MINIMOTO XRF 500 User manual

Important: You must
charge your MINIMOTO™
Motocross Bike a minimum
of 12 hours before you
can use it.
RECHARGE the battery
EACH TIME you use it.
TO PROTECT THE LIFE
OF THE BATTERY,
recharge the battery
at least once a month.
FOLLOW ALL SAFETY
RULES AND SET UP
INSTRUCTIONS IN THIS
MANUAL THOROUGHLY.
FAILURE TO DO SO
MAY VOID YOUR
WARRANTY.
DO NOT RETURN THE
MINIMOTO™
Motocross Bike
TO THE STORE! IF YOU ARE
MISSING PARTS OR
NEED ASSISTANCE,
PLEASE CONTACT US
TOLL- FREE:
1-800-434-6178
8 AM TO 7 PM CST,
Mondaythrough Friday,
(excluding holidays)
OR contactus by:
email at:
customerser[email protected]
SKU#15573
#15573
Toy Quest
Los Angeles, CA 90064.All Rights Reserved. Made in China.
www.toyquest.com
Conforms to ASTM F963. Colors and content may vary.
15573 1.0(03/22)
15573 1.2(04/09)
15573 1.3(04/28)
15573 1.4(05/07)

Please read this manual and save it with your original sales receipt.
Tools needed for assembly (included): Three Allen Keys, One Wrench, and one Detachable Screwdriver.
Use only with included: One 36 Volt Lead-Acid Rechargeable Battery,
three Ignition Keys and one Battery Charger.
(Protective equipment not included)
SKU#15573
INSTRUCTION
MANUAL
IMPORTANT!
Read completely before
attempting to ride
5
*On level surfaces
with normal loads.

MINIMOTO
™
MOTOCROSS BIKE
1
Contents Page
MINIMOTO MOTOCROSS BIKE
Owner’s manual and safety information
2
Warnings
3 - 4
Electrical hazard
5
Vehicle set up and assembly
6-7
Brake adjustment
8
Battery charging information
9
Steps to charge battery
10
Battery care
11
Riding rules
15
Battery disposal
14
How to replace the battery
12 - 13
Pre-ride checklist
16
How to ride your MINIMOTO™ MOTOCROSS BIKE
17
Special safety warnings
18
Tire inflation procedure
19
Tire repair
20
Circuit breaker/If you lose the keys
21
Replacing the chain if it "pops off"
22
Chain adjustment
25
Replacing brake and wheel
23 - 24
Trouble shooting
26 - 27
Limited warranty and registration policy
28
Registration card / VIN number
29
Appendix — spare part list
30 - 31

MINIMOTO
™
MOTOCROSS BIKE
MINIMOTO
™
MOTOCROSS BIKE
MINIMOTO MOTOCROSS BIKE™
Owner’s manual and safety instructions
Carefully read this manual completely
before operating your electric MINIMOTOTM
MOTOCROSS BIKE. Keep this manual in a
safe place for future reference. Be sure
you thoroughly understand how to operate
the components of your MINIMOTOTM
MOTOCROSS BIKE.
NOTE: Throughout this manual there
are many “WARNINGS”. Be sure to
read and understand all of these “WARN-
INGS”. Please pay extremely close atten-
tion to these areas as serious injuryor
even death may result in failing to do so.
Warning: This vehicle is a serious
machine and should be treated with
respect when riding it, working on it, or
simply being near it.
This vehicle can obtain speeds that only
qualified riders of the proper age, size,
and maturity should attempt. That deci-
sion rests entirely on the observation and
discretion of the direct supervising adult.
IMPORTANT!!! Before we begin:
Like any two wheeled vehicle, riding the
MINIMOTOTM MOTOCROSS BIKE can be
extremely hazardous. It is your responsi-
bility to follow this manual for the proper
set up, inspection, riding procedure, pro-
tective gear required, and rules of the road
to reduce the risk of serious injury.
The age recommendation is only an esti-
mate. If the rider is too small, too large,
or too old to comfortably fit on the MINI-
MOTOTM MOTOCROSS BIKE, he/she should
not attempt to ride it. The MINIMOTOTM
MOTOCROSS BIKE is not designed for or
intended to be used byanyone under the
age of 10.
Keep away from small children.
2
FOR WEBSITE INFORMATION
OR REGISTRATION AND CUSTOMER
SERVICE GO TO
www.teamminimoto.com

MINIMOTO
™
MOTOCROSS BIKE
WARNINGS:
This product is meant for outdoor use only
and only on private property. Never ride
your MINIMOTOTM MOTOCROSS BIKE on
public streets, alleys, or other public roads
or thoroughfares. It must never be ridden
in any area that could potentially do harm
to humans, animals, or property damage.
Never ride around the vicinity of small chil-
dren who may enter your path.
Special notes for supervising adults of
the rider:
1) The decision to allow a rider to ride the
MINIMOTOTM MOTOCROSS BIKE must be
done with the permission of a directly
supervising adult. The directly supervising
adult must read and follow all of the con-
tents of the ownersmanual before making
this decision.
2) The rider must have previous experience
in riding two wheeled vehicles without train-
ing wheels before attempting to ride the
MINIMOTOTM MOTOCROSS BIKE. It is the
responsibility of the supervising adult to
ensure the rider has the qualification, phys-
ical ability, and training before allowing
them to attempt to ride the bike.
3) The MINIMOTOTM MOTOCROSS BIKE is
never to be ridden indoors. Indoor flooring
and carpets can be damaged from abrasive
contact with the tires. The manufacturer
will not be responsible for any indoor dam-
age if the MINIMOTOTM MOTOCROSS BIKE is
used in this manner.
4) The MINIMOTOTM MOTOCROSS BIKE is
designed to run on off-road surfaces.
Grass, packed dirt, and moderate off-road
terrain are ideal riding surfaces by persons
over the age of 10.
5) The rider of a MINIMOTOTM MOTOCROSS
BIKE should always wear protective
footwear. Open-toed shoes should never be
allowed. Keep shoe laces and pant legs
away and clear of the wheels.
6) The rider must wear a safety helmet,
elbow and kneepads to avoid injury if
falling. Failure to wear a standard
approved helmet may result in serious per-
sonal injury or death. It is also highly rec-
ommended to wear eye protection while
riding.
7) The MINIMOTOTM MOTOCROSS BIKE is
never to be ridden bymore than one person
at a time. In addition, it is not designed to
pull or tow anything behind it as it may
result in serious damage to the motor or
internal parts. Do not exceed the maximum
capacity of 200 lbs (90 kg).
8) The MINIMOTOTM MOTOCROSS BIKE can-
not be used on wet surfaces or in wet
weather. Never immerse any part of the
MINIMOTOTM MOTOCROSS BIKE in water.
Moisture can damage the motor, switches,
and drive components.
9) The MINIMOTOTM MOTOCROSS BIKE
should never be ridden in mud, water, ice or
snow.It is not designed to be ridden in
streets or on paved surfaces either. Avoid
riding on extreme incline, declines, rocky
surfaces, curbs or jumps.
10) The electric motor can become hot
when in use. Do not touch it at anytime and
handle it carefully.
11) Never use your MINIMOTOTM
MOTOCROSS BIKE while using personal
radios or headphones.
3

MINIMOTO
™
MOTOCROSS BIKE
MINIMOTO
™
MOTOCROSS BIKE
12) Do not use your MINIMOTOTM
MOTOCROSS BIKE for stunt riding, ramp
jumping, running over curbs, acrobatics or
similar activities.
13) Recommended tire pressure is 25 psi.
Never inflate the tires beyond 30 psi.
Inflation of the tires should be performed by
adults only. Use a tire pressure gauge to
ensure pressure of 25 PSI. Serious injury or
death may result in over inflation of the
tires occurs. Avoid filling the tires at a gas
station. The greater pressure of a gas sta-
tion air pump makes a blowout of the tire
possible. This may result in serious injury
or death. Never use NON-MINIMOTOTM
replacement parts.
14) If there is anyproblem or question with
the MINIMOTOTM MOTOCROSS BIKE, please
contact the Minimoto Service Center by
calling the toll free number:
1-800-434-6178
Between the hours of 8 to 7 CST, Monday
through Friday(excluding holidays)
or by email:
customerser[email protected]
Do not return the product to the
store! Contact the Minimoto
Service Center. Authorized serv-
ice is only available through the
official Minimoto Service Center.
Spare tires, inner tubes, batter-
ies, and replacement parts can
be obtained through the
Minimoto Service Center.
15) SB 1918 (CALIFORNIA) DECLARATION:
YOUR INSURANCE POLICIES MAY NOT
PROVIDE COVERAGE FOR ACCIDENTS
INVOLVING THE USE OF THIS PRODUCT.
TO DETERMINE IF COVERAGE IS PROVID-
ED, CONTACT YOUR INSURANCE COMPANY
OR AGENT.
4
TTooyyQQuueesstt
cc//ooMMiinniimmoottooSSeerrvviicceeCCeenntteerr
11880000NN..99tthhSSttrreeeett
IInnddiiaannoollaa,,IIoowwaa5500112255
Customer Service Center:

MINIMOTO
™
MOTOCROSS BIKE MINIMOTO
™
MOTOCROSS BIKE
ELECTRICAL HAZARD:
WARNING
CAUTION!
THIS IS AN ELECTRICALLY OPERATED
PRODUCT AND SHOULD BE OPERATED
WITH CARE. KEEP AWAY FROM SMALL
CHILDREN.
BEFORE RIDING, ALWAYS MAKE SURE
THAT THE BATTERY RETAINER IS FIRMLY IN
PLACE AND HOLDING THE BATTERY
SECURELY.
PREVENTING A FIRE:
a) Never modify the electrical system or
battery charger. Modifications of these
systems can result in fire, serious injury
and damage to the electrical components.
b) To avoid damaging the battery, do not
use the charger if it has been struck,
dropped or damaged in any way.
c) Do not expose the battery to high tem-
peratures as this may cause the battery to
explode.
d) Never allow the battery charger to
become wet or placed in water.
e) Use of the wrong type of battery or
charger could cause a fire or explosion
resulting in serious injury.
f) Never use MINIMOTOTM MOTOCROSS
BIKE parts, battery, or components in any
other products or vehicles other than
those of MINIMOTOTM Motocross BIKE.
Replacing or substituting parts with other
vehicles can result in overheating, fire, or
explosion.
g) The battery is to be handled by ADULTS
ONLY. The battery is heavy and contains a
lead-acid electrolyte. Dropping the battery
can result in serious injury.
h) Never allow children to recharge the
battery. Charging the battery must be
done by ADULTS ONLY. A child could be
injured when involved in the operations of
battery charging or use of electrical
devices.
i) Make sure that all battery contacts or
connectors are clean and free of excessive
wear or damage whenever the battery is
charged. If ANY damage is detected, DO
NOT USE the charger or battery until you
have replaced the worn or damaged part.
j) Always remove the key when not in use
to ensure the power is off and prevent any
unauthorized riders from attempting to ride
the bike.
5

MINIMOTO
™
MOTOCROSS BIKE MINIMOTO
™
MOTOCROSS BIKE
MINIMOTO
™
MOTOCROSS BIKE MINIMOTO
™
MOTOCROSS BIKE
VEHICLE SET UP AND
ASSEMBLY:
CAUTION: The included tools to set up
and charge the MINIMOTOTM MOTOCROSS
BIKE should be used by an ADULT ONLY.
The package contains small parts.
Keep away from small children.
1) Completely remove the MINIMOTOTM
MOTOCROSS BIKE from the packaging.
Position it upright and support it by lower-
ing the kickstand (Fig 1).
2) Find and identify the included tool kit
(Fig 2).
3) Remove the 2 screws from the back
side of the number plate and 2 screws
(1 each side) from the front forks.
Install the number plate in position and
replace screws to their original
spots(Fig. 3A & Fig. 3B).
4) Remove a protective plastic cover
from the end of the steering column. To
do this, first unscrew counter-clockwise
and loosen the bolt using one of the
Allen head keys (Fig. 4).
5) After a few turns of the Allen Key, the
plastic cover should slide off. Throw the
plastic cover away.
6
Fig 1
Fig 2
Fig 4
Fig 3A
Fig 3B

MINIMOTO
™
MOTOCROSS BIKE MINIMOTO
™
MOTOCROSS BIKE
7
6) Slide the steering column into the
front fork (Fig. 5).
7) Adjust the handlebars so they are
square with the front wheel (Fig. 6).
8) FIRMLY tighten the steering column
until the bars do not move. Vertically
adjust height, so that the reinforcement
bar aligns with the recess in the front
number plate (Fig. 7).
WARNING: The handlebars must not
be able to move while riding!. ALWAYS
test the handlebars before riding to
make sure they will not slip, rotate, or
are able to be forced from their desired
position. If the handlebars move while
riding, it is very possible to loose con-
trol and fall. Adjust or tighten the han-
dlebars as necessary.
9) Adjust the throttle by rotating the han-
dle grip into a comfortable position. Use
the allen key to release the screw (Fig.
8). Once the throttle is correctly adjusted,
fasten the screw back on using the allen
key. Make sure the throttle is firmly in
place when finished.
Fig 5
Fig 7
Fig 6
Fig 8

MINIMOTO
™
MOTOCROSS BIKE MINIMOTO
™
MOTOCROSS BIKE
MINIMOTO
™
MOTOCROSS BIKE MINIMOTO
™
MOTOCROSS BIKE
BRAKE ADJUSTMENT:
IMPORTANT! Inspect and check the
adjustment of the hand brake before
attempting to ride on your MINIMOTO™
MOTOCROSS BIKE.
Minor Brake
adjustment
The brakes will
need to be
adjusted over
time. Tightening
or loosening the
brake adjust-
ment knob can
obtain minor
brake adjust-
ments. This
knob is located
next to the hand
brake. To do this
adjustment,
loosen the nut
and turn the conical shaped knob to adjust
the brake (Fig. 9). Retighten the knob
with the nut when the appropriate feel of
the brake is found (Fig. 10).
Major Brake adjustment
If the brakes
need a more
drastic adjust-
ment, use the
wrench to
loosen the nut
that connects
the cable to the
rear wheel (Fig.
11). When the
nut is loosened,
pull the brake
cable tight until
there is no
slack in the
cable. Retighten
the nut securely
(Fig. 12) and
check the
brakes again before riding.
IMPORTANT!
In the event of extraordinary heat or tem-
porary malfunction of the brake after a pro-
longed or aggressive use, stop riding the
bike immediately. Call the Minimoto
Customer Service Center at the Toll-free
number before further use.
8
Fig 9
Fig 10
Fig 11
Fig 12

MINIMOTO
™
MOTOCROSS BIKE MINIMOTO
™
MOTOCROSS BIKE
9
BATTERY CHARGING
INFORMATION:
IMPORTANT: The new battery provided in
the MINIMOTOTM MOTOCROSS BIKE
MUST BE charged for at least 12 hours
before using for the first time.
The charger MUST be used only in a clean,
dry indoor area. In addition:
.Battery charging must be done by
ADULTS only.
.The battery must be upright when
charging.
.The charger is not a toy.
.Do not short-circuit the battery.
.Do not charge the battery on any deli-
cate surfaces (such as a counter top).
.Only use the provided charger to charge
the battery.
.Only use a MINIMOTOTM MOTOCROSS
BIKE battery or batteries.
.Remove old or dead battery from the
MINIMOTOTM MOTOCROSS BIKE if it
does not accept a charge.
.Never use the charger in an enclosed
space. Always ensure adequate venti-
lation.
.Never cover the MINIMOTOTM
MOTOCROSS BIKE or the charger dur-
ing charging.
.Should anything abnormal happen to
the MINIMOTOTM MOTOCROSS BIKE or
charger, switch off the mains supply
immediately and contact the Minimoto™
Service Center.
IMPORTANT:
Under normal conditions, the battery will
reach full charge in 8 to 20 hours of charg-
ing time. The difference in time depends
on the local power output in your area, the
type of outlet you use, and the condition of
the battery.
NOTE: Plug the charger directly into a
standard wall outlet. Do not connect the
charger to a surge protector. Surge protec-
tors can slow down the charging process.

MINIMOTO
™
MOTOCROSS BIKE MINIMOTO
™
MOTOCROSS BIKE
MINIMOTO
™
MOTOCROSS BIKE MINIMOTO
™
MOTOCROSS BIKE
STEPS TO CHARGE BATTERY:
The charging port is located on the upper
body. It resembles a simulated ”FUEL
CAP”.
1) Lift up the protective cover of the
charger port(Fig. 13).
2) Plug the charger into the port.
Note that the charging port has a “rib”
inside(Fig. 14). This allows the plug to
be inserted in the proper orientation to the
port.
3) Plug in the charger into a standard
electrical outlet.
4) THE RED LED indicator light on the
charger will be ON when charging properly.
5) The GREEN LED will come on when the
battery is fully charged.
6) Remove the charging plug and close
the protective cover after charging the bat-
tery.
NOTE: It is recommended that you always
recharge the battery for a period of 8
hours. However, 80% of the power will be
charged into the battery in 4 hours. It is
possible to use the MINIMOTOTM
MOTOCROSS BIKE after this period but the
total running time will be reduced.
10
Fig 13
Fig 14
Country Input Output Polarity Shape
A.C. 100-120V
60Hz
d.c. 36V 2000mA
U.S./Canada
Taiwan/Japan
A.C. 220-240V
50Hz
d.c. 36V 2000mA
U.K./Hong Kong/
Singapore/Malaysia/
Africa
A.C. 220-230V
50Hz
d.c. 36V 2000mA
Europe/Germany/
Israel
A.C. 240V 50Hz d.c. 36V 2000mA
Australia/
New Zealand/China
Bare
Bare
Bare
Bare
Battery Charger specifications for world-wide standard:

MINIMOTO
™
MOTOCROSS BIKE MINIMOTO
™
MOTOCROSS BIKE
BATTERY CARE:
If a battery appears to be leaking, avoid
contact with the leaking materials. Place
the battery in a plastic bag.
WARNING: This liquid and contents of the
battery are highly acidic. Wash your hands
immediately and thoroughly for a minimum
of 15 minutes. Call a physician. Do not
touch your face or eyes. If acid is inter-
nally ingested, IMMEDIATELY give water,
milk, egg whites, or milk of magnesia.
Never give emetics or induce vomiting.
CALL A PHYSICIAN IMMEDIATELY.
.Use ONLY a MINIMOTOTM MOTOCROSS
BIKE battery.
.Never charge the battery for more than
30 hours.
.Charge the battery after each use.
.Avoid running the battery completely
as this will greatly shorten their use-
able life.
.Never leave the battery in an
uncharged condition. This will perma-
nently damage it and prevent it from
being able to hold any charge.
.Disconnect the battery from the wiring
if the MINIMOTOTM MOTOCROSS BIKE
is to be stored more than 2 months.
.Do not store the batteries in tempera-
tures above 122 degrees F or lower
than 32 degrees F.
.Check to make sure the battery is
secure before riding the bike. Tighten
the battery retainer if necessary.
11

MINIMOTO
™
MOTOCROSS BIKE MINIMOTO
™
MOTOCROSS BIKE
MINIMOTO
™
MOTOCROSS BIKE MINIMOTO
™
MOTOCROSS BIKE
HOW TO REPLACE
THE BATTERY:
1) Remove the key from the
lock.
2) Remove the two bolts on
top of the seat and one bolt
under the seat with the
allen key and wrench (Fig.
15).
3) Using the allen key
remove two bolts, on both
sides of the body that holds
the body to the frame. (Use
the provided wrench to help
when removing the two rear
bolts.) (Fig. 16).
4) Remove the seat and body
from the frame work (Fig.
17).
5) Remove four screws on
the driver’s right and one
screw on the driver’s left of
the silver body halves using
the screwdriver (Fig. 18A &
Fig. 18B). Use the wrench
to help removing the rear
screws. Separate the body
halves from the bike (Fig.
19).
6) Remove the seven
screws that hold the battery
box together with the screw-
driver (Fig. 20). Remove
the driver’s left side first.
7) Remove the two bolts
that holds the right half of
the battery box to the chas-
sis with the allen key (Fig.
21).
8) Remove the battery box
(Fig. 22).
12
Fig 16 Fig 18B
Fig 18A
Fig 15
Fig 17
Fig 19
Fig 20
Fig 21
Fig 22

MINIMOTO
™
MOTOCROSS BIKE MINIMOTO
™
MOTOCROSS BIKE
9) Loosen and remove the
four screws on the battery
retainer with the help of the
wrench to hold the nut
beneath the chassis (Fig.
23). Carefully disconnect
the electrical plug between
the battery and the wiring
hardness.
10) Remove the battery
and replace it with a fresh
battery.
11) Reconnect the plugs
and position the wires to
exit the proper hole from
the battery box (Fig. 24).
12) Retighten the battery
retainer so the battery is
securely held.
13) Replace the battery
box, and lower body in
reverse order.
14) Charge the new battery
before attempting to ride
again.
Note:
Use only MINIMOTOTM
replacement batteries.
. Non-rechargeable battery
is not to be charged.
. Battery charging must
be done by ADULTS
only.
. Only battery of the same
or an equivalent type as
the recommended
battery is to be used.
• Battery is to be insert
with the correct polarity.
• If battery does not accept
a charge, remove the old
or dead battery from the
MINIMOTOTM MOTOCROSS
BIKE.
• Do not short-circuit the
battery and the
connectors.
13
Fig 23
Fig 24

MINIMOTO
™
MOTOCROSS BIKE MINIMOTO
™
MOTOCROSS BIKE
MINIMOTO
™
MOTOCROSS BIKE MINIMOTO
™
MOTOCROSS BIKE
BATTERY DISPOSAL:
Always return your unwanted batteries to a
local federal or state approved lead-acid
recycling center or an authorized automo-
bile battery seller. For residents in the
states of Florida and Minnesota, it is ILLE-
GAL for anyone to attempt to dispose of
lead-acid batteries in a municipal waste
stream.
Always dispose of unwanted or used
batteries in a safe and environmentally
friendly manner. DO NOT throw the batter-
ies into your regular household trash. Law
prohibits the disposal of lead-acid batter-
ies by incineration, placing them in a land-
fill, or mixing them with other rubbish.
NEVER expose the batteries to FIRE. The
batteries may leak or explode.
14

MINIMOTO
™
MOTOCROSS BIKE MINIMOTO
™
MOTOCROSS BIKE
RIDING RULES:
DIRECT ADULT SUPERVISION IS REQUIRED
WHEN RIDING.
Adults should teach the appropriate safety
rules and methods before allowing anyone
to ride the MINIMOTOTM MOTOCROSS BIKE.
The rules should be reviewed with any chil-
dren in the vicinity that may want to ride
the MOTOCROSS BIKE.
1) The following areas are to be avoided
when riding the MINIMOTOTM MOTOCROSS
BIKE:
a. Cars or traffic
b. Streets or alleys
c. Steps or steep inclines
d. Swimming pools, puddles, ice, or
bodies of water
e. Any area that could potentially
cause harm to humans, animals, or
property. Ride only in areas where
permission has been granted.
2) Do not use on roads or public streets,
as this is illegal and dangerous.
3) Never ride the MINIMOTOTM
MOTOCROSS BIKE at night.
4) Never ride with more than one rider.
Maximum allowable weight of the rider
should not exceed 200 lbs (90 kg).
5) Always wear appropriate shoes, cloth-
ing,and protective gear. Protective gear
includes the use of a helmet, knee pads,
and elbow pads (not included).
6) Always check to see that the kick stand
is in the up position before starting to
ride. Leaving the kick stand in the down
position can cause the rider to fall while
riding.
7) Do not use the MINIMOTOTM
MOTOCROSS BIKE for jumping, stunts or
tricks. This product has not been
designed for such use.
8) Do not touch the motor or wheels while
it is rotating.
9) Keep hands, face, feet and hair away
from all moving parts.
10) Do not ride down or across steep
inclines. The MINIMOTOTM MOTOCROSS
BIKE, just like a bicycle, can reach unsafe
speeds, loose traction, or slip and tip over.
11) Never ride near flammable liquids or
vapors such as gasoline, acetone or paint
thinner. Keep all flammable materials
away from the MINIMOTOTM MOTOCROSS
BIKE.
12) Never wear headphones or use a cell
phone when operating.
13) Ride defensively. Remember that oth-
ers around you may not see you or may be
to involved in their own actions.
14) Learn about and observe your local
laws regarding bicycle use.
15) Riders must be over the age of 10.
Keep away from small children.
15

MINIMOTO
™
MOTOCROSS BIKE MINIMOTO
™
MOTOCROSS BIKE
MINIMOTO
™
MOTOCROSS BIKE MINIMOTO
™
MOTOCROSS BIKE
PRE-RIDE CHECKLIST
Your MINIMOTOTM MOTOCROSS BIKE is just
like any vehicle. It requires routine mainte-
nance, service, and inspection to operate
reliably and safely.
.Look over the entire unit to ensure
that there are no visible problems with
the MINIMOTOTM MOTOCROSS BIKE.
.Check that the handlebars are tight.
.Check the tires, ensuring there are no
cuts or exposed cords or the tires are
deflated.
.Check that all cables and wires are not
frayed, cut or broken.
.Check that the brake lever is tight on
the handlebar.
.Pull the brake lever to make sure that:
1. The brake releases automatically.
2. The brake holds the electric
minibike from being pushed
forward.
.Check that the throttle is tight on the
handlebar.
.Check that all 4 axle nuts are tight and
the wheels do not wobble .
16

MINIMOTO
™
MOTOCROSS BIKE MINIMOTO
™
MOTOCROSS BIKE
HOW TO RIDE YOUR
MINIMOTOTM MOTOCROSS
BIKE:
NOTE: It will take a little practice to get
used to riding. Take it slowly and start in
a location that is very open and away from
obstacles or obstructions.
1) Place the foot pegs in the down posi-
tion (Fig. 25).
2) Move the kickstand up while holding on
to the handlebars(Fig. 26). WARNING:
Failure to move the kickstand to the up
position before moving the throttle control
may result in
damage to
the kickstand
or crashing
the bike.
3) With feet on the ground, balance bike
between legs.(Fig. 27).
4) Place the
key in the lock
and turn it
clockwise to
the ON posi-
tion (Fig.
28).
5) With the right hand, rotate the throttle
control slowly and precisely (Fig. 29). AT
THE SAME
TIME lift your
feet up from
the ground.
6) When you have achieved enough speed
to balance, place your feet on the foot
pegs (Fig. 30).
7) Rotate the
throttle con-
trol handle
(on your right
hand side) to
increase
speed.
Squeeze the brake lever with left hand to
apply the brake to slow or stop.
8) BE CAREFUL: The MINIMOTOTM
MOTOCROSS BIKE can reach speeds up to
15 MPH on a level surface (depending on
the surface terrain and the weight of the
rider).
17
Fig 25
Fig 26
Fig 27
Fig 28
Fig 29
Fig 30

MINIMOTO
™
MOTOCROSS BIKE MINIMOTO
™
MOTOCROSS BIKE
MINIMOTO
™
MOTOCROSS BIKE MINIMOTO
™
MOTOCROSS BIKE
SPECIAL SAFETY WARNINGS
1) When accelerating please ensure that
you start smoothly & evenly. Do not push
away for a quick start.
2) The brakes are designed to control
speed as well as stop the vehicle.
Practice braking for slow-down and smooth
stopping.
3) Never operate the throttle control when
the wheels are off the ground or the
Motocross bike in an upside down
position.
4) Make sure the key is removed from the
bike when the bike is not in use.
18