Minuteman PORT A SCRUB Guide

M12110
M12230
Port A Scrub
Floor Scrubbing Machine
Instruction Manual & Spare Parts List

Contents
Instruction Manual
Product information...................................................................................................
Important safety instructions.....................................................................................
Technical specification..............................................................................................
Know your machine...................................................................................................
Working principle.......................................................................................................
Preparing for use.......................................................................................................
Assembly...................................................................................................................
Brush selection guide................................................................................................
Controls.....................................................................................................................
Operating the machine..............................................................................................
Electrical diagram......................................................................................................
Accessories...............................................................................................................
Upkeep of your PORT A SCRUB...............................................................................
Spare Parts Manual
Housing - Drive Side.................................................................................................
Housing-Idle Side......................................................................................................
Pump housing...........................................................................................................
Lever and guide link mechanism...............................................................................
Handle group.............................................................................................................
Motor,drum and bridge assembly..............................................................................
Accessories...............................................................................................................
3
3
4
5
5
5
6
6
7
7
8
9
9
10
12
16
18
19
21
23

The Minuteman PORT A SCRUB is an ideal machine to clean floors in small and medium areas like offices, ospitals,
restaurants, shopping complexes and many commercial applications. It sprays plain water / detergent solution, scrubs
and picks up the dirty water - all in a single pass. The Port A Scrub has different optional brushes to suit a variety of
applications. This machine can be used only on smooth even floors like Mosaic, all type of stone floors, PVC, Short-pile
carpet, Wood and Profiled Rubber. It should not be used on rough uneven surfaces.
Product Information
Important Safety Instructions
Instruction Manual
The machine must be unpacked and assembled in accordance with these instructions before connecting to the
electrical supply.
·This machine should always be connected to a fully grounded power supply of the right voltage and frequency.
·Keep the power supply cord away from moving parts. During operation, hazard may occur when running machine
over the supply cord.
·The machine must be disconnected from the mains supply (by pulling the plug out) before changing the brushes,
cleaning the machine and, for maintenance.
·Warning! Use only the brushes/accessories strictly as per the instruction manual. Usage of any other
brushes/accessories can cause safety problems.
·Periodically inspect the cord for possible damage. The damaged cord must be replaced with the special cord
available from the manufacturer or an authorized service agent.
·DO NOT leave the machine connected to the power supply when not in use; always remove the plug from the mains
socket.
·DO NOT use where hazardous dust is present.
·DO NOT use machine near flammable liquids.
·DO NOT use in an explosive atmosphere.
·DO NOT use in gradient surface.
·DO NOT keep the machine with handle lowered, when the machine is in working mode.
Guidelines for the operator
·Operators must be fully trained in accordance with these instructions, able to perform routine upkeep of the machine
and correct selection of brushes.
·Operators should be physically capable to maneuver transport and operate the machine.
·DO NOT run the machine dry, as this could damage the floor surface or the machine itself.
·Take adequate care to hold the machine firmly while installing and removing the brush.
·Never use excessive foaming or highly corrosive cleaning solutions.
·While operating on a flooded floor, always ensure that the water level does not exceed 1/4”.
·DO NOT operate this machine on rough uneven surface like industrial concrete floor.
·Do not clean the machine using water jet.
·Ensure all parts are fitted properly before operation.
3
Please read the following instructions completely before operating the machine. Any violation of the same will
not only invalidate the warranty, but also may result in a safety hazard.

Technical Specification
Note:
1. Noise levels measured at a distance of 1 meter from machine and 1.6 metres above floor, when washing a hard floor. Measurements recorded using a hand held meter.
2
2. Handle vibration does not exceed 2.5 m/s , when operating on a smooth hard surface.
3. Above dimensions are approx. Since the companies policy is to continuously improve the product, there could be changes without prior notice.
Description Units Specification
Model -- M12110
Mains supply -- 100-110 VAC±% 60Hz, Single Phase
Power W 750
Brush Speed rpm 780
Cleaning Capacity 2 ft /hr 3,800
Cleaning Width inch 12.5
Fresh water tank capacity gallon 1
Overall Dimensions
Height with handle inch 43.75
Height without handle inch 8.25
Width inch 17.32
Length inch 14.88
Weight lbs 55
Noise level (see note) dB(A) 69
Handle vibration (see note) 2 m/s <2.5
Description Units Specification
Model -- M12230
Mains supply -- 230 VAC±% 50Hz, Single Phase
Power W 600
Brush Speed rpm 650
Cleaning Capacity 2 ft /hr 3,800
Cleaning Width inch 12.5
Fresh water tank capacity gallon 1
Overall Dimensions
Height with handle inch 43.75
Height without handle inch 8.25
Width inch 17.32
Length inch 14.88
Weight lbs 55
Noise level (see note) dB(A) 69
Handle vibration (see note) 2 m/s <2.5
4

Know your machine
Working Principle
Preparing for use
(1) Top handle
(2) Liquid discharge control
handle
(3) Tank
(4) Bottom handle
(5) Dirty water tank
(6) Filter
(7) Lid Cap
(8) Boot
(9) Nozzle
(10) Conveyor drum
(11) Brush
(12) Pedal
1. Cleaning liquid in the fresh water tank is made to spray on the
floor to be washed.
2. The counter rotating brushes scrubs the floor and also throws
the dirty water on the Conveyor drum. The front brush does most
of the scrubbing and drying. The rear brush completes the
scrubbing and collects the remaining water of the floor.
3. A blade fitted to the dirty water tank wipes the drum and collects
the dirty water.
1. To save packing space and to ensure the safety of the
machine during transporting, the PORT A SCRUB comes to
you with its handle dismantled. Ensure that the listed parts
are present as shown and identify them in order to
understand the assembly instructions.
2. Remove the hook which holds the bottom handle with the
machine body while holding the bottom handle.
Front
Warning! Since the bottom handle is spring loaded, the casual removal of the hook may result in
sudden springing back leading to possible injury to personnel.
1. Bottom handle
2. Machine body
3. Pump Housing
4. Auxillary Tank
5. Top handle &
pull cable
6. Handle LH & RH
7. Brush shafts (2)
8. Screws & washers
9. Cable retainer
10. Power cord
11. Dirty water tank
12. Hook
13. Knob
10
9
8
6
7
13
5
11 4
1
2
3
12
(10)
(11)
(12)
(7)
(8)
(9)
(6)
(2)
(3)
(4)
(5)
(1)
5

Assembly
Brush Selection Guide
1. Insert the two tubular handles into the bottom handle and secure them using knob (2 Nos)
by tightening lightly. Ensure that the handles are assembled according to their marked
position and the cable holding hooks are pointing towards the rear.
2. Slide the electric cable retainer into the top portion of RH handle.
3. Fit the top handle over the tubular handles and secure them with washer and screw (2 sets).
Ensure that the label on the top handle is facing the front of the machine. Now tighten
firmly both the knobs and screws alternately. Insert the dummy caps provided to cover the
screws (2 nos) in the top handle.
4. Pass the free end of the pull cable through the plastic guide in RH Handle.
5. Fix the auxillary tank firmly into the bottom handle by holding the top handle.
6. Rotate the knob to hold the auxillary tank.
7. The brushes are only loosely packed in the machine for transit, therefore the brush shafts
must be fitted before operating the machine. Push the shafts through the brushes from the
side of the machine. To remove brushes, push the brush shaft out from the side of the
machine using the fingers and withdraw the shaft. Normally standard brush type will be
supplied with the machine. Brushes shall be selected according to the type of floor surface
to be cleaned, and the degree of dirt to be removed, please refer Brush Selection Guide.
8.Now machine is ready for use.
6
All natural stone floors,
Ceramic, Mosaic, Wood,
Profiled rubber, Vinyl, PVC,
Standard Soft
Short pile carpet
Marble Granite
Smooth concrete
Escalator
Others
Soft
Soft
Hard
Escalator
To suit individual floor conditions
Soft
Soft
Standard
Escalator
Type of floor First time cleaning Maintenance cleaning
Refer Page 25 for Brush
Selection
L E F T
B O T T O M
R E A R
R I G H T
B O T T O M
R E A R
Brush identification
This is applicable when the customer has more than one set of brushes of same type.
Example : 2 or more sets of Standard Brush
Customers may not interested to use same brushes in Bedroom / Kitchen / germ free area
which is already been used in other areas like Corridor / Bathroom / Oil or chemical
deposited areas. It is difficult for the customers to identify the particular brush which is
used in certain area. To make this easy, Brush buttons of colors RED, BLUE, WHITE and
YELLOW are packed with the machine. Customers shall plug the buttons on the hole
provided in the brush as shown. This helps the customer to identify the particular brush by
keeping the button (color) as reference.
(a) (b)
(a) Hole provided for plugging button.
(b) Brush with button plugged.

By pressing the pedal lightly with your
foot, pull back the handle a little to start
the motor. The brushes and the drum
starts rotating. Pulling the handle further
without pressing the pedal, lowers the
machine and engages the rotating
brushes onto the floor. To stop working,
take the handle to the vertical position.
By pulling, the liquid discharge control
handle up, the cleaning liquid is made to
spray on the floor. The spraying stops
once the liquid discharge control handle
is released.
Brush contact with the floor is
adjustable in 4 steps, contact is
MINIMUM when the knob is fully down
and MAXIMUM when it is fully raised.
This helps you to compensate for the
wear of brushes and also to control the
scrubbing effect. If there is no machine
movement, when the handle lower
down fully (working mode), change the
knob position to one step up.
In the event of motor getting overloaded
due to improper power supply or
u n e x p e c t e d o b s t r u c t i o n t o t h e
brush/drum rotation, the over load
protector trips and protects the motor
from damage. If this happens, identify the
cause, correct it and, reset the protector
button after minimum 30 seconds from
tripping by pressing the over load
protector manually and continue working.
Slide this knob to TOP position to
operate the machine. Slide this knob to
BOTTOM position to move the machine
from one place to other place and to
park the machine. By keeping the knob
to top position (working mode) and
moving the machine will damage the
brushes.
Controls
Operating the machine
Before the washing operation starts
Recommended washing sequence
On/Off Control Transport/Working Model Control
Brush Contact Control Cleaning Liquid Discharge Control
Motor Overload Protector
1
2
OFFON
BEFORE
R E S E T
W A I T
S E C O N D S
30
!
P R E S S
Warning! should the machine fail to operate,
contact the supplier from whom you purchased
the machine.
Warning! Precleaning of floor is must before using the PORT A SCRUB.
1. Fill cleaning liquid in fresh water tank (Fig-I)
2. Insert the plug into mains 3-pin socket.
3. Ensure that the brushes are fitted properly.
4. Slide the transport/working mode control knob to TOP
(working) position (Fig-ii).
1. Start the machine by pressing the pedal and pulling the handle back.
2. Move forward, while sparingly pulling the liquid discharge control handle (Fig-iii). This handle should not be kept
pulled all the time. The duration and frequency of pulling and releasing has to be adjusted suitable to match with the
type of floor, extent of dirt. etc. For ceramic & granite floors, apply very little water.
(i)
ON
3
2
1
OFF
(ii)
7

Care of the machine
3. Stop the liquid discharge approximately one foot before the end
of forward motion. continue to move forward up to the wall without
pulling the pull handle .
Spray angle / area can be controlled by the user according to their
requirements. It also prevents water / solutions sprayed in the
cleaned area. Spray angle of the solution is made to adjust using
the serrations provided in the nozzle and the nozzle holder. Nozzle
can be rotated about 28 degrees either clockwise or counter
clockwise @ the increment of 4 degree (Fig-i v).
4. Pull the machine backwards in the same track, but without
discharging any liquid. When you are reaching the starting
point, change the track and repeat steps 2 through 4. When you
are changing the track allow some overlap with the cleaned area.
In case of large halls take a U-turn and move forward. If quick
drying is desired, move on the same track, without discharging
the liquid (Fig-v)
5. When the dirty water tank is full, lift and pull the tank out of the
machine (Fig vi). Empty the tank and wash it in running water or
dip it in a bucket of water (Fig-vii). Clean the blades and push the
tank into its place.
1. Move the Transport / Working mode control knob to
BOTTOM (Transport) position (Fig-viii).
2. Disconnect the power supply by unplugging the electrical
plug and wind the cable over cable holders in the handle.
3. Pull out the dirty water tank and wash it completely.
4. To prevent possible clogging of filter, drain cleaning liquid
5. Remove the brushes by pushing the brush shaft out (Fig-
ix).
(a)
(b)
(v)
(a) Recommended pattern for
small rooms
(b) Recommended pattern for
large halls
Electrical Diagram
Abbreviations given in the diagram as listed:
Warning! Before undertaking the cleaning operations switch off the machine and unplug from the electrical
supply.
Warning! Any service or attempt to service by
persons other than authorised servicing agent
is not recommended.
Warning! Avoid touching the sharp edge of dirty water tank. it may cause injury to hands.
(iii)
(vi)
(vii)
(viii) 3
2
1
(ix) (x) (xi)
CAPACITOR
928748
SC
BK
R
W
BR
BR
MOTOR
BR
BL
BL
BR/W
BL/BK
G/Y
N
RC
CBE
BR/W
BL/BK
PUMP
BR/W
BL/BK
(iv)
1. Nozzle
2. Nozzle holder
(a)
(a) Nozzle at normal position
(b) Nozzle at rotated position
(c) Nozzle inserted inside the holder
at rotated position
(b) (c)
Abbreviation/Symbol Description
6. Wash the brushes either by dipping in a bucket/sink or
in running water (Fig-x).
7. Turn the machine sideways and wipe clean the
conveyor and machine body with a damp cloth (Fig-xi).
8. Re-install the brushes after washing. It is easier to push
the brush shaft form the right hand side (identified by
the electrical cable).
9. Keep the machine in the safer place.
CBE
BR
BL
W
BK
R
Circuit Breaker
Brown
Blue
White
Black
Red
G/Y
SC
RC
N
Green / Yellow
Starting coil
Running coil
Normal
Ground
8

Warning! Do not use side brush in a room with no
wall skirting, otherwise, the wall will get dirty.
Accessories
Transporter Side Brush
Upkeep of your PORT A SCRUB
·Supply cord
Regularly inspect sheath, plug and cord anchorage for
damage or loose connection.
·Brushes
For maximum life wash the brushes regularly. Ensure
machine is in Transport mode when not in use. Store
additional brushes in a vertical position to avoid bending
of bristles. Check for permanent bending of bristles in a
particular direction. This may occur if the machine is
operated for several days without removing the brushes,
which is not recommended. If this occurs, reverse the
brush so that the bent bristles are automatically
straightened.
Warning! Empty all liquid from the machine
before using the transporter.
The simply fitted trolley
p r o v i d e s f o r e a s e o f
movement when transporting
the machine.
Installing the Transporter
1. With the machine handle in the upright position place the
transporter centrally alongside the machine.
2. By holding the machine firmly, strap the velcro with the
machine to fix the transporter.
3. Ensure that the velcro strap properly wrapped around the
bottom handle.
4. Now the transporter is ready to use. The machine can
then be maneuvered easily whilst holding the top handle.
1. Remove the front brush and brush shaft.
2. Fix the shield assembly and screw it into the
side plate and tighten.
3. Insert the side brush through the shield and
main brush.
1. Tilt the machine at an angle move forward. This
way, the dirty water thrown by the side brush will be
collected by the rear brush.
2. Use side brush only for washing the edges.
·Wiper Blade
This may wear out after years of use. If this occurs the
water collection performance will decrease. It should
be replaced by an authorized Service Agent.
·Solution feed filter
The filter prevents clogging of the spray nozzle and
should be periodically cleaned. Use pressurized air/
water for cleaning.
·Nozzle maintenance
If the spray of the nozzle become blocked, slide the
nozzle cover off and remove nozzle wash in clean
water and clean using a pin and refit.
To get the maximum life of the machine ensure the following.
To wash the edges, the
side brush shall be used.
Switch off and unplug the
machine before fitting the
side brush.
Fitting the side brush
Using the side brush
ADDITIONAL INFORMATION-WEEE
( WASTE OF ELECTRIC AND ELECTRONIC EQUIPMENT )
The symbol on the product or its packages indicates that the product may not be treated as house hold waste. Instead it shall be
handed over to applicable collection point for recycling of electrical and electronic equipment. By ensuring this product is disposed
of correctly, you will help prevent potential negative consequence of the environment and human health, which could otherwise be
caused by inappropriate waste handling of this product, please contact your local city office, your household waste disposal
service or shop where you purchased the product.
9

HOUSING - DRIVE SIDE
311
V12
V7
V10
32 19 111
2
77
46
105
93
62
212
10
25
24
116
116a
11
115b
19
395
20
396 80
114
10
19
19
728
115a
115b
11
19
1
43
59
42
V8
10
34
92
115 63
260
9

HOUSING-DRIVE SIDE
11
SL.NO PART NO DESCRIPTION QTY
1 814103 SLOTTED CSK SCREW SS 304 M4 X 10 4
2 818001 CR PAN HEAD SCREW - SS304 - M3X6 6
7 829321 HEX SOC CSK HEAD SCREW - SS304 -M6X14 3
9 832303 HEX SOC HEAD CAP SCREW-SS304-M6X10 2
10 832305 HEX SOC HEAD CAP SCREW-SS304-M6X15 7
11 832307 HEX SOC HEAD CAP SCREW-SS304-M6X20 2
19 875010 DG BALL BEARING 6003 2RS 9
20 3250493 BUSH GUIDE MOTOR SHAFT 1
24 925001 BELT-500 5M 1
25 925002 BELT 425 5M 1
28 925012 WASHER-BRIDGE 2
32 925018 BUMPER-FRONT 1
34 925026 BUMPER-COVER 1
42 925047 SLIDER-BRUSH 1
43 925048 HOUSING-SLIDER 1
46 925054 LIP SEAL 17 2
59 925092 PIN-SLIDER 1
62 925099 O RING-WHEEL 2
63 925102 SHIELD-LEVER BOTTOM 1
77 925130 CAP-BEARING 2
80 925227 HOUSING-GEAR SUPPORT 1
92 925219 SHIELD-LEVER-TOP 2
93 925220 IDLER-DRUM 2
105 925249 SLEEVE-BUMPER 3
111 925804 SPROCKET ASSY-BRUSH 2
114 925074 SPROCKET-GEAR 2
115 925815 IDLER ASSY-TOOTHED 1
115a 925075 SPROCKET-IDLER 1
115b 925046 HUB-IDLER 2
116 925816 IDLER ASSY-PLAIN 1
116a 925061 SLEEVE-IDLER 1
212 925221 STUB AXLE (29) 1
260 925579 DRUM PINION ASSY 1
311 925530 HOUSING ASSY-GEAR SUPPORT 1
395 3250567 GEAR LH - NEW 1
396 3250568 GEAR RH - NEW 1
V7 925802 HOUSING ASSY-DRIVE 1
V8 925319 COVER HOUSING-MM 1
V10 928552 HOUSING ASSY-DS-COMPLETE-MM 1
V12 928554 COVER ASSY COMPLETE-DS-MM 1

HOUSING - IDLE SIDE
12
62
212
93
33
188
68
17
106
15
242
18 9
19
79
2
77
46
32
105
9
10
V8
34
58
59
43
1
92
63
81
16
100
39
V11
V13
V5
346
95
96
98
99
V3
133
75
94b
94a
94
129
86
131
132
89
72
73
252
6
175
21
246
246
248
95
96
98
99
V2
10
V3
133
75
94b
94a
94
129
86
131
132
89
72
73
90
6
175
21
246
246
326

HOUSING - IDLE SIDE
13
SL.NO PART NO DESCRIPTION QTY
1 814103 SLOTTED CSK SCREW SS 304 M4 X 10 4
2 818001 CR PAN HEAD SCREW - SS304 - M3X6 6
6 829208 HEX SOC CSK HEAD SCREW - SS304 -M5X25 2
9 832303 HEX SOC HEAD CAP SCREW-SS304-M6X10 2
10 832305 HEX SOC HEAD CAP SCREW-SS304-M6X15 5
15 845061 WASHER-SS304-6.4X12.5X1.6 1
16 845081 WASHER-SS304-8.4X17X1.6 1
17 863060 SPRING WASHER - STEEL - M6 1
18 866060 EXTERNAL TOOTHED LOCK WASHER - M6 1
19 875010 DG BALL BEARING 6003 2RS 2
21 881023 WIRE TIE - 75MM 3
32 925018 BUMPER-FRONT 1
33 925019 BUSH-BRUSH SHAFT 2
34 925026 BUMPER-COVER 1
39 925040 STUB AXLE 1
43 925048 HOUSING-SLIDER 1
46 925054 LIP SEAL 17 2
58 925083 SLIDER-TRANSPORT 1
59 925092 PIN-SLIDER 1
62 925099 O RING-WHEEL 2
63 925102 SHIELD-LEVER BOTTOM 1
68 925109 COVER-FAN 1
72 925116 GROMMET 1
75 925124 CAP-CIRCUIT BREAKER 1
77 925130 CAP-BEARING 2
79 925147 STOPPER-LEVER 1
81 925500 PEDAL 1
86 925192 NUT-INSULATION 2
89 925199 CONNECTOR-2.5 SQ.MM 1
90 (110) 2530009 SWITCH 21A 2
90 (230) 925200 SWITCH 2
92 925219 SHIELD-LEVER-TOP 1
93 925220 IDLER-DRUM 2
94 925529 SOCKET ASSY 1
94a 925092 PIN-SLIDER 1
94b 928025 TERMINAL-SOCKET 3
95 925501 CONNECTOR ASSY-BLUE-SOP-SWA 1
96 925502 CONNECTOR ASSY-BROWN-CBA-COP-COP 1
98 925504 CONNECTOR ASSY-BROWN-SOP-SWA 1
99 925505 CONNECTOR ASSY-G/Y-SOP-RING 1
100 928017 SPRING-PEDAL 1
105 925249 SLEEVE-BUMPER 3
106 814102 SLOTTED CSK SCREW SS 304 M4X8 1
928086 LEVER-SWITCH-ACT 1
3250592 LEVER-SWITCH-ACT - 110V 1
129

HOUSING - IDLE SIDE
14
62
212
93
33
188
68
17
106
15
242
18 9
19
79
2
77
46
32
105
9
10
V8
34
58
59
43
1
92
63
81
16
100
39
V11
V13
V5
346
95
96
98
99
V3
133
75
94b
94a
94
129
86
131
132
89
72
73
252
6
175
21
246
246
248
95
96
98
99
V2
10
V3
133
75
94b
94a
94
129
86
131
132
89
72
73
90
6
175
21
246
246
326

HOUSING - IDLE SIDE
15
SL.NO PART NO DESCRIPTION QTY
131 928090 INSULATION-TOP 1
132 928091 INSULATION-BOTTOM 1
133 928107 NUT-CIRCUIT BREAKER 1
175 925506 CONNECTOR ASSY-34P 1
188 925207 SLEEVE-TIE ROD 3
212 925221 STUB AXLE (29) 1
242 925347 CLAMP- WIRE (NEW HOUSING) 1
246 2530005 GROMMET (2 CABLE) 2
248 (110) 2580033 CABLE CONNECTOR ASSY 1
326 (230) 925532 ELECTRICAL ASSY-13 MFD-34P 1
346 (110) 2580011 ELECTRICAL ASSY-34P-110V 1
V2 (230) 925534 CAPACITOR 13MFD 1
V3 (110) 925173 CIRCUIT BREAKER - 10A 1
V3 (230) 925166 CIRCUIT BREAKER - 3.5A 1
V5 925807 HOUSING ASSY-IDLE 1
V8 925319 COVER-HOUSING-MM 1
V11 928558 HOUSING ASSY-IS-COMPLETE-MM 1
V13 928555 COVER ASSY COMPLETE-IS-MM 1

PUMP HOUSING
170
102
303
123
123a
122b
16
M12110
244 V2
246
271
346
165
187
184
1185
180
159
181
164
245
168
155
101
176 V9
169
382
186
182
163
167
177
158
154
174
173
162
165
270
326

PUMP HOUSING
17
SL.NO PART NO DESCRIPTION QTY
1 814103 SLOTTED CSK SCREW SS 304 M4 X 10 3
101 928049 O-RING-PUMP 1
102 928776 FILTER ASSY 1
122b 925162 PAD-LID 2
123 925836 LID ASSY-DIRTY WATER TANK 1
123a 925132 LID-DIRTY WATER TANK 1
154 928064 HOSE-VALVE (275MM) 1
155 928065 INSULATION-SWITCH 1
158 928097 CLIP-HOSE 1
159 928754 NOZZLE ASSY-STD 1
162 928767 BOOT-NOZZLE 1
163 818009 CR PAN HEAD SCREW - SS304 - M3X 30 2
164 823030 HEX NUT - SS 304 - M3 2
165 823040 HEX NUT - SS 304 - M4 7
167 925187 LIMIT SWITCH 2
168 925204 STRIP-LID 2
169 925224 EXTENSION BASE SWITCH 1
170 925233 HOSE-VALVE-165 2
173 925261 CONNECTOR- HOSE-34P 1
174 928076 BOOT- HOSE 1
176 925511 ADAPTOR NOZZLE 1
177 925573 CONNECTOR ASSY-PUMP HOUSING 1
180 928016 SEAL-NOZZLE 1
181 928019 BASE-SWITCH 1
182 928022 LEVER 1
184 3360101 SUPPORT RING PUMP 2
185 8250950 PUMP HOUSING W/LABEL - 34MM 1
186 928044 LID-FRESH WATER-PUMP 1
187 928048 SPACER-NOZZLE 1
245 814104 SLOTTED CSK SCREW-SS304-M4X12 4
270 845039 WASHER-SS304- 4.0X8.0X0.5 4
303 928541 TANK ASSY COMPLETE DIRTY WATER 34 1
326 8251239 PUMP HOUSING COMPLETE - 12230 - MM
382 925577 BASE SWITCH ASSY 1
V9 928054 VIBRATING PUMP (230V-50HZ) 1
183 928023 CLAMP-PUMP 1
244 2530004 CLAMP-CAPACITOR 1
271 814313 SLOTTED CSK SCREW-SS304-M4X15 4
346 8250949 PUMP HOUSING COMPLETE - 3116 - MM 1
V2 2530006 CAPACITOR-63.5 MFD STANDARD 1
V9 925325 VIBRATING PUMP-EP8S-120V-60HZ 1
For M12110

LEVER & GUIDE LINK MECHANISM
119a
118a
119
64
118
76
26
383
4
128
120
120a
119a 82
119
29
78
41
47
76
91
26
76
113
45
18
SL.NO PART NO DESCRIPTION QTY
4 818104 CR PAN HEAD SCREW - SS304 - M4X12 2
26 925008 CLEVIS PIN-WHEEL 5
29 925014 CLEVIS PIN-LEVER 1
41 925043 LINK 1
45 925053 SHIELD-WHEEL 8
47 925055 LEVER-BRUSH ACTUATION 2
64 925105 BUTTON LEVER 4
76 925129 CIRCLIP - E6.0 6
78 925139 GUIDE-LINK 1
82 925180 SPRING-LEVER 1
91 925212 SPACER-LEVER 1
113 925810 WHEEL 4
118 925822 LEVER ASSY-DRIVEN 1
118a 925085 LEVER-DRIVEN 1
119 925823 LEVER ASSY-IDLER 2
119a 925086 LEVER-IDLER 2
120 925824 LEVER ASSY-DRIVER 1
120a 925087 LEVER-DRIVER 1
128 928085 LEVER SWITCH 1
383 925829 GUIDE-LINK-ASSY 1

HANDLE ASSEMBLY
12
71
11
V4
23
153
179
161
152
364
288
126
135
12
160
104
48
4
293
189
60
35
57
3
328
117
225
73
65
4
52
228
66
224
226
294
318
224
225
227
72
295
73
229
317
19

HANDLE ASSEMBLY
20
SL.NO PART NO DESCRIPTION QTY
3 818102 CR PAN HEAD SCREW - SS304 - M4 X 8 1
4 818104 CR PAN HEAD SCREW - SS304 - M4X12 10
11 832307 HEX SOC HEAD CAP SCREW-SS304-M6X20 2
12 844063 WASHER-STEEL-6.4 X 18 X 2.0 4
23 922289 RETAINER-ELECTRIC CABLE 1
35 925028 CLAMP-CABLE STOPPER 1
48 925057 CAP-HANDLE-TOP 1
52 925069 BASE-CABLE HOLDER 2
57 925082 CLAMP-CABLE ADJUSTMENT ASSY 1
60 925096 LOCK NUT-CABLE ASSY 1
65 925106 SPRING-CABLE HOLDER 6
66 925107 WASHER-CABLE HOLDER 6
71 925115 PLUG-HANDLE 2
73 925120 B3.5X9.5 SELF TAPPING SCREW 10
104 928506 PULL CABLE ASSY-P 1
117 925818 HANDLE ASSY-TOP 1
126 928766 KNOB ASSY 2
135 928778 HANDLE-BOTTOM 1
152 928050 GASKET-VALVE 1
153 928061 TANK-4L 1
160 928764 BASE-VALVE-ASSY-W34T 1
161 928765 VALVE-ASSY 1
179 928007 NUT-VALVE-W34T 1
189 925274 SLEEVE - CABLE ASSY - AX 1
224 925305 KNOB-CABLE-HOLDER-II 2
225 925306 KNOB-CABLE- HOLDER-I 2
226 925307 KNOB-TANK HOLDER-LH 1
227 925308 KNOB-TANK HOLDER-RH 1
228 925339 BASE CABLE AND TANK HOLDER 2
229 925340 GUIDE CABLE (ST CABLE) 2
288 836206 CRPH SELF TAPPING SCREW-SS 304- 3.5X16.0 2
293 925049 PULL HANDLE 1
294 928633 PIPE HANDLE ASSY -LH-STD 1
295 928634 PIPE HANDLE ASSY-RH -STD 1
317 928636 PIPE ASSY RH- T/P 1
318 928635 PIPE ASSY LH-T/P 1
328 925522 TOP HANDLE W/PULL CABLE ASSY-34P 1
364 928855 TANK-4L-ASSY 1
384 925116 GROMMET 1
V4 925920 POWER CORD - EURO 1
V4 925922 POWER CORD - CANADA 1
V4 925923 POWER CORD - UK 1
V4 2590015 POWER CORD - ST - YELLOW (RAL 1018) 1