Minoston MP31ZP User manual

ITEM INFORMATION
Model MP31ZP
Power Supply AC 120V 60HZ
Signal(Frequency) 908.42MHz
Operating Temperature Range 5-104° F (-10-40° C)
GENERIC_TYPE GENERIC_TYPE_SWITCH_BINARY(0x10)
SPECIFIC_TYPE SPECIFIC_TYPE_NOT_USED(0X00)
Command Class Name Version Required Security Class
Z-Wave Plus Info V2 none
Security 2 V1 none
Supervision V1 none
Transport Service V2 none
Basic V2 highest granted
Association V2 highest granted
MP31ZP User Manual V1.20
Specifications
Button Function Description
1. Add or Remove the device
press 3x Button : Add/Include or Remove/Exclude the device into network.
2. Factory Reset
press twice and then press and hold the button for about 10 seconds until the BLUE indicator flashes.
Adding Your Device To Hub
The device support two methods of inclusion, When using a Z-Wave Plus ™ certified controller choose Network
Wide Inclusion or Smart Start.
Network Wide Inclusion To A Z-Wave ™ Network
Refer to your primary controller instructions to process the inclusion / exclusion setup procedure.
When prompted by your primary controller, click the z-wave button three times .
The device is compatible with Smart Start.
Smart Start enabled products can be added into a Z-Wave ™ network by scanning the Z-Wave QR Code found on
the top of the outlet or the back of the box with a controller providing Smart Start inclusion. No further action is
required and the Smart Start product will be added automatically within 10 minutes of being switched on and in the
network vicinity. .
Command Class
MP31ZP User Manual
No. 1 / 4

Command Class Name Version Required Security Class
Association Group Information V3 highest granted
Multi Channel Association V3 highest granted
Version V3 highest granted
Manufacturer Specific V2 highest granted
Device Reset Locally V1 highest granted
Power Level V1 highest granted
Indicator V3 highest granted
Firmware Update Meta Data V5 highest granted
Configuration V4 highest granted
Notification V8 highest granted
Meter V5 highest granted
Switch Binary V2 highest granted
Type Event
Power Management(0x08) Over Current Detected(0x06)
Power Management(0x08) Over Voltage Detected(0x07)
Power Management(0x08) Over Loaded Detected(0x08)
Base Type Type Scale Precision Overload Threshold
Electric Current A 2 16.5A
Electric Voltage V 2 135.0V
Electric Power W 1 2000W
Electric Electricity KWH 3 ----
Notification
Meter
Indicator Command Class
Indicator ID Property ID
0x50 (NODE IDENTIFY) 0x03(ON OFF PERIOD)
0x50 (NODE IDENTIFY) 0x04(ON OFF CYCLES)
0x50 (NODE IDENTIFY) 0x05(ONE TIME ON OFF PERIOD)
The indicator (blue color) will flashes according the indicator set command received from HUB.
MP31ZP User Manual
No. 2 / 4

ID Name Node Count Profile Function
1 Lifeline 5 General: Lifeline
Device Reset Locally Notification:
Issued when Factory Reset is performed.
Indicator Report:
Issued when included successfully.
Switch Binary Report:
Issued when output status is changed.
Notification:
Issued when current, voltage or power is overload
Meter report:
Issued when current, voltage or power is overflow
the threshold.
2 Basic Set 5 Control: Key 1 Basic Set :
Issued when local state is changed
Number Name Information Size MIN MAX Default Value Description
1 Reaction of led Change the reaction of the
indicator. 1 byte 0 3 0
0 - On when On and Off
when Off
1 - On when Off and Off
when On
2 - Always Off
3 - Always On
2 Auto Turn Off Minutes for turn off
automatically. 4 bytes 0 65535 0
0-Disable
1- 1 minute
...
65535-65535minutes
3 Auto Turn On Minutes for turn on
automatically. 4 bytes 0 65535 0
0-Disable
1- 1 minute
...
65535-65535minutes
4 Status Restore Restore status after power
failure. 1 bytes 0 2 0
0 - restore last state
1- Always off
2 - Always on
5Report threshold of
power Threshold for power report(W). 1 byte 5 50 5
5 - 5W
...
50 - 50W
6Report frequency of
power
Interval minutes after last report
of power.. 4 bytes 1 65535 5
1- 1minute
2- 2minutes
...
655535 - 65535minutes
7Report threshold of
currents
Threshold for currents
report(x0.1A). 1 byte 1 10 1
1 - 100mA
2- 200mA
...
10 - 1A
8Report threshold of
electricity
Threshold for electricity
report(x0.01KWH). 1 byte 1 100 1
1 - 0.01KWH
2 - 0.02KWH
...
100 - 1KWH
9 Indicator brightness Setting indicator's brightness. 1 byte 0 2 2
0 - High level
1 - Mid level
2 - Low level
10 Disable power report Enable or disable power report. 1 byte 0 1 0 0 - Enable power report
1 - Disable power report
11 Disable currents report Enable or disable currents
report. 1 byte 0 1 0 0 - Enable power report 1 - Disable power report
12 Report frequency of
currents
Interval minutes after last report
of currents. 4 bytes 1 65535 60
1- 1minute
2- 2minutes
...
655535 - 65535minutes
Association Group
Configuration Parameters
MP31ZP User Manual
No. 3 / 4

Number Name Information Size MIN MAX Default Value Description
13 Report frequency of
voltage
Interval minutes after last report
of voltage. 1 byte 0 65535 60
0 - Disable report
1- 1minute
2- 2minutes
...
655535 - 65535minutes

MP31ZP User Manual
No. 4 / 4