miniBatt MB-PWDRIVE User manual


WirelessFastChargerManual

●ThisproductiscompatiblewithWirelesschargingprotocolofQi（V1.0、V1.1&V1.2）WPC.
●Suitableforallsmartphoneswithwirelesschargingfunction.
●Content:
1.Usermanual
2.Wirelesscharger
3.MicroUSBcable

●Productdescription:


1. Front;2.back;3.left;4.right;5.top;6.bottom;




●Usesteps:
1. Therearetwotypeholdercanbeselectedbaseonyouloving:
holder1,fixedchargertoinstrumentpanelforcar,seetheabovefigure:holder1
holder2,fixedchargertoair‐conditionerportforcar,seetheabovefigure:holder2

2. WhenyouconnecttheMicroUSBcablebetweenthechargerandapoweradapterandsupply
ACpowerintothepoweradapter,theoperationasbelow,theredLEDlightwillturnon.



2.Putthephoneonthewirelesscharger,baseonbelowfigureinsertthephoneintothecharger
padandfixedthephonewell.ThenwillchargethephoneandblueLEDlightison.
Carchargerholder
forinstrumentpanel
Carchargerholder
forAir‐conditioner
Holder1
Holder2

3.IfyouremoveyourdevicefromthechargertheredLEDturnsonagain.

●Lightstatus:
1.Redled:poweron,nocharging
2.Bluelight:charging
3.Redlightflashing:chargingfullforsmartphonewithSamsung.
4.Bluelightflashing:voltage/current/temperatureanomalies.

●Notes:
1.Thisproductmustbeusedasrequired;otherwiseitcancauseafire,explosionorother
dangerrisk.
2.CheckthattheUSBcableissuitableforcharging.Thedevicechargingcurrentislargeand
requiresa1.6‐2.0AUSBcable,otherwisethechargermaynotchargeornegativephenomena
suchasfrequentrestartcanbecaused.
3.Toensurethatnodebrisareonthechargingplatform,sensitiveequipmentandother
non‐metalsorelectromagneticQIarticlesshouldnotbeplacedonthechargingplatform.
4.Ensurethatthedevicemeetsthecoillocation.Ifitdoesn’tfitthechargermaynotchargeor
negativephenomenasuchasfrequentrestartcanbecaused.
5.Ensurethechargingplatformandthedevicearenotoverheating.Ifthechargerorthedevice
reachanunusuallevel‐pleasecutoffthepowersupplyandcontactthemanufacturer.
6.Keepthedevicedry,donotstoreorusethechargerinveryhotorverycoldenvironments.
7.Donotattempttoopen,throw,hitorshakethecharger.
8.Medicaldevicemanufacturersrecommendeddistancebetweenawirelessdeviceandan
implantedmedicaldeviceatleast20cm!Toavoidpotentialinterferencewiththemedical
device,ifthereisanyreasontosuspectthatinterferenceoccurs,pleasecutoffthepower
immediatelyandcontactthemanufacturerandyourdoctor.

●Specification：
Standard:QistandardcompliantV1.0/V1.1/V1.2
Numberofcoils:two
Chargingdistance:≤8mm
Input:microUSB9V/1.8AQC2orQC3forcar
Wirelessoutputself‐adaption
Output(NormalMode):5Wmax.
Output(FastChargeModel):10Wmax,ONLYforSamsungGalaxyS7,S7Edge,Note5andS6
Edge+.QC2.0AdaptiveFastChargerisrequiredforthefastchargewirelesschargingfeature.

Chargingefficiency:≤78%
Operatingtemperature:0°C‐50°C
Humidityrange:45‐85%RH


FCCStatement:
ThisdevicecomplieswithPart15oftheFCCrules.Operationissubjectedtothefollowingtwoconditions:
(1)thisdevicemaynotcauseharmfulinterference,and(2)thisdevicemustacceptanyinterferencereceived, 
includinginterferencethatmaycauseundesiredoperation.Changesormodificationsnotexpresslyapprovedby
thepartyresponsibleforcompliancecouldvoidyourauthoritytooperatetheequipment.



