Milwaukee AG 16-125 XC User manual

1
PAGE
4939 5228 01
Special Tools
Require
■ Forcing discs 4931 5990 18
■ TX 15 4931 5990 05
Important! ■ Before beginning the maintenance work, perform an initial check with a high voltage test according
to VDE (see chapter Electrical and Mechanical Test Instructions).
■ Before all repair work, pull the power plug from the socket!
Disassembly
Detaching
the handle
1
Unscrew the handle (1).
2
Machines with QUIK-LOK: Pull off the
Quick-Lock connection cable (2).
Removing the
carbon brushes
1 Loosen the screws (1) on both service
covers (2) with TX 15.
2
Carefully lever off the service cover (2)
with aid of a screwdriver.
3
Loosen the plug contact of the carbon
brushes (3) on both sides and remove the
carbon brushes (3).
Detaching the
guard cap
1
Fold away the hoop on the Fixtec nut (1)
and unscrew the Fixtec nut (1).
☞
In case of stiffness, a pin-type face
spanner can be used.
2
Remove the grinding disc (2).
3
Remove the clamping flange (3).
4
Loosen three screws (4) and remove the
spring washer (5).
5
Remove the guard cap (6).
1
2
1
1
3
2
1
2
3
2
1
6
4
2
3
5
3

2
PAGE
4939 5228 01
Removing the
complete spindle
assembly
1
Loosenfourscrews(1)onthebearingend
plate (2).
2
Remove the complete bearing end
plate (2).
Removing
the bearing
1
Pull off the bearing (2) from the front gear
box with aid of an interior extractor (1) in
direction of arrow.
Dismantling the
spindle assembly
1 Place the complete bearing end plate (2) -
(7) on a press. Apply pressure on the spin-
dle in direction of arrow. A gap will appear
betweenbevelgearwheel (2) and bearing
end plate (5). Insert the forcing discs
(service tool) into this gap and press off
thebevelgearwheel(2).Finally, pressout
the spindle assembly.
2
Dismantle the spindle assembly as fol-
lows:
– bevel gear wheel (2),
– O-ring (7),
– upper disc (6),
– bearing end plate (5),
– lower disc (4),
– spindle (3).
1
2
4
1
2
5
1
1
3
4
5
6
2
7
6

3
PAGE
4939 5228 01
Removing
the complete
armature
1
Loosen four screws (2).
2 Remove the gear box (6) with the com-
plete armature (4).
☞
If necessary, hit the gear box lightly
with a plastic hammer to remove it.
3
Steady the nut (3) with a fork wrench
(SW12) and grasp the armature (4) care-
fully with pliers (5). Loosen them contra-
rotating. (The armature can also be care-
fullyfixedinaviceprovidedwithprotective
jaws.)
4
Remove the nut (3).
Machineswith
seal ring:
Removing
the pinion
1
Remove the locking ring (7) and the fol-
lowing parts:
– disc (6),
– seal ring (5),
– press off the bearing (4),
– washer (3).
2
Remove the pinion (1) with the washer (2)
from the gear box.
3 Remove the washer (2) from the pin-
ion (1), if necessary, peel it off with aid of
a screwdriver.
Machineswith
sealing
washer:
Removing
the pinion
1
Remove the locking ring (7) and the fol-
lowing parts:
– disc (6),
– seal ring (5),
– press off the bearing (4),
– washer (3).
2
Remove the pinion (1) with the washer (2)
from the gear box.
1
5
4
23
6
7
7
6
2
1
5
34
8
7
6
5
4
3
12
8

4
PAGE
4939 5228 01
Machines
without
electronics:
Detaching the
armature
1
Remove the following parts from the ar-
mature (4):
– bearing sleeve (1),
– press off the bearing (2),
– insulating disc (3).
Machineswith
electronics:
Detaching the
armature
1
Remove the following parts from the ar-
mature (5):
– bearing sleeve (1),
– magnetic disc (2),
– press off the bearing (3),
– insulating disc (4).
Removing the
spindle lock
1
Press the press ram with a suitable man-
drel (steel pin) in direction of arrow onto
the middle of the push button (1).
2
Remove the push button (1), the pressure
spring (2) and the locking bolt (3).
☞
The push button is destroyed (1).
Removing the air
deflector ring
1
Remove the air deflector ring (1) with the
holding-down devices (2) from the motor
housing (3).
1
2
3
4
9
2
3
4
5
1
9
1
2
3
10
12
3
11

5
PAGE
4939 5228 01
Machines
without
electronics:
Removing
the field
1
Remove seven screws (5) and (A) from
the handle (B) and detach the handle.
2
Branch off the field wires (e, d, f, g) and re-
move the brush holders (4) and the con-
necting cables (3) and (8) from both sides.
3
Unscrew the strain relief (7).
4
Remove the switch (9) and branch off the
mains feed lines (6) (a, b).
Remove the mains connection cable (C).
5
Remove the field (1) from the motor hous-
ing (2).
☞
If necessary, hit the motor housing (2)
lightly with a plastic hammer for sup-
port.
Machineswith
electronics:
Removing
the field
Removing
the electronic
component
1 Remove seven screws (5) and (A) from
the handle (B) and detach the handle.
2
Branch off the field wires (e, d, f, g, k) and
remove the connecting cables (3) and the
brush holders (4) from both sides.
3
Unscrew the strain relief (7).
4
Branch off the switch (8) and remove it.
Branch off the mains feed lines (6) (a, b).
Remove the mains connection cable (9).
Machines with QUIK-LOK: Remove the
insert (E).
5
Machines with speed electronics:
Remove the electronic element (C).
6
Machines with constant electronics:
Remove the electronic element (D).
7
Remove the field (1) from the motor hous-
ing (2).
☞
If necessary, hit the motor housing (2)
lightly with a plastic hammer for sup-
port.
ed
a
b
i
ab
h
f
g
g
fd
e
1
2
3 8
3
4
6
5
A
7
9
4 B
C
12
k
f
d
d
f
k
b
a
ed
a
b
i
ab
h
f
g
e
g
kk
b
a
1
2
3
3
46
5
A
7
8
4 B
C
D
E
9
12

6
PAGE
4939 5228 01
Maintenance
General It is recommended to submit the machine to maintenance after the carbon brushes have switched off.
Cleaning Clean all parts – with the exception of the electrical parts – with cold cleaning agent. Caution! No
cleaning agent should penetrate into the bearing. Clean the electrical parts with a dry brush.
Check for wear Check the disassembled parts for wear (visual inspection) and replace worn parts.
Electrical tests Before reassembling, perform an electrical test on all relevant parts (see chapter Electrical and
Mechanical Test Instructions).
Lubrication Each time maintenance is performed, the machine is to be lubricates as stated in the lubrication plan.
After the machine is fully disassembled, completely remove the old grease and replace with new
grease. The grease must be applied to the machine as indicated in the lubrication plan.
Legend
■Use a total of 12 g grease Centoplex O Est (4931 621 977 - 100 g Tube).
ACover with 2 g grease Centoplex O Est.
BFill with 10 g grease Centoplex O Est.
Torques Screws in plastic 1.8 Nm
Screws in metal 2.5 Nm
Nut 6.0 Nm
AA
A
BB
10 g 10 g

7
PAGE
4939 5228 01
Assembly
Mounting the
bearing sleeve 1Insert the bearing sleeve (2) into the hous- ing (1) as far as it will go.
☞Do not pre-assemble the bearing
sleeve (2) on the armature. When
mounting the armature in the motor
housing (1), the bearing sleeve (2) is
pushed into the magnetic disc of the
armature. This might result in malfunc-
tion of the machine!
Machineswith
electronics:
Mounting
the field
Mounting
the electronic
element
1Insert the field (1) into the motor hous-
ing (2).
2Machines with constant electronics:
Connect the electronic element (D) to the
field (1) (e, d, f, g, k) and insert it.
3Machines with speed electronics:
Connect the electronic element (C) to the
field (1) (e, d, f, g, k) and insert it.
4Machines with QUIK-LOK: Mount the in-
sert (E) (to connect the Quick-Lock cable).
5Insert the mains connection cable (9).
Connect the mains feed lines (a, b) (6) to
the switch (8). Insert the switch (8).
6Screw down the strain relief (7).
7Connect the connecting cables (3) to the
carbon brush holders (4) and insert them
on both sides.
8Put together the handle halves (B)
and fasten them with seven screws (A)
and (5).
☞Take care that all electronic parts are
inserted properly into the handle (B)
and that no part is squeezed or
jammed!
1
2
1
ed
a
b
i
ab
h
f
g
e
g
kk
b
a
k
f
d
d
f
k
b
a
1
2
3
3
46
5
A
7
8
4 B
C
D
E
9
2

8
PAGE
4939 5228 01
Machines
without
electronics:
Mounting
the field
1Insert the field (1) into the motor hous-
ing (2). Press it in, if necessary.
2Insert the mains connection cable (C) and
connect the mains feed lines (a, b) (6) to
the switch (9).
3Screw down the strain relief (7).
4Connectthe connecting cables(3) and(8)
(e, d, f, g) to the field (1). Connect the con-
necting cables (3) to the carbon brush
holders on both sides (4) and insert them
on both sides.
5Put together the handle halves (B)
and fasten them with seven screws (A)
and (5).
Mounting the air
deflector ring 1Insert both holding-down devices (2) into the motor housing (3).
2Put on the air deflector ring (1).
Mounting the
spindle lock 1Mounta newpushbutton(1), thepressure spring (2) and the locking bolt (3) and in-
sert them into the front gear box.
ed
a
b
i
ab
h
f
g
g
fd
e
1
2
3 8
3
4
6
5
A
7
9
4 B
C
2
1 2
3
3
1
2
3
4

9
PAGE
4939 5228 01
Machines
without
electronics:
Mounting the
armature
1Mount the following parts on the arma-
ture (1):
– insulating disc (2),
– press on the bearing (3).
Machineswith
electronics:
Mounting the
armature
1Mount the following parts on the arma-
ture (1):
– insulating disc (2),
– press on the bearing (3),
– magnetic disc (4).
Machineswith
sealing
washer:
Mounting
the pinion
1Mount the following parts in the front gear
box:
– washer (3),
– press in the bearing (4),
– seal ring (5),
– disc (6),
– locking ring (7).
2Insert the washer (2), the pinion (1) and
the nut (8) into the gear box in preparation
for mounting the armature.
Machineswith
seal ring:
Mounting
the pinion
1Mount the following parts in the front gear
box:
– washer (3),
– press in the bearing (4),
– seal ring (5),
– disc (6),
– locking ring (7).
2Mount the washer (2) on the pinion (1).
3Insert the assembled pinion (1) and the
nut (8) into the gear box in preparation for
mounting the armature.
3
2
1
5
3
2
1
4
5
7
6
5
4
3
12
8
6
7
6
2
1
5
34
8
6

10
PAGE
4939 5228 01
Inserting
the complete
armature
1Insert the completely assembled arma-
ture (4) into the front gear box, rotating it.
Carefully hold the armature with pliers for
support. (The armature can also be care-
fullyfixedinaviceprovidedwithprotective
jaws.)
☞Machines without electronics: Mag-
netic disc (A) does not exist.
2Machines with sealing washer: Put the
washer (9) on the end of the shaft.
3Put the pinion (8) and the nut (3) on the
end of the armature shaft (4).
Useaforkwrench(SW12)andpliers (5)to
screw in the armature, contra-rotating.
4Use four screws (2) to fasten the front
gear box to the motor housing (7).
Assembling
the spindle 1Mount the following parts on the spindle shaft (6):
– disc (5),
– bearing end plate (4),
– disc (3),
– O-ring (2),
– press on the bevel gear wheel (1) flush
in direction of arrow.
Mounting
the bearing 1Press the bearing (1) into the front gear box as far as it will go.
1
5
4
23
6
7
89
A
7
6
5
4
2
1
3
8
1
9