Minebea Intec Puro YP-DP1 User manual

Puro® Thermal Direct Printer YP-DP1
Operating manual
98627-000-25 Edition 1.0.0 02/17/2020
Minebea Intec Bovenden GmbH & Co. KG, Leinetal 2, 37120 Bovenden, Germany
Phone: [phone] Fax: [phone]

Foreword
Must be followed!
Any information in this document is subject to change without notice and does not represent a commitment on
the part of Minebea Intec unless legally prescribed. This product should only be operated/installed by trained
and qualied personnel. In correspondence concerning this product, the type, name, and release number/serial
number as well as all license numbers relating to the product have to be cited.
Note
This document is partially protected by copyright. It may not be changed or copied, and it may not be used
without purchasing or written permission from the copyright owner (Minebea Intec). The use of this product
constitutes acceptance by you of the abovementioned provisions.

Table of contents
1 Introduction.........................................................................................................................................2
1.1 Read the manual.........................................................................................................................................................2
1.2 This is what operating instructions look like..........................................................................................................2
1.3 This is what lists look like...........................................................................................................................................2
1.4 This is what menu items and softkeys look like.....................................................................................................2
1.5 This is what the safety instructions look like.......................................................................................................... 2
2 Safety instructions...............................................................................................................................4
2.1 General safety information.......................................................................................................................................4
2.2 Incoming goods inspection.......................................................................................................................................4
2.3 Before operational startup........................................................................................................................................4
3 Setup instructions................................................................................................................................5
3.1 Printer overview..........................................................................................................................................................5
3.2 Operation specication .............................................................................................................................................5
3.3 Self test.........................................................................................................................................................................5
4 Dimensions .......................................................................................................................................... 7
4.1 Paper Size ....................................................................................................................................................................7
5 Installation...........................................................................................................................................8
6 Connection...........................................................................................................................................9
6.1 Power supply...............................................................................................................................................................9
6.2 Data interface..............................................................................................................................................................9
7 Specications .................................................................................................................................... 10
7.1 Equipment supplied................................................................................................................................................. 10
7.2 Technical data ...........................................................................................................................................................10
8 Replacing paper roll............................................................................................................................ 11
9 Disposal ..............................................................................................................................................12
Puro® Thermal Direct Printer YP-DP1 Table of contents
Minebea Intec EN-1

1 Introduction
1.1 Read the manual
-Please read this manual carefully and completely before using the product.
-This manual is part of the product. Keep it in a safe and easily accessible location.
1.2 This is what operating instructions look like
1. - n. are placed before steps that must be done in sequence.
1.3 This is what lists look like
-indicates an item in a list.
1.4 This is what menu items and softkeys look like
[ ] frame menu items and softkeys.
Example:
[Start]- [Applications]- [Excel]
1.5 This is what the safety instructions look like
Signal words indicate the severity of the danger involved when measures for preventing
hazards are not followed.
DANGER
Warning of personal injury
DANGER indicates death or severe, irreversible personal injury which will occur if the
corresponding safety measures are not observed.
Take the corresponding safety precautions.
WARNING
Warning of hazardous area and/or personal injury
WARNING indicates that death or severe, irreversible injury may occur if appropriate
safety measures are not observed.
Take the corresponding safety precautions.
CAUTION
Warning of personal injury.
CAUTION indicates that minor, reversible injury may occur if appropriate safety
measures are not observed.
Take the corresponding safety precautions.
is placed before a step.
describes the result of a step.
Puro® Thermal Direct Printer YP-DP1 1 Introduction
EN-2 Minebea Intec

NOTICE
Warning of damage to property and/or the environment.
NOTICE indicates that damage to property and/or the environment may occur if
appropriate safety measures are not observed.
Take the corresponding safety precautions.
Note:
User tips, useful information, and notes.
1 Introduction Puro® Thermal Direct Printer YP-DP1
Minebea Intec EN-3

2 Safety instructions
2.1 General safety information
-The equipment may only be used as intended for printing tasks.
-Observe the operating limits of the device.
-Position the device so that the power plug is freely accessible and the power cord
does not present an obstacle or trip hazard.
-Unplug the power cord from the mains supply before cleaning.
-Make sure that no liquid enters the equipment.
2.2 Incoming goods inspection
The shipment must be checked for completeness. A visual inspection must be performed
to determine if the shipment has been damaged. If there are grounds for a complaint, this
must be brought to the attention of the delivery company immediately. A Minebea Intec
sales or service point must be informed.
The shipment must be checked for completeness. A visual inspection must be performed
to determine if the shipment has been damaged. If there are grounds for a complaint, this
must be brought to the attention of the delivery company immediately. A Minebea Intec
sales or service point must be informed. Visit our website http://www.puroscales.com or
contact your dealer.
2.3 Before operational startup
NOTICE
Perform visual inspection.
Before operational startup as well as after storage or transport, inspect the product
visually for signs of mechanical damage.
The product may not be put into operation if it has visible damage and/or is
defective.
Puro® Thermal Direct Printer YP-DP1 2 Safety instructions
EN-4 Minebea Intec

3 Setup instructions
3.1 Printer overview
1 Paper case cover
2 Panel
3 SEL button
4 LF button
5 Paper case
6 Printer head
7 Indicator light
8 Reserve case
9 Interface connector RS232
10 Power connector
11 ON/OFF Switch
3.2 Operation specication
After turning on the printer, the indicator light is on, shows that the printer is online, and
it is ready to receive data.
The light is o, shows that the printer is oine, and it can not receive data.
When the light ash to show the paper is lacking, and the printer can not receive data.
The SEL button can switch online or oine status.
When the printer is oine, press the LF button, and the printer will feed paper.
3.3 Self test
Turn on the printer, press the SEL button to make printer oine (when use new dot
matrix printing and thermal printing model, no need to
3 Setup instructions Puro® Thermal Direct Printer YP-DP1
Minebea Intec EN-5

refer this step), press the LF button, and don’t release, then press the SEL button, and
then release the both two buttons at the same time, and then the printer will print out the
self-check scrip.
Puro® Thermal Direct Printer YP-DP1 3 Setup instructions
EN-6 Minebea Intec

4 Dimensions
4.1 Paper Size
Paper Type Thickness Width Diameter
Thermal Paper 0.06-0.08 mm 57±0.5 mm max. 50 mm
4 Dimensions Puro® Thermal Direct Printer YP-DP1
Minebea Intec EN-7

5 Installation
1. Drill two mounting holes in the desired position at a distance of 93.5 mm.
2. Fix two screws on the equipment.
3. Hang the printer on the equipment.
Puro® Thermal Direct Printer YP-DP1 5 Installation
EN-8 Minebea Intec

6 Connection
6.1 Power supply
WARNING
Warning of hazardous area and/or personal injury
Incorrect supply voltage.
It is essential that the power supply provided is used under all circumstances.
Power connector (1)
6.2 Data interface
Interface connector (2)
Use the supplied connecting cable YP-CAS1.
6 Connection Puro® Thermal Direct Printer YP-DP1
Minebea Intec EN-9

7 Specications
7.1 Equipment supplied
No. Position
1 YP-DP1 Printer
2 Safety Instructions with QR-code with access to detailed documentation
3 Connecting cable YP-CAS1
4 Power supply unit
7.2 Technical data
Item Specication
Printing method Direct thermal line printing
Paper width 57 mm
Resolution ration 8 dots/mm (384 dots/line)
Character per line 64/32/24
Printing speed 50 mm/sec (when the utilisation rate is 25%
Character size 6x8 dots, 8x16 dots, or 12x24 dots
Chinese character library GB2312, 16x16 dots, or 24x24 dots
Paper supplied 57 mm wide, 50 mm Ø
Interface RS232
Input power
Operating temperature (°C) 5...50
Storage temperature (°C) -20...60
Operating humidity (%) 10...80
Storage humidity (%) 10...90
Puro® Thermal Direct Printer YP-DP1 7 Specications
EN-10 Minebea Intec

8 Replacing paper roll
CAUTION
Warning of personal injury.
Print head may be hot!
Allow the print head to cool down before replacing the paper roll.
Notice the direction of the paper when using thermal series, according to Fig.1.
1. Open the paper cover.
2. Insert the axis through the paper roll and place the axis with the paper roll in the slot
into the printer. Pull out a small amount of paper and insert the paper into the feeder,
according to Fig. 2.
3. Power the printer on, press SEL button, make SEL indicator light o, then press LF
button, make the print head to run, and the paper will come out, according to Fig. 3.
4. Press SEL button again or turn o the power.
5. Close the paper cover, according to Fig. 4.
8 Replacing paper roll Puro® Thermal Direct Printer YP-DP1
Minebea Intec EN-11

9 Disposal
If the packaging is no longer required, please take it to your local waste disposal facility
and/or a reputable disposal company or collection point. The packaging largely consists
of environmentally friendly materials which can be used as secondary raw materials.
It is not permitted—even for small businesses—to dispose of this product with the regular
household waste or at collection points run by local public waste disposal companies.
EU legislation requires its Member States to collect electrical and electronic equipment
and dispose of it separately from other unsorted municipal waste so that it can then be
recycled.
Before disposing of or scrapping the product, any batteries should be removed and taken
to a suitable collection point.
Please see our T&Cs for further information.
We reserve the right not to accept products that are contaminated with hazardous
substances (ABC contamination) for repair.
Puro® Thermal Direct Printer YP-DP1 9 Disposal
EN-12 Minebea Intec

Published by
Minebea Intec Bovenden GmbH & Co. KG | Leinetal 2 | 37120 Bovenden, Germany
Phone: [phone] | Email: [email protected]
www.minebea-intec.com