ML Accessories EMRUN Instruction Manual

INSTALLATION & MAINTENANCE MANUAL
EMRUN

These instructions should be read carefully and retained after installation by the end user for
future reference and maintenance.
These instructions should be used to aid installation of the following product:
EMRUN
GENERAL INSTRUCTIONS
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)
and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the
circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
• This product is for indoor use only
• This product is Class I and must be earthed
• This product is IP20 rated
SAFETY
INSTALLATION
• Provide power to the required point of installation
• Remove the two screws on the end of the product (see Fig. 1) and remove the end cap and legend

INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following product:
EMRUN
SAFETY
•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•Please isolate mains prior to installation or maintenance
•Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating
of the circuit cable, fuse or circuit breaker
•Please note the IP (Ingress Protection) rating of this product when deciding the location for
installation
•This product is for indoor use only
•This product is Class I and must be earthed
•This product is IP20 rated
INSTALLATION
•Provide power to the required point of installation
•Remove the two screws on the end of the product (see Fig. 1) and remove the end cap and legend
Fig. 1
•Mark the location of the fixing holes and drill the holes ensuring not to infringe with any gas / water
pipes or electrical cables.
•Drill out one of the 20mm drilling guides on the fitting, and fit a suitable grommet or compression gland
(not included)
•Feed the mains cable into the luminaire, and fix the base to a suitable solid surface
•Wire for non-maintained operation (Fig. 2), maintained operation (Fig. 3) or switched-maintained
operation (Fig. 4) as required. Remove the link between LS and L if not required
Fig. 2 non-maintained
Fig. 3 maintained
Fig. 1
• Mark the location of the fixing holes and drill the holes ensuring not to infringe with any gas / water pipes or
electrical cables.
• Drill out one of the 20mm drilling guides on the fitting, and fit a suitable grommet or compression gland (not
included)
• Feed the mains cable into the luminaire, and fix the base to a suitable solid surface
• Wire for non-maintained operation (Fig. 2), maintained operation (Fig. 3) or switched-maintained operation
(Fig. 4) as required. Remove the link between LS and L if not required
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following product:
EMRUN
SAFETY
•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•Please isolate mains prior to installation or maintenance
•Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating
of the circuit cable, fuse or circuit breaker
•Please note the IP (Ingress Protection) rating of this product when deciding the location for
installation
•This product is for indoor use only
•This product is Class I and must be earthed
•This product is IP20 rated
INSTALLATION
•Provide power to the required point of installation
•Remove the two screws on the end of the product (see Fig. 1) and remove the end cap and legend
Fig. 1
•Mark the location of the fixing holes and drill the holes ensuring not to infringe with any gas / water
pipes or electrical cables.
•Drill out one of the 20mm drilling guides on the fitting, and fit a suitable grommet or compression gland
(not included)
•Feed the mains cable into the luminaire, and fix the base to a suitable solid surface
•Wire for non-maintained operation (Fig. 2), maintained operation (Fig. 3) or switched-maintained
operation (Fig. 4) as required. Remove the link between LS and L if not required
Fig. 2 non-maintained
Fig. 3 maintained
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following product:
EMRUN
SAFETY
•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•Please isolate mains prior to installation or maintenance
•Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating
of the circuit cable, fuse or circuit breaker
•Please note the IP (Ingress Protection) rating of this product when deciding the location for
installation
•This product is for indoor use only
•This product is Class I and must be earthed
•This product is IP20 rated
INSTALLATION
•Provide power to the required point of installation
•Remove the two screws on the end of the product (see Fig. 1) and remove the end cap and legend
Fig. 1
•Mark the location of the fixing holes and drill the holes ensuring not to infringe with any gas / water
pipes or electrical cables.
•Drill out one of the 20mm drilling guides on the fitting, and fit a suitable grommet or compression gland
(not included)
•Feed the mains cable into the luminaire, and fix the base to a suitable solid surface
•Wire for non-maintained operation (Fig. 2), maintained operation (Fig. 3) or switched-maintained
operation (Fig. 4) as required. Remove the link between LS and L if not required
Fig. 2 non-maintained
Fig. 3 maintained
Fig. 2 non-maintained
Fig. 3 maintained

GENERAL
WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the
product.
Installing in areas where the temperature consistently drops below 0°C may shorten the battery life.
This product is non-dimmable.
This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities
for where facilities exist.
The batteries in this luminaire are Nickel Cadmium and must be disposed of correctly. Please contact the local
authorities for the disposal of this toxic waste.
Fig. 4 switched-maintained
•Connect the battery to the battery connector on the PCB
•Slide the legend back into the fitting and refit the end cap
•Switch on and check for correct operation, ensuring the green indicator LED is illuminated
•We recommend, on commissioning the installation, a minimum charge period of 24 hours before
carrying out an emergency duration test
•If the batteries have been left in a discharged state for an extended period, we recommend that one or
more charge and discharge cycles are completed which should help to restore the battery capacity
WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
GENERAL
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the
product.
Installing in areas where the temperature consistently drops below 0°C may shorten the battery life.
This product is non-dimmable.
This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities
for where facilities exist.
The batteries in this luminaire are Nickel Cadmium and must be disposed of correctly. Please contact the local
authorities for the disposal of this toxic waste.
WARRANTY
This product has a warranty of 3 years (excluding battery) from date of purchase. Failure to install this product
in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the
batch code will invalidate the warranty. If this product should fail within its warranty period, it should be returned
to the place of purchase for a free of charge replacement. ML Accessories does not accept responsibility for
any installation costs associated with the replacement product. Your statutory rights are not affected. ML
Accessories reserve the right to alter product specification without prior notice.
TESTING FOR EMERGENCY LUMINAIRES
Recommended routine test procedure in accordance with BS5266
•Daily check – check LED charge indicator is illuminated
•Monthly functional test - simulate a mains supply failure for approx. 30 seconds by operation of key switch
or switching off circuit breaker. Ensure normal supply is restored after test and ensure charge indicator is
illuminated
•Annual three hour duration test - simulate a mains supply failure for three hour continuous test by operation
of key switch or switching off circuit breaker. Ensure normal supply is restored after test and ensure charge
indicator is illuminated
•If the luminaire fails any of the above tests, please contact a qualified electrician. See below for test record
sheet
Fig. 4 switched-maintained
• Connect the battery to the battery connector on the PCB
• Slide the legend back into the fitting and refit the end cap
• Switch on and check for correct operation, ensuring the green indicator LED is illuminated
• We recommend, on commissioning the installation, a minimum charge period of 24 hours before carrying
out an emergency duration test
• If the batteries have been left in a discharged state for an extended period, we recommend that one or more
charge and discharge cycles are completed which should help to restore the battery capacity

WARRANTY
This product has a warranty of 3 years (excluding battery) from date of purchase. Failure to install this product
in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal
of the batch code will invalidate the warranty. If this product should fail within its warranty period, it should
be returned to the place of purchase for a free of charge replacement. ML Accessories does not accept
responsibility for any installation costs associated with the replacement product. Your statutory rights are not
affected. ML Accessories reserve the right to alter product specification without prior notice.

Recommended routine test procedure in accordance with BS5266
• Daily check – check LED charge indicator is illuminated
• Monthly functional test - simulate a mains supply failure for approx. 30 seconds by operation of key switch
or switching off circuit breaker. Ensure normal supply is restored after test and ensure charge indicator is
illuminated
• Annual 3-hour duration test - simulate a mains supply failure for 3-hour continuous test by operation of key
switch or switching off circuit breaker. Ensure normal supply is restored after test and ensure charge indicator
is illuminated
• If the luminaire fails any of the above tests, please contact a qualified electrician. See below for test record
sheet
TESTING FOR EMERGENCY LUMINAIRES

230V 50Hz, IP20, Class 1, non-Dim, house, Ta 0~45
DCxxx21_V2

DCSEP21_V2
ML Accessories Limited LU5 4LT
www.mlaccessories.co.uk
54
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS
0~
45°C
TA