MINN KOTA ENDURA C2 User manual

,n
ETUDURA Cz
TnnusoM-Mouur TnoLLING Moron
Owner's Manual

NOTE: Do not return your Minn Kota motor to your retailer. Your retailer is not authorized to repair or replace this unit. You
may obtain service by: calling Minn Kota at [phone] or [phone]; returning your motor to the Minn Kota Factory
Service Center; sending or taking your motor to any Minn Kota authorized service center on enclosed list.
Please include proof of purchase, serial number and purchase date tor warranty service with any of the above options.
Please thoroughly read this user manual. Follow all instructions and heed all safety and cautionary notices below Use of
this motor is only permitted for persons that have read and understood these user instructions. Minors may use this motor
only under adult supervision.
ATTENTION: Never run the motor outside the water, as this may result in injuries from the rotating propeller. Connect motor
to battery only if motor is in operating position and the speed-control is in the zero position. Remove power supply from
motor before tilting motor up and propeller out of the water. When connecting the power-supply cables of the motor to the
battery take care that they are not kinked or subject to chafe and route them in such a way that persons cannot trip over
them. Before using the motor make sure that the insulation of the power cables in not damaged. Dsregarding these safety
precautions may result in electric shorts of batt€ry(s) and/or motor. Always disconnect motor from battery(s) before cleaning
or checking the propeller. Avoid submerging the complete motor as water may enter the lower unit through control head and
shaft. lf the motor is used while water is present in the lower unit an electric short will occur and considerable damage to the
motor will be the consequence. This damage will not be covered by warranty. l
CAUTION: Take care that neither you nor other persons approach the tuming propeller too closely, neither with body parts
nor with objects. The motor is powerful and may endanger or injure you or others. While the motor is running watch out
for persons swimming and lor floating objects. Persons whose ability to run the motor or whose reactions are impaired by
alchohol, drugs, medication, or other substances are not permitted to use this motor. This motor is not suitable for use in
strong currents. The constant noise pressure level of the motor during use is less than 70dB(A). The overall vibration level
does not exceed 2,5m/sec2.
Model:
Serial Number:
Purchase Date: I ,i:r
Store Where Purchased:

FEATURES
Adjustable Depth Collar +
Multi Position Mounting Bracket
1
Handle controls on/off, speed,
forward/reverse and direction
F Quick Release Tilt Lever
g Lifetime Warranty
Flexible Composite Shaft
Weedless Propeller
J
Cool Power'M Motor Runs Stronger
Specifications subiect to change without notice.

HANDLE INSTALLATION
Remove the wire clip from the balldetent located on the inner handle.
lnstall outer handle over inner handle. Position the handles so the detent ball and OFF are aligned.
Push the outer handle into the control box until handle "clicks" into place. The handle is held in
place with locking fingers, so some force may be required to lock the handles together.
Once the handle is locked into the control box, it can be rotated and extended for normal use.
Once the handle is installed, the assembly is permanent. Do not attempt to remove the handle.
MOTOR INSTALLATION
Mount the Motor:
. lnstallthe motor on the transom ol the boat. Be sure to tighten the clamp screws securely.
Depth Adjustment:
. Firmly grasp the composite shaft and hold it steady.
. Loosen the steering tension knob and depth collar knob untilthe shaft slides freely.
. Raise or lower the motor to lhe desired depth.
. Tighten depth collar knob to secure the motor in place.
NOTE: When setting the depth be sure the top ol the motor is submerged at least 12" to avoid churning
or agitation of surface water. The propeller must be completely submerged.
GAUTION:
. Never operate your motor when it is out of the water.
. Over-tightening the clamp screws can damage the bracket.
Steering Adjustment:

I
ADJUSTMENTS
Adjust the steering tension knob to provide enough tension to allow the motor to turn freely, yet
remain in any position without being held or
Tighten the knob to place the motor in a preset position to leave your hands free for fishing.
Bracket Adjustment:
You can lock your motor in a vertical position, angle it for shallow water or tilt it completely out of the
water.
. Firmly grasp the control head or composite shaft.
. Depress and hold the tilt lever.
. Tilt to any of the positions on the mounting bracket.
. Release the tilt lever.
WARNING: When raising/lowering motor or operating the tilt mechanism, keep fingers clear of
all hinge and pivot points and all moving parts.
OPERATION
Twist Tiller:
These motors offer a choice of five forward and three reverse speeds. The speed control may be
operated in either direction, forward or reverse. Turn the tiller handle counterclockwise from (OFF) to
increase reverse speed and clockwise from (OFF) to increase forward speed. Thrust decreases as you
approach (OFF) from either direction.
These motors will operate with any deep cycle marine 12 volt battery. For best results, use a deep
Depth Adjustment Knob
Steerin g Ten sion 5-crew
Quick ReleaseTllt Lever
Clamp
/,"'"''