Mitsubishi Electric SEZ-KD NA Series User manual

Photo
Speci cations
MSZ-A09/12/15/17/24/NA
MSY-A15/17/24NA
SEZ-KD**NA
SLZ-KA
M-NET Interface
MAC-399IF-E
Unit : mm
Descriptions
Applicable Models
Outline and Dimensions
2000
70
54
10
15
40
140
160
Indoor only (ambient temperature: 0 to 40℃, no condensation)
Operating conditions
12VDC (supplied from indoor unit)
Power
Dedicated 5-wire cable
Indoor unit connecting cable
Weight 350g (including indoor unit connecting cable)
TO BE CONFIRMED
Enables centralized and individual control of
M series and S series models with new
-A control using M-NET.
MSZ-FD09/12NA
MSZ-GE09/12/15/18NA
MSZ/Y-D30/36NA
MSZ/Y-GA24NA
Cntrls. 1

1. Safety Instructions
• Read all Safety Instructions before using this device.
• This manual contains important safety information. Be sure to comply with all instructions.
• After installing the Interface, provide this Installation Manual to the user.
Instruct users to store their room air conditioner Instruction Manual and Warranty in a safe location.
Warning
(Improper handling may have serious consequences, including injury or death.)
■Users should not install the Interface on their own.
Improper installation may result in fire, electric shock, or damage/water leaks if the Interface unit falls. Consult the dealer
from whom you purchased the unit or professional installer.
■The Interface should be securely installed in accordance with the enclosed Installation Instructions.
Improper installation may result in fire, electric shock, or damage/water leaks if the Interface unit falls.
■The unit should be mounted in a location that can support its weight.
If installed in an area that cannot support the unit, the Interface unit could fall and cause damage.
■Securely attach the electrical component cover to the Interface unit.
If the electrical component cover of the Interface unit is not securely attached, dust or water penetration could occur,
resulting in a fire or electric shock.
■Mitsubishi components or other designated components must be used for installation.
Improper installation may result in fire, electric shock, or damage/water leaks if the Interface unit falls.
■When performing electrical work, adhere to the technical standards regarding electrical equipment and the interior
wiring standards, follow the instructions provided in the Instruction Manual, and be sure to use a dedicated circuit.
Inadequate circuit capacity or improper installation could result in a fire or electric shock.
Contents
1. Safety Instructions .......................................................................................................................... 2
2. Before Installation ........................................................................................................................... 3
3. Mounting the M-NET Interface Unit ................................................................................................ 4
4. Setting the Switches ....................................................................................................................... 5
5. Connecting the M-NET Interface to indoor unit .............................................................................. 6
6. Connecting the M-NET Interface, the Power Supply, and the ME Remote Controller .................... 7
7. Notes Regarding Use ..................................................................................................................... 8
8. Table of Functions Activated from the ME Remote Controller/System Controller........................... 9
9. Specifications.................................................................................................................................. 9
Cntrls. 2

2. Before Installation
2.1. How to Use the M-NET Interface
Caution
When using a packaged air conditioner (city-multi) system remote controller, you cannot register packaged air condi-
tioners and room air conditioners in the same group. In this case, register the Packaged and room air conditioner in
different groups.
■Functions
Centralized and individual management of M/P/S series using M-NET(*).
* A type of packaged air conditioner control (city-multi)
■Related Products Sold Separately
• ME Remote Controller PAR-F27MEA
• Centralized Controller G-50A
• System Remote Controller PAC-SF44SRA
• ON/OFF Remote Controller PAC-YT40ANRA
• Schedule Timer (M-NET) PAC-YT34STA
• Power supply unit PAC-SC50KUA
■Sample of System Configuration (only M/S series outdoor-unit)
Sample configuration of a system using a centralized controller
1Centralized controller (M-NET)
2Power supply unit
3Packaged air conditioner system
4M-NET Interface
5Indoor unit
6ME Remote Controller
* The number of units that can be connected to the
centralized controller (G-50A) is max. 50, including
packaged and room air conditioners. The wiring
from the M-NET Interface to the centralized
controller can have a maximum length of 500 m.
The wiring from the M-NET Interface to the ME
Remote Controller can have a maximum length of
10 m.
For details, see the MELANS Catalog and the
instruction manuals for the Centralized Controller
and ME Remote Controller.
2.2. Accessory
Before installing the device, make sure you have all the necessary parts.
■Accessory
1Interface unit (with 5-core connecting cable) 1
2Mounting brackets 1
3Screws for mounting 23.5×12 4
4Cushioning material (with adhesive) 1
5Cord clamp for mounting (small) 2
6Mounting cord clamp (large) 2
7Screws for mounting 5and 63.5×12 2
8
Screw for mounting 5and 64×10
1* Use this when mounting cord clamp to and around M
series.
9
Screw for mounting 5and 64×16
1* Use this when mounting cord clamp together with the
parts of M series.
0Cable ties 4
AFasteners (for joining the lead wires) 5
BCord clamp for wiring 5
CScrews for mounting B3.5×12 5
DInterface case mounting screws 3.5×12 2
■Items to Prepare at the Installation Site
AConnection wiring (centralized controller)
Shield wiring CVVS/CPEVS
BConnection wiring (for connecting the ME Remote Controller)
Remote control wires (2-core sheath wire 0.3 mm2)
Related parts sold separately
C* Prepare the necessary number of parts sold separately as needed
for your system.
13
2
6
6
4
4
5
5
* CPEVS ; PE insulated PVC jacketed shielded communication cable
* CVVS; PVC insulated PVC jacketed shielded control cable
PE: Polyethylene PVC: Polyvinyl chloride
Cntrls. 3

3. Mounting the M-NET Interface Unit
The M-NET Interface unit should be placed in a location where the 5-core connecting cable from the interface can reach an indoor
unit. Do not extend the 5-core connecting cable.This will cause the device to malfunction.
Mount the interface unit securely to a pillar or wall using 2 or more screws.
Mounting screws 3
■When Using Wall Mounting Brackets 2
1
Attach the wall mounting brackets 2to the interface unit
1using 2 mounting screws 3.
Mounting screws C
Interface unit 1Wall mounting
brackets 2
Mounting
screws 3
Cord clamp for
wiring B
■When Mounting Directly to a Wall
Mount the interface unit 1case to the wall using the mounting
screws 3.
* When mounting the interface unit 1using a cushioning
material 4, be sure to mount it in a location where it will not
fall.
Interface case
mounting screws D
Mounting
screws 3
Cushioning material 4
Interface unit 1
2
Mount the unit to a pillar or wall using 2 mounting screws 3.
When mounting the interface unit 1inside a ceiling
or wall, install an access door to facilitate mainte-
nance.
When the interface unit 1is mounted
above an indoor unit, it should be
positioned 40 mm or more away from the
unit to ensure that ceiling grills can be
removed.
40 mm or more
Attach the 5-core connecting cable of the interface unit
1here. Store extra 5-core connecting cable in the
ductwork space behind the indoor unit.
* If there is any slack in the 5-core connecting cable,
use a fastener Ato keep it in place.
Cntrls. 4

4. Setting the Switches
If the system is not configured correctly, the unit will not function properly.You may be unable to control the functions of the indoor
unit from the System Controller/ME Remote Controller or functions not available on the indoor unit could appear on the System
Controller/ME Remote Controller display. You should therefore ensure that the system is properly configured before connecting
the power supply.
■SW500 No. 1, No. 2 - Not in use
These should be set to OFF (if set to ON, the device will not communicate properly with the System Controller).
■SW500 No. 3 - Power On/Off Settings
This setting indicates whether the indoor unit should be turned off or on when power is supplied to the indoor unit or M-NET
Interface.
Turn on with power No
[Unit remains off when the power is supplied.]
■SW500 No. 4 - Availability of purifier or fan mode
If there is no “Purifier” button on the wireless remote control, and if the word “Fan” does not appear when the “Mode” button is
pressed, the purifier and fan modes are not available (set to OFF).
Turn on with power Yes
[Unit turns on when the power is supplied.]
Has a purifier or fan mode
Does not have a purifier or fan mode
ON
Does have an auto op-
eration mode
Does not have a fan os-
cillation setting
Does not have a fan di-
rection setting
Cooling unit only
■SW500 No. 5–No. 8 - M series Function Check
Function description
Availability of automatic op-
eration mode (a mode that al-
lows the air conditioner to de-
termine whether to select
cooling or heating).
Availability of a fan oscillation
setting
Availability of a fan direction
setting
Availability of a heating mode
SW500
No. 5
No. 6
No. 7
No. 8
How to check a function
If “Auto” is not displayed when you push the “Mode” but-
ton on the wireless remote control, the auto operation
mode is not available (OFF).
If “Oscillate” is displayed when you push the “Fan Direc-
tion” button on the wireless remote control, the fan os-
cillation setting is available (OFF). (If there is no “Fan
Direction” button, the setting is OFF.)
If there is a “Fan Direction” button on the wireless re-
mote control, the fan direction setting is available (OFF).
If “Heat” appears when you push the “Mode” button on
the wireless remote control, the unit is a model that of-
fers both cooling and heating (OFF).
OFF
Does not have an auto
operation mode
Has a fan oscillation set-
ting
Has a fan direction set-
ting
Dual cooling and heating
model
■SW510, SW501 - Address settings
Specifies the address settings for centralized management (address settings can be set from 01–50).
SW510 sets the 10s position of the address and SW501 sets the 1s position of the address.
For example, to set a unit to the address 25, set SW510 to “2” and SW501 to “5”.
1s position
Self-Address
10s position
Cntrls. 5