MJ LED LIGHTNING MJ-1019-4IN1 User manual

4-BEAM MOVING HEAD SYSTEM
MJ-1019-4IN1
INSTRUCTION MANUAL
======PROFESSIONAL LED LIGHTING ========
Thank you for choosing our LED beam moving head light. For the sake of your safety, Please
read and follow these instructions carefully and keep this manual in a safe place for future
reference.

2
Catalogue
Chapter Page
Safe Usage Of The Product -----------------------------------------------------------------------------------------3
Install The Equipment ------------------------------------------------------------------------------------------------4
Power Code Connection ---------------------------------------------------------------------------------------------4
DMX Connection ------------------------------------------------------------------------------------------------------5
DMX Terminator -------------------------------------------------------------------------------------------------------6
Function Set --------------------------------------------------------------------------------------------------------------6
Menu Function Description ----------------------------------------------------------------------------------------------6
Maintenance -------------------------------------------------------------------------------------------------------------7
Keeping The Product Clean -----------------------------------------------------------------------------------------7
Trouble Shooting--------------------------------------------------------------------------------------------------------7
Equipment and Appendix---------------------------------------------------------------------------------------------8
Channel List---------------------------------------------------------------------------------------------------------------8
Technical Parameters---------------------------------------------------------------------------------------------------10
☆Important notice:
·In this instruction for use contains about the installment and the use aspect important information of the LED moving
head. When installing and using, you need to look this usage instruction strictly.
·Before open the LED moving head and if you want to do the repair work, please make sure the power source is at the
separation condition.
·Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and the unit are
in good condition before installation and use. Should there be any damage caused by transportation, consult your dealer
and do not use the unit. Any damage caused by improper use will not be assumed by the manufacturer or dealer.
Attention: Unceasingly carries on the product improvement about our company the policy, in this instruction booklet
carries the data will have the possibility to be able to change in the future, when no longer separate notice change matters
concerned. Our company retains when the product improvement changes the related specification the authority. This
instruction booklet publisher cannot be responsible regarding this instruction booklet in information accuracy, also cannot
the related consequence which causes regarding these information be responsible.

3
SAFE USAGE OF THE PRODUCT
When unpacking and before disposing of the carton, check there is no transportation damage before
using the product. Should there be any damage caused by transportation, consult your dealer and do
not use the apparatus.
The product is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain
and moisture, excessive heat, humidity and dust. Do not allow contact with water or any other
liquids.
The product is not designed or intended to be mounted directly on to inflammable surfaces
The product is only intended for installation, operation and maintenance by professional person.
The product must be installed in a location with adequate ventilation, at least 50cm from adjacent
wall surfaces. Be sure that no ventilation slots are blocked.
Do not product the beam onto inflammable surfaces, minimum distance is 5m.
Avoid direct exposure to the light from the lamp. The light is harmful to the eye.
Do not attempt to dismantle or modify the projector in any way.
Electrical connection must only be carried out by qualified personnel.
Before installation, ensure that the voltage and frequency of power supply match the power
requirements of the projector.
It is essential that each projector is correctly earthed and that electrical installation conforms to all
relevant standards.
Do not connect this device to any other types of dimmer apparatus.
Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the
power-cord come into contact with other cables. Only handle the power-cord by the plug. Never pull
out the plug by tugging the power-cord.
Keep the optical system clean. Do not touch the LED lens with bare hands.
The product should always be installed with a secondary safety fixing. On the projector base brink,
there is a hole for the safety cord provided. It should be attached as shown in “installing the
projector” section.
LED lens shall be changed if they have become visibly damaged to such an extent that their
effectiveness is impaired, for example by cracks or deep scratches.
Exterior surface temperatures of the luminaire after 5 minutes operation is 40°C， when steady state is
achieved 50°C.
There is no user serviceable parts inside the projector, do not open the housing and never operate the
product with the covers removed.
If you have any questions, don’t hesitate to consult your dealer or manufacturer.
★Always disconnect from the mains, when the device is not in use or before cleaning it or
before attempting any maintenance work !

4
Install The Equipment:
Use 2pcs clamp (need to purchase).Use clamp fix with light hook which in the packing box with
light, then use screw install to the bottom of lamp. Hang the fixture on the structure and fasten the
screws attached to each clamp. Make sure the light is installed reliable, and confirm the light which
you fixed is strong enough for hanging the light. Base on safety reason, please according to the
above picture using safety wire cross the light to make it strong enough again.
Warning!
1．Hook and clamp only use for hanging the light. Do not use clamp as a tool to move fixtures.
2．Don't use the handle of the moving head light to fixed or lift!
Power Code Connection:
Connect the power cord as follows:
L (live) =brown
E (earth) =yellow/green
N (neutral) =blue
Use the plug provided to connect the mains power to the projector paying attention to the voltage and
frequency marked on the panel of the projector. It is recommended that each projector be supplied
separately so that they may be individually switched on and off.
★It is essential that each projector is correctly earthed and the electrical installation conforms
to all relevant standards.

5
DMX Connection:
Connection between the controller and a projector and between one projector and another must be
made with a 2 core-screened cable, with each core having at least a 0.5mm diameter. Connection to
and from the projector is via cannon 3 pin (which are included with the projector) XLR plugs and
sockets. The XLR's are connected as shown in the figure above.
Note: Care should be taken to ensure that none of the pins touch the metallic body of the plug or each
other. The body of the plug is not connected in any way. The XLED 590 accepts digital control
signals in protocol DMX512 (1990).
Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the
second fixture’s input and connect the rest fixtures in the same way. Eventually connect the last
fixture’s output to a DMX terminator as shown in the figure below.

6
DMX Terminator:
In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a
DMX terminator. This prevents electrical noise from disturbing and corrupting the DMX control signals.
The DMX terminator is simply an XLR connector with a 120Ω (ohm) resistor connected across pins
2 and 3, which is then plugged into the output socket on the last projector in the chain. The
connections are illustrated below.
Function Set:
Menu down up Enter
Use button switch and LED display, can set the address code and function code easily.
Check or modify lighting function settings, Press the MENU button. LED display panel will display function menu
of lighting. Function operation menu all have corresponding submenu. Each menu all represent the specific
functions of lamps, specific see below "operation menu" section.
Set or browse function setting of lamp, Press UP or DOWN button.
Press ENTER button to save your changes or to ENTER submenu, Press UP or DOWN can change value (Plus or
reduce number).
According to the ENTER key to return to the last menu.
Menu Function Description：
No.
Display
Function description
1
A001
6 Channel Address Code（001—512）
Down and up button plus or reduce address code value
2
H001
29 Channel Address Code（001—512）
Down and up button plus or reduce address code value
3
CC00
Colorful jump （01—99）
Down and up button change jump speed
4
CP00
Colorful fade（01—99）
Down and up button change fade speed
5
DE00
Colorful Pulse （01—99）

7
Down and up button change jump speed
6
FF00
Colorful Running（01—99）
Down and up button change speed
7
BEB1
Colorful sound control __1
8
ID00
DMX512 ID，（00—51）
When the ID=0 the ID off
When press Enter key,Down and UP key can modify DMX 512 ID value.When
ID started,each time of start this light will display ID value in 5 secnods
9
FROM
Slave Mode
Maintenance:
To prolong the life of the projector, some maintenance work has to be done to ensure the LED optical system in
good condition. If the projector does not function, check the fuses on the power socket of the projector, they should
only be replaced by fuses of the same specification. Should these be damaged, call a qualified technician before
replacement. The projector has thermal protection device that will switch off the projector in case of overheating.
Should either of these operate, check that the fans are not blocked, and if they are dirty, clean them before
switching on the projector again. Check that the fans are operational, if not, call a qualified technician.
☆Any maintenance work should only be carried out by qualified technicians.
Keeping The Product Clean:
To ensure the reliability of the projector, it should be kept clean. It is recommended that the fans should be cleaned
every 15 days. LED lens should also be regularly cleaned to maintain an optimum light output.
Cleaning frequency depends on the environment in which the fixture operates: damp, smoke or particularly dirty
surroundings can cause greater accumulation of dirt on the unit's optics. A soft cloth and typical glass cleaning
products should be used for cleaning. It is recommended to clean the external optics at least once every 15 days.
☆Do not use any organic solvent, e.g. alcohol, to clean housing of the apparatus.
Trouble Shooting:
Problem
Answer
The LED moving head light doesn’t switch on.
Check the fuse the power socket
Although shines, but the LED moving head lamp
doesn’t accept the instruction of the controller.
Check the digital start address and also check the
connection situation of the communication control
line
LED moving head lamp only can work
intermittently.
Inspect the power supply and voltage is whether
normal.
Do not receive the DMX512 signal.
Whether the signal lines do contact well or broken.
The light beam appears gloomily.
Check that the heat dissipation system is running
normally or Inspect the optics part is whether clean.
☆Other maintain work should by the specialist which has the experience to carry on.

8
Equipment and Appendix:
The packing list of this light as follows:
☆Led moving head light 1pcs
☆Power Cable 1pcs
☆XLR connector 1unit
☆Light Hook 2pcs
☆The Product of Instruction 1pcs
Channel List:
6Channel
Channel
Function
Function Description
CH1
X
Pan rotation
CH2
Y
Tilt rotation
CH3
R dimmimg
R dimming from dark to bright
CH4
G dimming
G dimming from dark to bright
CH5
B dimming
B dimming from dark to bright
CH6
Wdimming
W dimming from dark to bright
29Channel
Channel
Function
Function Description
CH1
Main
dimming
Main dimming from dark to bright
CH2
Main strobe
Main strobe from slow to quick
CH3
R1 dimming
R1 dimming from dark to bright
CH4
G1 dimming
G1 dimming from dark to bright
CH5
B1 dimming
B1 dimming from dark to bright
CH6
W1 dimming
W1 dimming from dark to bright
CH7
R2 dimming
R2 dimming from dark to bright
CH8
G2 dimming
G2 dimming from dark to bright
CH9
B2 dimming
B2 dimming from dark to bright
CH10
W2dimming
W2 dimming from dark to bright
CH11
R3 dimming
R3 dimming from dark to bright
CH12
G3 dimming
G3 dimming from dark to bright
CH13
B3 dimming
B3 dimming from dark to bright

9
CH14
W3dimming
W3 dimming from dark to bright
CH15
R4 dimming
R4 dimming from dark to bright
CH16
G4 dimming
G4 dimming from dark to bright
CH17
B4 dimming
B4 dimming from dark to bright
CH18
W4dimming
W4 dimming from dark to bright
CH19
X1
X1 rotation
CH20
Y1
Y1 rotation
CH21
X2
X2 rotation
CH22
Y2
Y2 rotation
CH23
X3
X3 rotation
CH24
Y3
Y3 rotation
CH25
X4
X4 rotation
CH26
Y4
Y4 rotation
CH27
Speed
1--250 Motor speed from fast to slow
251--255
CH28
Macro
0--30：DMX 17channel control
31--50：Fade；(the motor can be control)
51--70：Pulse(the motor can be control)
71--90：Running mode (the motor can be control)
91--110：Sound 1；(the motor can be control)
111--130：Sound2; (the motor can be control)
131--150：Fade；(the motor can’t control)
151--170：Pulse(the motor can’t control)
171--190：Running mode (the motor can’t control)
191--210：Sound 1；(the motor can’t control)
211--230：Sound 2 (the motor can’t control)
231--255：No funnction
CH29
DMX512 ID
ID 1 5--9
ID 2 10--14
ID 3 15--19
ID 4 20--24
........ .........
ID 51 255
It can be control 50pcs light, If the ID code in the same
address

10
Technical Parameters:
Voltage: A100V-240V; 50/60Hz
Power Consumption: 100W (220V)
LED Bulbs: 10W*4in1 LEDs LED
LED Current: 500mA
LED Lifetime: 50000Hours
Adjusts the light: 0-100 electron adjusts the light
Strobe: 1-25/second high speed strobe
Head Movement: Pan 540°, Tilt 270°, with auto
position correction and electronic replacement function.
Beam Angle: 2°
Control mode: DMX 512, Stand –alone mode, Self-test mode, Sound, Master/slave
DMX Channel: 6 / 29CH
Control Panel: LED display panel
IP Grade: IP33
Work Environment Temperature: -20°C~40°C
Net weight:9.5KG
Gross Weight: 10.8 kg
Package Size: L1100×W190×H140 mm