MK Diamond Products MK-101-24HD System manual

12.2014
MK-101-24HD
OWNER’S MANUAL &
OPERATING INSTRUCTIONS
www.mkdiamond.com
Caution: Read all safety and operating instructions before
using this equipment. This owners manual MUST
accompany the equipment at all times.
Revision 103
Manual Part No. 169700
MK-101-24HD Part # 169212

2
INTRODUCTION
Congratulations on your purchase of a MK-101-24HD Tile Saw. We are certain that you will be
pleased with your purchase. MK Diamond takes pride in producing the finest construction power
tools and diamond blades in the industry.
Operated correctly, your MK-101-24HD should provide you with years of service. In order to help
you, we have included this manual. This owners manual contains information necessary to operate
and maintain your Tile Saw safely and correctly. Please take a few minutes to familiarize yourself
with the saw by reading and reviewing this manual.
If you should have questions concerning your saw, please feel free to call our friendly customer
service department at: 800 421-5830
Regards,
MK Diamond
NOTE: For your (1) one year warranty to be effective, complete the warranty
card (including the Serial Number) and mail it in as soon as possible.
NOTE THIS INFORMATION FOR FUTURE USE:
MODEL NUMBER:
SERIAL NUMBER:
PURCHASE PLACE:
PURCHASE DATE:

3
TABLE OF CONTENTS
SAFETY
Safety Messages 4
General Safety Precautions & Hazard Symbols 4-7
California Proposition 65 Message 8
Canadian French Safety Translation 9-14
Electrical Requirements 15-18
Safety Label Locations 20
Product Specications 21
UNPACKING, TRANSPORT and ASSEMBLY
Unpacking 22
Contents 22
Transport 23
Stand (Optional) 23
Assembly 24-26
SETUP, STARTUP, ADJUSTMENT, OPERATION and SHUTDOWN
Setup 27-29
Operation 30-33
Cutting Head Adjustment 34-35
Cleanup 36
MAINTENANCE AND TROUBLESHOOTING
Maintenance 37-42
Troubleshooting 43-47
EXPLODED VIEW AND PARTS LIST
Exploded View & Parts List 48-55
ACCESSORIES ORDERING and RETURN INSTRUCTIONS
Theory of Diamond Blade 56
Accessories 57
Ordering Information 58
Return Material Policy 58
Packaging Instructions 58
CONTACT and LIMITED WARRANTY
Contact and Warranty 59

4
MK-101-24HD SAFETY
Read and follow all safety, operating and maintenance instructions. Failure to read and follow
these instructions could result in injury or death to you or others. Failure to read and follow these
instructions could also result in damage and/or reduced equipment life. Safety warnings and
guidelines do not by themselves eliminate danger. They are not substitutes for proper accident
prevention procedures and good judgement.
SAFETY MESSAGES
A Damage Prevention Message is to inform the user of important information and/or instructions that
could lead to equipment or other property damage if not followed. Information Messages convey
information that pertains to the equipment being used. Each message will be preceded by the word
NOTE, as in the example below.
DAMAGE PREVENTION AND INFORMATION MESSAGES
NOTE: Equipment and/or property damage may result if these instructions are not followed.
SAFETY PRECAUTIONS
GENERAL SAFETY PRECAUTIONS AND HAZARD SYMBOLS
A safety message alerts you to potential hazards that could hurt you or others. Each safety message is
preceded by a safety alert symbol ( ) and one of three words: DANGER, WARNING, or CAUTION.
DANGER You WILL be KILLED or SERIOUSLY INJURED if you DO NOT follow directions.
WARNING You CAN be KILLED or SERIOUSLY INJURED if you DO NOT follow directions.
CAUTION You CAN be INJURED if you DO NOT follow directions. It may also be used to
alert against unsafe practices.
ALWAYS read this Owner’s Manual before operating the machine. DO NOT operate or
service this equipment before reading this entire manual. Read and understand all warn-
ings, instructions and controls on the machine. Know how to stop the equipment quickly in
case of emergency. It is the operators responsibility to use this machine under safe work-
ing conditions and conform with federal, state and local codes or regulations pertaining to
safety, air, pollution, noise etc...
ALWAYS keep the Blade and Belt Guards in place. DO NOT operate this machine with any
guard or safety device removed. A Guard, or any damaged part should be repaired or
replaced immediately.
NEVER operate this equipment without proper protective clothing, shatterproof
glasses, steel-toed boots and other protective devices required by the job. Non-slip
foot wear is recommended.
ON
(
(
))
ON
(
(
))
ON
(
(
))
ON
((
))
ON
(
(
))
ON
(
(
))
ON
(
(
))
ON
(
(
))
In order to prevent injury, the following safety precautions and symbols should be followed at all times!

5
MK-101-24HD SAFETY
ON
(
(
))
ON
(
(
))
ON
(
(
))
All visitors and children should be kept a safe distance from work area. Maintain a safe
operating distance to other personnel.
KEEP CHILDREN AWAY
MAKE THE WORKSHOP KID PROOF
Make the workshops kid proof by using padlocks, master switches or by removing starter keys.
ROTATING PARTS
Keep hands, feet, hair, and clothing away from all moving parts to prevent injury. Never oper-
ate the motor with covers, shrouds, or guards, removed.
OVER SPEED
NEVER tamper with the governor components or settings to increase the maximum speed.
Severe personal injury and damage to the engine or equipment can result if operated at
speeds above maximum.
ELECTRICAL SHOCK
NEVER touch electrical wires or components while the engine is running. Exposed, frayed or
worn electrical wiring and plugs can be sources of electrical shock which could cause severe
injury or burns. Do not touch the plug with wet hands.
ALWAYS avoid inhalation of and skin contact with silica dust and/or mist. Provide proper
dust removal. Use dust-collection system when applicable.
NEVER operate the machine in an explosive atmosphere or near combustible materials.
Sparks from the cutting-action of this machine can ignite flammable materials, liquids, gases
or dust.
This equipment should not be operated by persons under 18 years of age.
ALWAYS wear approved respiratory, head, ear and eye protection
when operating this machine.
Before starting the engine/motor, be sure the ON/OFF switch is in the OFF position to pre-
vent accidental starting. Place the ON/OFF switch in the OFF position before performing any
service operation. ALWAYS place the power ON/OFF switch in the OFF position when the
saw is not in use.
ACCIDENTAL STARTS!
PERSONAL PROTECTIVE EQUIPMENT
Engine components can become extremely hot from operation. To prevent severe burns,
do not touch these areas while the engine is running, or immediately after it is turned off.
Never operate the engine with heat shields removed.
HOT PARTS!
ON
(
(
))
ON
(
(
))
ON
(
(
))
ON
(
(
))
ON
(
(
))
ON
(
(
))
ON
(
(
))
ON
(
(
))
ON
(
(
))
ON
(
(
))
ON
(
(
))
DO NOT FORCE THE TOOL
A power tool will do a job better and safer operating at the rate for which it was designed.
DO NOT force a tool or an attachment to do a job that it was not designed to do.
ON
(
(
))

6
MK-101-24HD SAFETY
Consult the owner’s manual for recommended accessories. Using improper accessories
may increase the risk of personal or by-stander injury. Unauthorized equipment
modifications will void all warranties. Manufacturer does not assume responsibility for any
accident due to equipment modifications.
ALWAYS ensure that the machine is on level ground before using.
Serious injury could occur if a power tool is tipped, or if a cutting tool is unintentionally
contacted.
When loading or unloading the machine, use caution. Remove the blade prior to hoisting,
loading and transporting the machine.
USE RECOMMENDED ACCESSORIES
NEVER STAND ON THE TOOL
TRANSPORT
Form a habit of checking to see that keys and adjusting wrenches are removed from
the power tool before it is turned on.
Cluttered work areas and benches invite accidents. Keep area around machine clear of
obstructions which could cause persons to fall.
DO NOT operate equipment in dangerous or hazardous environments. DO NOT use power
tools in damp or wet locations nor expose them to rain. Always keep the work area well
lighted.
REMOVE ADJUSTING KEYS AND WRENCHES
KEEP WORK AREA CLEAN
DO NOT USE IN DANGEROUS PLACES
MAINTAIN TOOLS WITH CARE
Keep tools clean and maintained for the best and safest performance. Always follow
maintenance instructions and examine the machine before use. If any abnormal vibrations
or noises occurs, turn off machine immediately and have the problem corrected before
further use.
DISCONNECT TOOLS
Power tools should always be disconnected before servicing, adjusting or when changing
accessories, such as blades, bits, cutters, and the like.
DO NOT OVERREACH
Keep proper footing and balance at all times by not overreaching.
ON
(
(
))
ON
(
(
))
ON
(
(
))
ON
(
(
))
ON
(
(
))
ON
(
(
))
ON
(
(
))
ON
(
(
))
ON
(
(
))
ON
(
(
))
SECURE WORK
Clamps or a vise should be used to hold work whenever practical. Keeping your hands free
to operate a power tool is safer.
ON
(
(
))
USE PROPER APPAREL
DO NOT wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry that may
be caught in moving parts. Non-slip footwear is recommended. Wear protective hair cover-
ing to contain long hair.
ON
(
(
))

7
MK-101-24HD SAFETY
Before using a power tool, check for damaged parts. A guard or any other part that is
damaged should be carefully checked to determine if it would operate properly and
perform its intended function. Always check moving parts for proper alignment or binding.
Check for broken parts and mountings and all other conditions that may affect the
operation of the power tool. A guard, or any damaged part, should be properly repaired or
replaced. Always check the machine for loose bolts before starting.
A blade or cutter should always be installed so that rotation is in the direction of the
arrow imprinted on the side of the blade or cutter. It should correspond with the rotational
direction of the motor. Always feed work into a blade against the direction of rotation.
TURN POWER OFF - Do not leave a tool until it comes to a complete stop. ALWAYS
turn a power tool OFF when leaving the work area, or, when a cut is finished.
NEVER LEAVE A TOOL UNATTENDED
CHECK FOR DAMAGED PARTS
DIRECTION OF ROTATION
NEVER disconnect any "emergency or safety devices". These devices are intended for
operator safety. Disconnection of these devices can cause severe injury, bodily harm, or
even death! Disconnection of any of these devices will void all warranties. Unauthorized
equipment modifications will void all warranties. Manufacturer does not assume
responsibility for any accident due to equipment modifications.
NEVER operate this equipment under the influence of drugs or alcohol.
NEVER operate this equipment when not feeling well due to fatigue, illness or taking medicine.
NEVER use this machine with any cutter designed for woodworking.
ON
(
(
))
ON
(
(
))
ON
(
(
))
ON
(
(
))
ON
(
(
))
ON
(
(
))
ON
(
(
))
ON
(
(
))
ON
(
(
))
ON
(
(
))
ON
(
(
))
ON
(
(
))
On belt driven equipment, overtensioning of belts will result in premature crank and/or bearing
failure.
Whenever necessary, replace nameplate, operation and safety decals when they become
difcult to read.
ALWAYS store equipment properly when it is not being used. Equipment should be stored in
a clean, dry location out of the reach of children
DO NOT lend or rent this equipment without including the Owner's Manual and the Engine/
Motor Manufacturer's Manual.
Check the chemical properties of the material to be cut/grinded and follow all EPA/OSHA
Regulations.

8
MK-101-24HD SAFETY
Sawing and drilling generate dust. Excessive airborne particles may cause irritation to eyes, skin and
respiratory tract. To avoid breathing impairment, always employ dust controls and protection suitable
to the material being sawed or drilled; See OSHA (29 CFR Part 1910.1200).
WARNING
CALIFORNIA PROPOSITION 65 MESSAGE
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities con-
tain chemicals known (to the State of California) to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
 Lead, from lead-based paints
 Crystalline silica from bricks, cement and other masonry products
 Arsenic and chromium, from chemically treated lumber
For further information, consult the following sources:
http://www.osha.gov/dsg/topics/silicacrystalline/index.html
http://www.cdc.gov/niosh/docs/96-112/
http://oehha.ca.gov/prop65/law/P65law72003.html
http://www.dir.ca.gov/Title8/sub4.html
Your risk from these exposures varies depending on how often you do this type of work. To reduce
your exposure to these chemicals, work in a well-ventilated area, and work with approved safety
equipment, such as dust masks that are specially designed to lter out microscopic particles. Where
use of a dust extraction device is possible, it should be used. To achieve a high level of dust collec-
tion, use an industrial vacuum cleaner.
SILICA DUST WARNING
Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in their composition
may give off dust or mists containing crystalline silica. Silica is a basic component of sand, quartz,
brick clay, granite and numerous other minerals and rocks. Repeated and/or substantial inhalation of
airborne crystalline silica can cause serious or fatal respiratory diseases, including silicosis. In ad-
dition, California and some other authorities have listed respirable crystalline silica as a substance
known to cause cancer. When cutting such materials, always follow respiratory precautions.
Use appropriate NIOSH-approved respiratory protection where dust hazard may occur. Paper masks
or surgical masks without a NIOSH approval number are not recommended because they do little to
protect the worker. For more information about respirator programs, including what respirators have
received NIOSH approval as safe and effective, please visit the NIOSH website at:
http://www.cdc.gov/niosh/topics/respirators
Observe OSHA regulations for respirator use (29 C.F.R.§1910.134).
Visit http://www.osha.gov for more information.
ON
(
(
))

9
MK-101-24HD DE SÉCURITÉ
Lisez et suivez toutes les consignes de sécurité, d'utilisation et d'entretien. Ne pas lire et suivre ces
consignes pourrait entraîner des blessures, voire la mort, pour vous ou d'autres personnes. Ne pas lire
et suivre ces consignes pourrait aussi endommager et/ou raccourcir la durée de vie de l'équipement.
Les avertissements et les directives de sécurité n'éliminent pas, par eux-mêmes, les risques. Ils ne
remplacent pas les mesures efficaces de prévention des accidents et le bon jugement.
MESSAGES DE SÉCURITÉ
Un message de prévention des dommages doit informer l'utilisateur des informations et/ou consignes
importantes, qui, si elles ne sont pas suivies, pourraient endommager l'équipement ou conduire à d'autres
dommages matériels. Les messages d'information transmettent des informations relatives à l'équipement
utilisé.
Chaque message sera précédé par le mot REMARQUE, comme dans l'exemple ci-dessous.
PREVENTION DES DOMMAGES ET MESSAGES D'INFORMATION
REMARQUE : Des dommages à l'équipement et/ou des dommages matériels peuvent survenir si
les instructions ne sont pas suivies.
CONSIGNES DE SÉCURITÉ GÉNÉRALES ET SYMBOLES DE DANGER
Un message de sécurité vous signale les dangers potentiels pour vous ou d'autres personnes.
Chaque message de sécurité est précédé par un symbole d'alerte de sécurité ( ) et par l'un des
trois mots suivants : DANGER, AVERTISSEMENT ou ATTENTION.
DANGER LE NON-RESPECT des consignes entraînera des BLESSURES GRAVES voire
la MORT.
AVERTISSEMENT LE NON-RESPECT des consignes PEUT ENTRAÎNER des BLESSURES
GRAVES voire la MORT.
ATTENTION LE NON-RESPECT des consignes PEUT ENTRAÎNER des BLESSURES. Il
peut également être utilisé pour alerter contre les pratiques dangereuses.
TOUJOURS lire ce manuel avant d'utiliser l'outil. NE PAS utiliser ou entretenir
cet équipement avant d'avoir lu ce manuel en entier. Lire et comprendre tous les
avertissements, instructions et commandes de l'outil. Savoir comment arrêter rapidement
l'équipement en cas d'urgence. Il est de la responsabilité de l'opérateur d'utiliser cet outil
dans des conditions de travail sûres et conformes aux codes et règlements fédéraux,
provinciaux et locaux relatifs à la sécurité, l'air, la pollution, le bruit, etc.
TOUJOURS garder les protections de la lame et de la courroie en place. NE PAS utiliser
cet outil en l'absence d'un dispositif de protection ou de sécurité. Une protection ou toute
pièce endommagée doit être réparée ou remplacée immédiatement.
NE JAMAIS utiliser cet équipement sans vêtements de protection appropriés,
lunettes incassables, bottes à embout d'acier et autres dispositifs de protection
requis par la tâche. Il est conseillé d'utiliser des chaussures antidérapantes.
ON
((
))
ON
((
))
ON
((
))
ON
(
(
))
ON
(
(
)
)
ON
(
(
)
)
ON
(
(
)
)
ON
(
(
)
)
Afin de prévenir les blessures, les consignes et les symboles de sécurité suivants doivent être respectés
en tout temps!

10
MK-101-24HD DE SÉCURITÉ
ON
((
)
)
ON
((
)
)
ON
((
)
)
Tous les visiteurs et les enfants doivent se tenir à bonne distance de la zone de travail.
Maintenir une distance d'utilisation sécuritaire par rapport aux autres membres du personnel.
GARDER LES ENFANTS À L’ÉCART
RENDRE L'ATELIER SÛR POUR LES ENFANTS
Rentre les ateliers sûrs pour les enfants à l'aide de cadenas, d'interrupteurs principaux ou
en retirant les clés de démarrage.
PIÈCES TOURNANTES
Éloigner les mains, les pieds, les cheveux et les vêtements des pièces mobiles pour éviter
des blessures. Ne jamais utiliser le moteur si le couvercle, l'enveloppe de protection ou les
protecteurs ont été retirés.
SURVITESSE
NE JAMAIS modier les composants ou réglages du limiteur de régime an d’augmenter
la vitesse maximale. De graves blessures et des dommages au moteur ou à l’équipement
peuvent en résulter s’il fonctionne à des vitesses supérieures au maximum.
DÉCHARGE ÉLECTRIQUE
NE JAMAIS toucher les ls ou les composants électriques pendant que le moteur est en
marche. Les câbles et ches nus, eflochés ou usés peuvent être des sources de choc
électrique qui pourraient provoquer de graves blessures ou brûlures. Ne pas toucher
la che avec des mains humides.
TOUJOURS éviter l'inhalation et le contact de la peau avec la poussière et/ou un nuage de
silice. Prévoir un système de dépoussiérage adéquat. Utiliser un système de captage des
poussières, le cas échéant.
NE JAMAIS utiliser l'outil dans une atmosphère explosive ou près de matériaux combustibles.
Les étincelles produites par l'action de coupe de cet outil peuvent enflammer les matériaux,
les liquides, les gaz ou les poussières inflammables.
Cet équipement ne doit pas être utilisé par des personnes de moins de 18 ans.
Portez TOUJOURS l'équipement de protection respiratoire,
auriculaire et oculaire homologué lors de l'utilisation de cet outil.
Avant de démarrer le moteur, vériez que le commutateur MARCHE-ARRÊT est en position
ARRÊT (OFF) pour empêcher tout démarrage accidentel. Placez le commutateur MARCHE-
ARRÊT en position ARRÊT (OFF) avant toute intervention d'entretien. Placez TOUJOURS le
commutateur MARCHE-ARRÊT en position ARRÊT (OFF) lorsque vous n'utilisez pas l'outil.
DÉMARRAGES ACCIDENTELS!
ÉQUIPEMENT DE PROTECTION INDIVIDUELLE
Les composants du moteur peuvent devenir très chauds pendant le fonctionnement. Pour éviter
des brûlures graves, ne pas toucher ces zones pendant que le moteur tourne ou immédiatement
après l’avoir arrêté. Ne jamais faire fonctionner le moteur sans les écrans de chaleur.
PIÈCES CHAUDES!
ON
((
))
ON
((
))
ON
((
))
ON
((
)
)
ON
((
)
)
ON
((
)
)
ON
((
)
)
ON
((
)
)
ON
((
)
)
ON
((
)
)
ON
((
)
)
NE PAS FORCER L'OUTIL
Un outil électrique exécutera la tâche mieux et de manière plus sûre s’il est utilisé dans les
limites prévues. NE PAS forcer un outil ou un accessoire à exécuter une tâche pour laquelle
il n’est pas conçu.
ON
((
))