Minuteman V10 Pro Plus User manual

Minuteman ®
Excellence Meets Clean
User Manual and Parts Guide
0~
Back Pack

Before Using
This manual is furnished with each new V1 0 Pro and V1 0 Pro Plus. This provides the necessary operating and preventative maintenance
instructions. Operators must read and understand this manual before operating or servicing this machine.
This machine was designed to give you excellent performance and efficiency. For best results and minimal cost please follow the general
guidelines below:
• Operate the machine with reasonable care.
• Follow the manufacturer's suggested maintenance instructions as provided
in this manual.
• Use original manufacturer's supplied parts.
19.5"
(
495 mm)
2

Filtration Efficiency Chart V1 0115P
Test dust consists of particles between 0-8 mi c ron as per Standard EN 60312.
Individual Filter
Efficiency System Filtration
Efficiency
Model:
Model No.:
Current max.
Maximum motor power
Worki
ng width
Weight (exc. Electrical cord and floor tools)
Noise level average (at 3ft from surface)
VoltageiFrequency
Thermal Control (Manual Reset)
Air Flow (at nozzle)
Dust Bag
Filtration
Cord
Protection
Suction
Technical Specifications
V10 Pro V10 Pro Plus
V10115P V10115PP
V10115P V10115PP
10 Amps 10 Amps
1300W
1300 w
10.75" (275mm) 10.75" (275mm)
9.0 lb
(4.1 kg) 9.3 lb (4.2 kg)
71 dBA 69 dBA
11 0-120 V I 50-60 Hz 110-120
VI 50-60Hz
230F/110C 230F/110C
65 cfm (30 lis) 65 cfm (30
1/s)
305 cu.in (5 I)
245 cu in (4 I)
Refer chart 99.97% @
0.3~m
50ft (15m)
50ft (15m)
3-wire ground 3-wire ground
80"
of water (-20 kPa) 80"
of water (-20 kPa)
3

4

Before Using Page 2
Technical Specifications Page 3
Safety Instructions
Page 6
Instructions de securite
Page 7
Unpacking Instructions and Warnings
Page 8
Deballage des Instructions et Avertissements
Page 9
Machine Overview and Assembly Page 10
Machine Overview Page 11
Machine Overview, Wearing and Adjustment
Page 12
Safety and Maintenance Checks
Page 13
Operating and Working
Page 14
Parts Guide and Exploded Diagram Page 15
Electrical Circu it and Warnings
Page 16
Trouble Shooting Page 17
Warranty Page 18
Contact Details Back Page
5

Safety Instructions
THIS APPLIANCE IS INTENDED FOR COMMERCIAL USE ONLY
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should always be followed,
Including the following:
READ ALL INSTRUCTIONS
BEFORE USING THE BACK PACK VACUUM CLEANER
• Do not leave the appliance when plugged in. Unplug from the power point when not in use and before servicing.
•
Do not use outdoors or on wet surfaces.
•
Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• Use only as described
in this manual. Use only manufacturer's recommended attachments.
•
Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water,
return it to a service centre.
•
Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over
cord. Keep cord away from heated surfaces.
•
Do not unplug by pulling on co r d. To unplug, grasp the plug, not the cord.
•
Do not handle plug or appliance with wet hands.
•
Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.
• Keep hair, loose clothing, fingers and all parts of body away from openings and moving parts.
• Turn off all controls before unplugging.
• Use extra care when cleaning
on stairs.
•
Do not use to pick up flammable or combustible liquids, such as gasoline, or use in areas where they may be present.
• Connect to a properly grounded outlet only. See Grounding Instructions.
•
Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
•
Do not use without dust bag and/or filters in place.
WARNING!
• No liability can be accepted for damages to persons and or objects caused by improper use, maintenance carried out by unauthorised personnel, use of unauthorised
and non original spare parts, any form
of tampering and or modifications to the original product.
• The manufacturer reserves the right to modify the appliance and or the accessories supplies without prior notice.
SAVE THESE INSTRUCTIONS 6

POUR USAGE COMMERCIAL SEULEMENT
MODE D'EMPLOI SECURITAIRE
Lorsque l'on utilse un appareil electrique, des precautions
de base doivent tourjours etre suivies telles que:
IMPORTANTES MESURES DE SECURITE
Toute personne amenee a utiliser ou entretenir cette machine est tenue, auparavant, de lire toutes les instructions et recommandations de ce guide, et de s'assurer de les avoir toutes
comprises.
L'utilisation de cette machine a proximite de produits inflammables
ou explosifs est formellement interdite.
Cette machine a ete
con<;:ue pour aspirer les poussieres et saletes uniquement en interieur.
Minuteman deconseille fortement toute autre utilisation de
sa machine.
Les conditions mentionnees ci-dessous presentent
un danger pour l'operateur et l'appareil. Lisez attentivement ce guide pour reagir de Ia meilleure far;:on possible si l'une de ces condi-
tions vient a se produire. Reperez tous les dispositifs de securite equipant
Ia machine et prevoyez des sessions de formation pour tous ceux pouvant etre amenes a utiliser Ia machine.
Signalez immediatement tout dommage
ou fonctionnement anormal. N'utilisez pas Ia machine si elle n'est pas en parfaite condition de marche.
IMPORTANTES MESURES DE SECURITE
L'utilisation d'un appareil electrique demande certaines precautions:
LIRE TOUTES LES INSTRUCTIONS AVANT
DE FAIRE FONCTIONNER (CET APPAREIL)
AvERT Iss EM EN T. Pour reduire les risques d'incendie, de choc electrique ou de blessure :
1.
Ne pas laisser l'appareil sans surveillance lorsqu' il est branche. Debrancher lorsque l'appareil n'est pas utilise et avant l'entretien.
2. Ne pas utiliser a l'exterieur et
ne pas aspirer de matieres humides.
3. Ne pas permettre aux enfants de jouer avec l'appareil. Une attention particuliere est necessaire lorsque l'appareil est utilise par des enfants ou a proximite de ces derniers.
4. N'utiliser que conformement a cette notice avec les accessoires recommandes par le fabricant.
5. Ne pas utiliser si le cordon ou Ia fiche est endommage. Retourner l'appareil a un atelier de reparation s' il ne fonctionne pas bien, s' il est tombe ou s'il a ete endommage, oublie a l'ex-
terieur
ou immerge.
6. Ne pas tirer soulever ni trainer l'appareil par le cordon. Ne pas utiliser le cordon comme une poignee, le coincer dans I' embrasure d'une porte ou l'appuyer contre des aretes vives ou
des coins. Ne pas faire rouler l'appareil sur le cordon. Garder le cordona l'ecart des surfaces chaudes.
7. Ne pas debrancher
en tirant sur le cordon. Tirer plutot Ia fiche.
8. Ne pas toucher Ia fiche ni l'appareillorsque vos mains sont humides.
9. N'inserer aucun objet dans les ouvertures. Ne pas utiliser l'appareillorsqu'une ouverture est bloquee. S'assurer que de Ia poussiere, de Ia peluche, des cheveux ou d'autres matieres
ne reduisent pas le debit d'air.
10 . Maintenir les cheveux, les vetements amples, les doigts et toutes les parties du corps a l'ecart des ouvertures et des pieces mobiles.
11 . Mettre toutes les commandes a Ia position ARRET avant de debrancher l'appareil.
12. User de prudence lors du nettoyage des escaliers.
13 . Ne pas aspirer des liquides inflammables ou combustibles, comme de I' essence, et ne pas faire fonctionner dans des endroits ou peuvent se trouver de tels liquides.
14. Ne rien ramasser de ce qui brule our de fumee tells que cigarettes, allumettes
ou cendres en feu.
15. Ne pas employer sans filter de poussiere
ou autre en position.
16. Brancher dans une prise avec une prise de terre seulement. Voir references pur prise de terre.
CONSERVER CES INSTRUCTIONS 7

Unpacking Instructions and Warnings
Inspection
Carefully unpack and inspect your V1 0 Pro and V1 0 Pro Plus for shipping damage. Follow any unpacking instructions on shipping pallet. Each unit has
been tested and thoroughly inspected before shipment. Any damage is the responsibility
of the delivery carrier who should be notified immediately.
Operator Responsibility
Read this manual carefully before operating this machine.
The operator
is responsible for taking care of the daily maintenance and inspection of the machine to keep it in good working condition. The operator must
inform the service mechanic or supervisor when the scheduled maintenance intervals are required as stated in the MAINTENANCE section of this manual.
Grounding Instructions
This product must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk
of electric shock. This product is equipped with a cord havi ng an equipment grounding conductor and a grounding plug. The pl ug must be plugged into an
appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
Warning
Improper connecti on of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified
electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug
provided with the
product- if it will not fit the outlet, have a proper outlet installed by a qualified electrician.
This product
is for use on a nominal 120-volt circuit and has a grounding plug that looks like the plug illustrated at the
right. Make sure that the product
is connected to an outlet having the same configuration as the plug. No adapter should
be used with this product.
Warning
Grounding methods
GROU NDEDm_l
O UT L ET a
rizJ GROUNDED
OUTLET BOX
This appliance is equipped with a thermal resetting protection device. This is a safety feature to protect the appliance from overheating. If the appliance
should suddenly stop and will not start, turn off the main switch and pull the plug offthe socket outlet. Do not operate the appliance for at least 30 minutes.
8

Deballage des Instructions etAvertissements
Inspection
Deballer soigneusement et inspecter Ia possibilite de tout dommage apparent. Chaque machine est completement inspectee a l'usine et les dommages
de transit sont
Ia responsibilite de Ia compagnie de transport que devrait etre prevenue immediatement.
Instructions pour prisse de terre
Cet appariel doit posseder une prise de terre, S'il y avait malfunction ou brisure, une prise de terre offre une voie de moindre resistance de facon ace que
le courant electrique reduise le risque de choc. Cet appareil est equippe d'une prise de terre de meme qu'une prise de courant avec prise de terre. Cette
prise doit etre deposee dans une sortie adequate qui sera installee selon les exigeances et les lois locales.
Danger
Un mauvais assemblage du conducteur de prise de terre pourrait causer un risque de choc electrique. Verifier aupres d'un electrician certifie ou d'une per-
sonne qualifiee
si vous avez des doutes asavoir si Ia prise est bien completee Ne pas modifier Ia prise qui vient avec cet appariel. Si Ia prise n'accede
pas a
Ia sortie, un electrician qualifie devrait Ia remplacer.
Cet appareil doit etre utilise sur
un circuit de nominal de 115/120 volt et posseder une prise de terre que ressemble a Ia prise illustree dans le schema A.
Bien vous asssurer que Ia sortie de courant soit de Ia meme configuration que Ia prise. Aucun adapteur ne doit etre utilise avec cet appareil.
Avertissement
Methode de Ia terre
La terre
sortie
Fourchone de prise
(A)
de mise a terre
Boite de
Ia
terre
Cet appareil est equipe d'un systeme de protection de reglage thermal. II s'agit d'un dispositif pour preserver l'appareil de Ia surchauffe. Si l'appareil s'ar-
rete subitement et
ne redemarre pas, eteignez l'interrupteur principal et debranchez Ia prise. Attendez au mains 30 minutes avant de le reutiliser.
9

Machine Overview and Assembly
Machine Overview and Assembly
A. Lid
B. Hose Release Button
C. Inlet Elbow
D. Back Pad
E. Shoulder Pads
F. Shoulder Buckle
G. Shoulder Strap Guides
H. Inlet Cord and Socket
I. Cord Restraint
J. Waist Pad
K. Tool Holders
L. Belt Adjuster
M. Side Release Buckle
N. On/Off Remote Switch
0. Cable Restrainer
P. Magnetic Latch
Q . Frame Carry Handle
R. Hose Inlet
S. Bent End Piece
T. Air Regulator (BEP)
U. Wand (2 Piece)
V. Ezi-glide Floor Tool
W. Crevice Tool
p
Assembly Instructions
1. Connect 2 piece Wand (U)
2. Connect Wand (U) to Bent End Piece (S)
3. Connect Inlet Elbow (C) to Lid (A)
4. Switch on at on/off button (N)
10

Hose- To Remove
Press Hose Release Button, and gently pull
Inlet Elbow from Lid.
Hose- To Fit
Insert Inlet Elbow into lid opening.
Lid- To Remove
Lift Magnetic Latch opposite side of inlet,
rotate Lid away from canister body.
Lid- To Fit
Rotate onto canister body fitting inlet side first,
ensuring accurate alignment. Magnetic latch
will engage automatically.
NOTE: The lid can be fitted for either left or
right operation.
Cloth Filter Bag- To Remove
Lift from top of canister using bag rim.
Filter Bag- To Fit
Place over canister rim and press firmly ensuring
bag is level.
Machine Overview
VFD Filter- To Remove
Use the Panel Filter flaps to lift from canister base.
Remove with care from the canister.
VFD Filter- To Fit
Insert into canister base filter recess. Press firmly
around the edge of the filter to fit into position.
NOTE: Do not press on filter media.
HEPA Filter -To Remove
(V1 0 Pro-Plus Models only)
Loosen Wing Nut on top filter cartridge and remove
from canister vertically.
HEPA Filter -To Fit
Locate into Canister Base filter recess, tighten Wing
Nut until firm.
Paper Bag Filter- Removal & Disposal
Ease cardboard retainer off the groove on the
Inlet Spout. Fold card board tab over bag inlet
hole to prevent spillage. Dispose into garbage
bin.
NOTE: The paper bag is manufactured using
bio-degradable material.
Paper Bag- To Fit
~
/~w7 RB ~ );
portion of cardboard (A) into Inlet Spout groove. 1 /)
Ease the remaining serrated portion of cardboard (B) (\ ·. / /
onto groove. Keep corners of paper folded down to \ · __ J_-:-- -..;;j'
avoid entrapment under lid edge. A \...) j
Align paper bag cardboard, engage non-serrated
11

Machina Overview, Wearing and Adjustment
ON/OFF Switch- To Operate
The switch is located on the left hand side
of the
Waist Pad. Operation
is 0/1 for OFF/ON.
Cord- To Fit
For safety in reducing tripping hazards and for
unplugging, fit the cord into integral cord
restraint as shown.
Air Regulator- To Adjust
Slide forward to close, this provides more air at
the nozzle. Slide back for less air,
th is is to be
used when vacuuming loose materials
eg. curtains.
Attachments- To Fit or Remove.
Tw ist and pull to disassemble. Attach at any
point from Bent End Piece to Wand end, to suit
application.
Tool Holder- To Adjust
Size the adjustment loop before wearing to suit
the tool to be inserted.
Wearing and Adjustment
Adjusting shoulder and waist pads
Shoulder Pad -to loosen Pull away from the
Shoulder Pad, this releases the Strap from the
Buckle.
Waist Pad - Preliminary Adjustment
• Feed free end of Strap 1 through belt
adjuster 2 to release.
• Feed strap 1 through Buckle 3 to release.
• Adjust Strap 1, Buckle 3, Belt Adjuster 2, to
fit approx 1/2 girth of user.
• Belt
Ad juster 5 gathers loose end of Strap 4.
• Pu ll free end of Strap 4 for final adjustment.
Final Fitting
• Loosen Shoulder Pad and Waist Pad. Lift
machine onto one shoulder by the shoulder
~
strap. Insert opposite arm through the
shoulder strap by which the machine
is
lifted. Sl ide other arm though the remaining
strap.
• Positi
on the Waist Pad into the 'small' of
your back.
• Clip buckle together and tighten Waist Pad
un t il secure and comfortable.
• Pull down
on both ends of the shoulder strap
until the Back Pad contacts the back.
12

Cloth Bag Filter
Regularly
Remove Cloth Filter Bag and empty.
Occasionally
Turn bag inside out and remove fine dust
coating using a soft
banister brush or vacuum.
Note: The filter material has been treated
with a moisture repelling agent for
improved dust release. There is
no
requirement for washing or dry cleaning the
Filter Bag.
VFD Filter
Regularly
Remove VFD Filter and tap out dust.
Occasionally
Brush surface using a soft nylon brush or
wash filter
in neutral cleaner solution then
rinse
in clean water.
Note: Ensure filter is completely dry before
recommencing vacuuming.
rooU'oor
Safety and Maintenance Checks
HEPA Filter (where fitted)
Regularly
Remove HEPA filter and tap out dust.
Occasionally
Wash in neutral cleaner solution using swirling
action only, then rinse in clean water.
Note: The filter material has been treated with
a soft polymer moisture repelling agent, do not
touch media surface by hand or any other
mechanical device. This can damage the media
and impair the filtration quality. Ensure filter
is
completely dry before recommencing
vacuuming.
As Needed
Check Inlet Elbow, Hose, Bent End Piece and
Floor Tool for blockages.
Regularly
Check cord for cuts, exposed wire, abrasion
and knuckling.
Replace cord only with original manufacturer's
part.
Note:
Always unplug cord from power point when not
in use.
Gather the cord by winding from the machine
end.
Drape cord over handle for storage.
13

Operation and Working
Using
• Fo r comfortable operation, stand upright with a relaxed
posture, arms hanging loosely to the side.
• Maintaining a straight wrist, hold the hand grip section of
the wand with one hand,
pa ra ll el to the floor.
• When vacuuming under office desks, the reach
of the
wand
is sufficient to avoid bending at the wais t.
• When vacuuming under lower profile objects or when
picking up items off the floor, bend the knees and
maintain a straight back.
• When turning, do not twist at the waist.
Turn using your feet.
Working
• Plan the work path based on location of the power
point, room/furniture layout, and entrance and exit
points.
• Commence vacuumi
ng using a systematic approach
working one half
of the area first, away from the power
point, and then the other half of the area, returning
back to the start.
• Ensure that the power cord
is clear of feet to reduce
likelihood
of tripping.
ODD
14

No. Part Name Part No.
1 Lid Assy V10 13717001
2 Elbow Inlet 13640001
3 Hose BEP Assy
032
13677002
4 Hose
032 x 1.2m Blk 13670006
4a Ring Click Blk 13770003
4b Fitting Screwed Hose HUL
032
13650002
5 Elbow BEP
032 Blk 13640002
6 Wand
032 x 550mm Cr. Steel 13820011
7 Tool Flo
or Ezi-Giide 13797001
8 Tool Crevice
032 Blk 13790001
9 Filter HEPA& FastenerAssy 13657004
10 Label Maintenance USA 13710010
11 Pad Back Blk 13750003
12 Buckle Adjuster 38 13610006
13 Pad Shoulder Blk L & R Set 13750004
14 Buckle Side Release 38 13610005
15 Buckle Shoulder LL 38 13610007
16 Pad Waist Blk 13750005
17 Screw WN1412 KB50 x 16 ZP 13780003
18 Frame RVXP-
V1 0 13650001
19 Cord USA 15m V10 12-04 13620008
20 Insulation End Cap (set) 13680003
21 Clamp Motor 13620005
22 Motor Vacuum Harbin 120V 13727001
23 Baffle Motor Housing 13610004
24 Seal Motor Harbin 13780006
25 Screw WN1412 KB40 x 12 ZP 13780002
26 Base Upper Canister 13610003
No. Part Name
27 Seal Canister Housing
28 Label Pro
28a Label Pro Plus
29 Housing Upper Canister Assy
30 Filter VFO Assy
31 Filter Bag Assy 5L (standard}
31a Filter Bag Assy
4L (HEPA)
32 Filter Paper Bag 5/Pkt (Standard}
32a Filter Paper Bag 5/Pkt (HEPA)
33 Socket Inlet C14
34 Wire E V10
35 Insulation Motor Housing End
36 Housing Lower Canister
In & Remote
37 Cap Motor Housing
V1 0
38 Insulation Motor Housing Side (set)
39 Grommet Strain Relief
V1 0
40 Nut Hex
M3ZP
41 Housing Remote Switch V1 0
42 Switch Rocker 2HP
43 Washer Flat M3 ZP
44 Screw M3x25 Pan Hd. ZP
45 Cord Remote Switch
V1 0
46 Cord Grip
V1 0
47 Clamp P
08
48 Washer 410 x 9. 500 ZP
49 Washer M3 Ex t. Shakeproof
50 Screw No.6 x 10 Mush. Hd ZP
Part No.
13780004
13710007
13710008
13677001
13657003
13657001
13657002
13657006
13657007
13780007
13820001
13680001
13670002
13620003
13680002
13660001
13730001
13670005
13780014
13820009
13780001
13620006
13620007
13620012
13820012
13820010
13780016
Parts Guide and Exploded Diagram
--- --------,
I
I
I
I
I
I
I
~ , ,' i
~\ i
~ --- ~ :
~ I
§~ .· :
~ I
~' I
(x 4) o I
~--- ----- _ _____ ]
15

Electrical Circuit and Warnings
Electrical Circuit
Warnings
Do Not
DOUB LE POL E
SINGLE T HROW
SW I TCH
WH I TE (NEUTRAL)
BLACK
• Do not vacuum wet surfaces, damp areas or suck up water.
VACUUM MOTOR
• Do not use machine ifwater has been picked up by the vacuum system without an
electrical inspection by a qualified person.
• Do not vacuum anything that is burning or smoking such as cigarettes, matches
or hot
ashes.
• Do not use the machine
in areas where flammable or combustible liquids, vapors or gas
are present.
• Do not operate near explosive materials such as solvents, thinners, fuels or grain dust.
POWER
INLET
)--CZJ
3 3
Ground Green ,
Green/Ye llow
16

Always switch off machine and unplug prior to correcting any problems. If you are unable to rectify the problem, contact your service agent.
Problem: Machine not working
Cause No power at power point.
Solution Connect machine to a functional power point.
Cause Power cord not plugged into power point or machine.
Solution Check plug is firmly plugged into power supply and machine.
Cause Machine or power supply not switched on.
Solution Turn on/off switch to ON (1) . Turn power supply outlet on.
Cause Machine has switched off due to overheating.
Solution Switch off and unplug machine. Check for any blockages
in wand, floor tool and inlets. Ensure filters and paper and cloth bags are clean.
Wait for
30 minutes and switch machine back on. If machine does not start up, contact service agent.
Problem: Poor or No Suction
Cause
Solution
Cause
Solution
Cause
Solution
Cause
Solution
Cause
Solution
Blockage.
Turn off machine and unplug. Check wand, suction hose, floor tool, elbow inlets for obstructions and remove.
Paper or Cloth Filter Bags are full.
Check paper bag and iffull, remove and replace. Check Cloth Filter Bag, turn inside out and brush with a soft banister brush before
replacing.
Hose not installed properly or damaged.
Check hose connection and ensure it is locked in. Replace if damaged.
VFD Filter is blocked.
Remove VFD Filter and tap gently to remove excess dust before replacing.
Air Regulator needs adjustment.
Close Air Regulator on hose to obtain suction required.
Problem: Backpack is Uncomfortable to Wear
Cause Backpack is not fitted correctly to your body.
Solution Adjust waist bands and shoulder straps as described on page 12 to ensure correct fit.
Cause Pads or straps are worn.
Solution Replace padding/straps.
17

Minuteman International Made Simple Commercial Limited Warranty
REVISION F EFFECTIVE 6/1/2009
Minuteman International, Inc. warrants to the original purchaser/user that the product is free from defects in workmanship and materials
under normal use. Minuteman will, at its option, repair
or replace without charge, parts that fail under normal use and service when operated
and maintained
in accordance with the applicable operation and instruction manuals. All warranty claims must be submitted through and
approved by factory authorized repair stations.
This warranty does not apply to normal wear, orto itemswhose life is dependenton their use and care, such as belts, cords, switches, hoses,
rubber parts, electrical motor components
or adjustments. Parts manufactured by Minuteman are covered by and subject to the warranties
and/or guarantees
of their manufacturers. Please contact Minuteman for procedures in warranty claims against these manufacturers.
Special warning to
purchaser- Use of replacement filters and/or prefilters not manufactured by Minuteman or its designated licensees, will
void all warranties expressed or implied. A potential health hazard exists without original equipment replacement.
All warranted items become the sole property
of Minuteman or its original manufacturer, whichever the case may be.
Minuteman disclaims any implied warranty, including the warranty
of merchantability and the warranty of fitness for a particular purpose.
Minuteman assumes no responsibility for any special, incidental or consequential damages.
This limited warranty is applicable only
in the U.S.A. and Canada, and is extended only to the original user/purchaser of this product.
Customers outside the U.S.A. and Canada should contact their local distributorfor exportwarranty policies. Minuteman is not responsible for
costs
or repairs performed by persons other than those specifically authorized by Minuteman. This warranty does not apply to damage from
transportation, alterations by unauthorized persons, misuse
or abuse of the equipment, use of non-compatible chemicals, or damage to
property,
or loss of income due to malfunctions of the product.
If a difficulty develops with this machine, you should contact the dealer from whom it was purchased.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state. Some states do not allow the
exclusion or limitation
of special, incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above
exclusions and limitations may not apply to you.
18

Cord Electric Group: Three years parts, two years labor, ninety days travel (Not to exceed two hours)
Exceptions ..........
Model
Port A Scrub
MPV 13
MPV 14 & 18
V Series Upright Vacuums
Rapid Air Blower
Explosion Proof Vacuum
X12, X12H &TRS 14
E17 &E20 Electric Scrubbers
Pneumatic Vacuums
Description
Battery Operated Group
Sweepers
Internal Combustion Group
Exception: PAS 148
Battery Chargers:
Replacement Parts:
Batteries:
Polyethylene Plastic Tanks:
Parts Labor Poly
1 yr 6 months 10 yrs
1 yr 0 0
2 yrs 1 yr 0
1 yr 1yr 0
1 yr 1 yr 10 yrs
1 yr 1 yr 0
1 yr 1 yr 10 yrs
1 yr 6 months 10 yrs
3 yr 1 yr 0
Parts Labor Poly
3 yrs 2 yrs 10
1 yr 1 yr 10
1 yr 1 yr
10
1 yr 1 yr 10 yr
One year replacement
Ninety days
Travel
0
0
0
0
0
0
0
0
0
Travel
90 days
90 days
90 days
Not to exceed two hours
0
0-3 months replacement, 4-12 months pro-rate
Tanks have 1
Oyr warranty, no additional labor
19

Minuteman®
Excellence Meets Clean
Minuteman International · 14N845 U.S. Route 20 · Pingree Grove, Illinois 60140 USA
Phone [phone] www.minutemanintl.com
A
Member of the Hako Group
988736
Rev* 07/09