligation, to improve
or modify their products, which may change the specifications, models and
feature availability.
VI-1

VI-2
Section VI - PARTS (cont'd)
SUBFRAME ASSEMBLY

VI-3
REF. NO. PART
NO. REQ'D NUMBER DESCRIPTION
Section VI - PARTS (cont'd)
SUBFRAME ASSEMBLY
1 6 0300113 GREASE FITTING
2 2 0301861 QUICK PIN
3 2 0302538 BUSHING, 3-1/2" X 2-1/2" INTERNAL
4 8 0302540 CENTER BONDED MOUNT
5 12 0302541 SPECIAL WASHER
6 2 0303140 RAMP PAD
7 2 0303445 SAFETY CHAIN, SYSTEM 10
8 REF. 0306647 SPADE CYLINDER
9 REF. 0307012 LIFT CYLINDER
10 8 0400066 SCREW, 1/4"-20 X 3/4" HEX HD CAP
11 10 0400128 SCREW, 3/8"-16 X 1-1/4" FL HD SKT
12 4 0400139 SCREW, 3/8"-16 X 1-1/2" HEX SKT SET
13 10 0400181 SCREW, 1/2"-13 X 1-1/2" HEX HD CAP
14 2 0400219 SCREW, 1/2"-13 X 4-1/2" HEX HD CAP
15 2 0400260 SCREW, 5/8"-11 X 2" HEX HD CAP
16 4 0400276 SCREW, 5/8"-11 X 4-1/2" HEX HD CAP
17 4 0400281 SCREW, 3/4"-10 X 3-1/2" HEX HD CAP
18 12 0400288 SCREW, 3/4"-10 X 2-1/2" HEX HD CAP
19 4 0400294 SCREW, 3/4"-10 X 6-1/2" HEX HD CAP
20 23 0400392 NUT, 3/8"-16 NYLOK HEX
21 2 0400408 NUT, 1/2"-13 NYLOK HEX
22 2 0400421 NUT, 5/8"-11 NYLOK HEX
23 4 0400430 NUT, 3/4"-10 NYLOK HEX
24 12 0400431 NUT, 3/4"-10 NYLOK HEX
25 8 0400452 LOCKWASHER, 1/4" HELICAL
26 10 0400506 WASHER, 5/8" FLAT
27 4 0400508 LOCKWASHER, 5/8" HELICAL
28 8 0400510 WASHER, 3/4" FLAT (5230)
29 2 9046354 SPRING PIN, 1/4" X 2-1/2"
30 2 0705485 SPADE BLADE
31 2 0705500 SHAFT, LOWER SPADE
32 2 0707118 PIN, LIFT CYLINDER
33 2 0707394 SHAFT, UPPER SPADE
34 4 0714581 BOLTING PLATE
35 2 0715694 PIN, SPADE PIVOT
36 2 0715796 COVER PLATE, SPADE
37 1 0802211 FRONT BODY MTG TUBE (5130)
-- 1 0802868 FRONT BODY MTG TUBE WELDMENT (5230)
38 2 0802219 PIVOT PIN, LIFT CYLINDER
39 2 0804286 LOWER SPADE PAD WELDMENT
40 2 0804334 PIN, MULTI-POSITION
41 1 0804360 LEFT INNER SPADE WELDMENT
42 1 0804361 RIGHT INNER SPADE WELDMENT
43 2 0804405 BRACKET, BOOM PIVOT
44 1 0805899 SUBFRAME WELDMENT