Eaton Crouse-Hinds Pauluhn DLLA M2 Series Setup guide

Pauluhn DLLA M2 Series Linear Emergency LED
Luminaire Fittings for Hazardous Locations
Installation & Maintenance Information
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
IF 1947
IF 1947 • 10/22 Copyright © 2022, Eaton’s Crouse-Hinds Division Page 1
APPLICATION
Pauluhn Linear Emergency LED luminaire are suitable for use in the following
hazardous (classied) locations as dened by the National Electrical Code
(NEC®):
The assembled luminaire shall be installed in accordance with the National
Electric Code NFPA70, and American Bureau of Shipping.
NEC
• Class I, Division 2, Groups A, B, C, D
• Class I, Zone 2
• Class II, Division 1, Groups E, F, G
• Class III
• Wet location, IP66/67, Type 4X
These luminaire housings shall be used with UL listed Crouse-Hinds hazard-
ous locations luminaire ttings namely LED Light Engine Cat Nos. DLLA*2 or
DLLA*4 series ending with M2 and Mounting means Cat Nos. M2-FLUSH-
MT-KIT, M2-CEILING-SWIVEL-KIT, M2-CEILING-WALL-KIT, M2-PM-KIT-1.25,
M2-PM-KIT-1.5, M2-PM-KIT-2.0, (refer to label provided inside the driver housing
for permissible tting details).
UL Standards:
• UL844 Hazardous (Classied)
• UL1598 Luminaires, UL1598A Marine
• UL8750
• UL924
CSA Standard:
• CSA C22.2 No. 250
• CSA C22.2 No. No.137
• CSA C22.2 No. No.141
Refer to the luminaire tting nameplate for specic classication information,
maximum ambient temperature suitability, and corresponding operating
temperature (T-code).
The assembled linear LED luminaire is designed for use indoors and outdoors
in marine and wet locations, where moisture, dirt, corrosion, vibration and
rough usage may be present.
INPUT VOLTAGE:
• UNV1: 120-277 VAC 50/60 Hz
1. Read carefully before installing and wiring luminaire and retain for future
reference.
2. Ensure area to be free of hazardous atmospheres before and during
installation and maintenance.
3. Do not use accessory equipment not recommended by manufacturer
may cause an unsafe condition.
4. Use only replacement parts from Eaton’s Crouse Hinds division.
5. To avoid the risk of re, explosion or electric shock, this product should
be installed, inspected and maintained by a qualied electrician only, in
accordance with all applicable electrical codes.
6. Do not use this equipment for other than intended use.
7. Replace entire battery unit and LED driver when necessary. Contact the
manufacturer for information on service.
8. Do not attempt to service battery.
9. See product label for minimum supply wire temperature rating.
10. Battery requires 24hrs to fully charge. Allow 24 hours charging time
before depending on the battery to operate at full capacity.
11. The emergency battery requires a minimum charge time of one (1) hour
before testing the circuit, 24 hours is required for a full charge.
12. Equipment should be mounted in locations and at heights where it will
not readily be subjected to tampering by unauthorized personnel. Max.
mounting height: 25.2 feet)
13. The emergency luminaire is intended to be installed with CG-256 (issued
by the American Bureau of Shipping and Coast Guard.
14. This product must be installed in accordance with the applicable installa-
tion code by a person familiar with the construction and operation of the
product and the hazards involved.
IMPORTANT SAFEGUARDS - READ AND FOLLOW ALL SAFETY INSTRUCTIONS
STORAGE INSTRUCTIONS
1. EM luminaire must be stored in an ambient temperature range of 0°C
to 40°C.
2. Battery should be charged and discharged within 6 months. At a
minimum, the battery should be recharged within this time.
WARNING
To avoid electric shock:
Be certain electrical power is OFF before and during installation and
maintenance.
Luminaire must be supplied by a wiring system with an equipment
grounding conductor in accordance to the NEC and CEC for the specific
Hazardous Locations involved.
To avoid burning hands:
Make sure lens and housing are cool when performing maintenance.
!
WARNING
To avoid explosion:
Make sure the supply voltage is the same as the luminaire voltage.
Do not install where the marked operating temperatures exceed the
ignition temperature of the hazardous atmosphere.
Do not operate in ambient temperatures above those indicated on the
luminaire nameplate.
Use proper supply wiring as specified on the luminaire nameplate.
All gasket seals must be clean and undamaged.
Before opening, electrical power to the luminaire must be turned off.
Keep tightly closed when in operation.
To reduce the risk of ignition due to electrostatic discharge, avoid contact
with the luminaire while explosive atmosphere is present. Clean only with
damp cloth.
!

IF 1947 • 10/22 Copyright © 2022, Eaton’s Crouse-Hinds Division Page 2
INSTALLATION
A. M2-FLUSH-MT-KIT
1. Make sure the power is disconnected to the conduit system before
installing the luminaire.
2. Install ush mount brackets to rear of luminaire driver housing using
the provided two (2) 1/4” hex bolts and split ring lock washers for each
bracket. Bracket orientation as shown in Figure 1. Torque to 64 in.-lbs (7.2
N-m)
3. Identify mounting location suitable for supporting luminaire, mark and drill
holes for ush brackets per dimensions shown in Figure 1.
4. Luminaire is now ready for mounting. It is strongly suggested to use
two (2) qualied tradespeople to proceed with the nal mounting of the
luminaire. This is recommended to avoid any personal injury or damage to
the luminaire.
5. Install and tighten four (4) 1/4” diameter fasteners (customer supplied) in
bracket mounting holes. It is recommended that stainless steel hardware
be used in locations with corrosion concerns.
Figure 1. Flush Ceiling Mount Installation
Length 2 Foot
(in)
2 Foot
(mm)
4 Foot
(in)
4 Foot
(mm)
A 24.0 610 39.0 991
B 24.25 616 24.25 616
C 2.50 63.5 2.50 63.5
THIRD ANGLE PROJECTION
B
C
A
660
26.0
A
123.2
4.85
175.3
6.90
1/4-20 x 1/2" HEX HEAD BOLT
1/2" SPLIT LOCK WASHER
ZONE NO. DESCRIPTION DATE APPRD. LTR. NO.
CCHSY-SW-Template-D
SW_REV 11/2015
DO NOT SCALE DRAWING
NOTES:
1.
A
B
C
D
12
3
4
5
6
7
8
A
D
C
B
8765432 1
Your name
ASSY2 CAT2
CAT1 ASSY1
ARE IN
MILLIMETERS.
DIMENSIONS IN [ ] ARE IN
ALL PRIMARY DIMENSIONS
UNLESS OTHERWISE SPECIFIED,
MM/DD/YYYY
Your Name
WITH ASME Y14.5 2009.
DIM AND TOL IN ACCORDANCE
±
±
±
±
.1 .3
INCHES.
rev
0000000
WT. 15.84 LB
SCALE 1:2
FIRST MADE FOR Catalog Family
Title Line 1
APPROVED BY
DRAWN BY
Finish
... THICK
Material
mm in.
.13
.000
1.5
Your Name
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
AND IS TO BE RETURNED UPON REQUEST.
Title Line 2
Your Name
MM/DD/YYYY
1.5
±
.005
±
.01
±
±
ANGLES
.XXX
.XX
.X
REDRAWN DATE
ORIGINAL DATE
UNLESS OTHERWISE SPECIFIED
TOLERANCES
MATERIAL:
FINISH:
APPROVED BY
CHECKED BY
USED ON
APPLICATION
NEXT ASSY.
TITLE
CODE IDENT. NO.
SIZE
REV.
D
SHEET 1 OF 5
CODE ...
THIRD ANGLE PROJECTION
B
C
A
660
26.0
A
123.2
4.85
175.3
6.90
1/4-20 x 1/2" HEX HEAD BOLT
1/2" SPLIT LOCK WASHER
ZONE NO. DESCRIPTION DATE APPRD. LTR. NO.
CCHSY-SW-Template-D
SW_REV 11/2015
DO NOT SCALE DRAWING
NOTES:
1.
A
B
C
D
12
3
4
5
6
7
8
A
D
C
B
8765432 1
Your name
ASSY2 CAT2
CAT1 ASSY1
ARE IN
MILLIMETERS.
DIMENSIONS IN [ ] ARE IN
ALL PRIMARY DIMENSIONS
UNLESS OTHERWISE SPECIFIED,
MM/DD/YYYY
Your Name
WITH ASME Y14.5 2009.
DIM AND TOL IN ACCORDANCE
±
±
±
±
.1 .3
INCHES.
rev
0000000
WT. 15.84 LB
SCALE 1:2
FIRST MADE FOR Catalog Family
Title Line 1
APPROVED BY
DRAWN BY
Finish
... THICK
Material
mm in.
.13
.000
1.5
Your Name
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
AND IS TO BE RETURNED UPON REQUEST.
Title Line 2
Your Name
MM/DD/YYYY
1.5
±
.005
±
.01
±
±
ANGLES
.XXX
.XX
.X
REDRAWN DATE
ORIGINAL DATE
UNLESS OTHERWISE SPECIFIED
TOLERANCES
MATERIAL:
FINISH:
APPROVED BY
CHECKED BY
USED ON
APPLICATION
NEXT ASSY.
TITLE
CODE IDENT. NO.
SIZE
REV.
D
SHEET 1 OF 5
CODE ...
INSTALLATION
Max. mounting height of 25.2 ft (7.68m)
B. M2-CEILING-WALL-KT
1. Make sure the power is disconnected to the conduit system before
installing the luminaire.
2. Mark and drill holes for fastening end brackets. Use two (2) 1/4” diameter
fasteners (customer supplied) at center to center measurements (see
Figure 2). It is recommended that stainless steel hardware be used in
locations with corrosion concerns.
3. Luminaire is now ready for mounting. It is strongly suggested to use
two (2) qualied tradespeople to proceed with the nal mounting of the
luminaire. This is recommended to avoid any personal injury or damage to
the luminaire.
4. For end mount wall/ceiling mounting brackets, it is recommended to
mount one bracket rst and then, while supporting the luminaire, insert it
into the mounted bracket, then attach the other bracket.
5. Aim the luminaire to achieve desired light output and tighten the 1/4” set
screws on brackets. Torque to 64 in.-lbs. (7.2 N-m).
6. Use set screw to limit rotation of the luminaire.
Figure 2. Ceiling-Wall Mount Installation
Length 2 Foot
(in)
2 Foot
(mm)
4 Foot
(in)
4 Foot
(mm)
A 28.5 724 28.5 724
B 24.0 610 39.0 991
THIRD ANGLE PROJECTION
A
B
175.3
6.90
205.2
8.08
63.5
2.50
54
2.13
B
723
28.5
CCHSY-SW-Template-D
SW_REV 11/2015
DO NOT SCALE DRAWING
NOTES:
1.
A
B
C
D
12
3
4
5
6
7
8
A
D
C
B
8765432 1
Your name
ASSY2 CAT2
CAT1 ASSY1
ARE IN
MILLIMETERS.
DIMENSIONS IN [ ] ARE IN
ALL PRIMARY DIMENSIONS
UNLESS OTHERWISE SPECIFIED,
MM/DD/YYYY
Your Name
WITH ASME Y14.5 2009.
DIM AND TOL IN ACCORDANCE
±
±
±
±
.1 .3
INCHES.
rev
0000000
WT. 15.84 LB
SCALE 1:2
FIRST MADE FOR Catalog Family
Title Line 1
APPROVED BY
DRAWN BY
Finish
... THICK
Material
mm in.
.13
.000
1.5
Your Name
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
AND IS TO BE RETURNED UPON REQUEST.
Title Line 2
Your Name
MM/DD/YYYY
1.5
±
.005
±
.01
±
±
ANGLES
.XXX
.XX
.X
REDRAWN DATE
ORIGINAL DATE
UNLESS OTHERWISE SPECIFIED
TOLERANCES
MATERIAL:
FINISH:
APPROVED BY
CHECKED BY
USED ON
APPLICATION
NEXT ASSY.
TITLE
CODE IDENT. NO.
SIZE
REV.
D
SHEET 2 OF 5
CODE ...
!
WARNING
To avoid injury to personnel, do not let the luminaire hang or ex on one
bracket at a time. Failing to comply will result in breakage of bracket and
possible injury or death.
!
WARNING
To avoid injury to personnel, do not let the luminaire hang or ex on one
bracket at a time. Failing to comply will result in breakage of bracket and
possible injury or death.

C. M2-CEILING-SWIVEL-KIT
1. Make sure the power is disconnected to the conduit system before
installing the luminaire.
2. Identify mounting location suitable for supporting the luminaire, mark and
drill holes for fastening swivel brackets per center-to-center dimension ‘A’
in table below (see Figure 3).
3. Mount swivel bracket assemblies to luminaire driver housing as shown
in Figure 3. Use two (2) of the provided 1/4” hex bolts and split ring lock
washers for each bracket. Torque to 64 in-lb (7.2 N-m).
4. Luminaire is now ready for mounting. It is strongly suggested to use
two (2) qualied tradespeople to proceed with the nal mounting of the
luminaire. This is recommended to avoid any personal injury or damage to
the luminaire.
5. Install and tighten 1/4” diameter fasteners (customer supplied) in each
of the bracket mounting holes. It is recommended that stainless steel
hardware be used in locations with corrosion concerns.
6. Adjust the position of the luminaire to the desired angle and tighten the
two (2) 5/16” pivot bolts snugly to the bracket and then tighten hex nuts.
Torque to 120 in.-lbs. (13.6 N-m).
IF 1947 • 10/22 Copyright © 2022, Eaton’s Crouse-Hinds Division Page 3
Length 2 Foot
(in)
2 Foot
(mm)
4 Foot
(in)
4 Foot
(mm)
A 26.4 670 26.4 670
B 24.0 610 39.0 991
Figure 3. Ceiling-Swivel Mount Installation
THIRD ANGLE PROJECTION
166.9
6.57
175.3
6.90
A
B
B
669.3
26.35
1/4" SPLIT LOCK WASHER
1/4-20 x 1/2" CAP SCREW
CCHSY-SW-Template-D
SW_REV 11/2015
DO NOT SCALE DRAWING
NOTES:
1.
A
B
C
D
12
3
4
5
6
7
8
A
D
C
B
8765432 1
Your name
ASSY2 CAT2
CAT1 ASSY1
ARE IN
MILLIMETERS.
DIMENSIONS IN [ ] ARE IN
ALL PRIMARY DIMENSIONS
UNLESS OTHERWISE SPECIFIED,
MM/DD/YYYY
Your Name
WITH ASME Y14.5 2009.
DIM AND TOL IN ACCORDANCE
±
±
±
±
.1 .3
INCHES.
rev
0000000
WT. 15.84 LB
SCALE 1:2
FIRST MADE FOR Catalog Family
Title Line 1
APPROVED BY
DRAWN BY
Finish
... THICK
Material
mm in.
.13
.000
1.5
Your Name
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
AND IS TO BE RETURNED UPON REQUEST.
Title Line 2
Your Name
MM/DD/YYYY
1.5
±
.005
±
.01
±
±
ANGLES
.XXX
.XX
.X
REDRAWN DATE
ORIGINAL DATE
UNLESS OTHERWISE SPECIFIED
TOLERANCES
MATERIAL:
FINISH:
APPROVED BY
CHECKED BY
USED ON
APPLICATION
NEXT ASSY.
TITLE
CODE IDENT. NO.
SIZE
REV.
D
SHEET 3 OF 5
CODE ...
THIRD ANGLE PROJECTION
166.9
6.57
175.3
6.90
A
B
B
669.3
26.35
1/4" SPLIT LOCK WASHER
1/4-20 x 1/2" CAP SCREW
CCHSY-SW-Template-D
SW_REV 11/2015
DO NOT SCALE DRAWING
NOTES:
1.
A
B
C
D
12
3
4
5
6
7
8
A
D
C
B
8765432 1
Your name
ASSY2 CAT2
CAT1 ASSY1
ARE IN
MILLIMETERS.
DIMENSIONS IN [ ] ARE IN
ALL PRIMARY DIMENSIONS
UNLESS OTHERWISE SPECIFIED,
MM/DD/YYYY
Your Name
WITH ASME Y14.5 2009.
DIM AND TOL IN ACCORDANCE
±
±
±
±
.1 .3
INCHES.
rev
0000000
WT. 15.84 LB
SCALE 1:2
FIRST MADE FOR Catalog Family
Title Line 1
APPROVED BY
DRAWN BY
Finish
... THICK
Material
mm in.
.13
.000
1.5
Your Name
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
AND IS TO BE RETURNED UPON REQUEST.
Title Line 2
Your Name
MM/DD/YYYY
1.5
±
.005
±
.01
±
±
ANGLES
.XXX
.XX
.X
REDRAWN DATE
ORIGINAL DATE
UNLESS OTHERWISE SPECIFIED
TOLERANCES
MATERIAL:
FINISH:
APPROVED BY
CHECKED BY
USED ON
APPLICATION
NEXT ASSY.
TITLE
CODE IDENT. NO.
SIZE
REV.
D
SHEET 3 OF 5
CODE ...
D. M2-PM-KIT-*
1. Make sure the power is disconnected to the conduit system before
installing the luminaire.
2. Verify that the clamp internal diameter is consistent with the diameter of
the pole prior to installation. Clamps are available in 1.65 (42mm), 2.00
(51mm) and 2.36 (60mm) sizes (see Figure 5).
3. Pole mount brackets are spaced 20.75” on the bracket centerlines as
shown in Figure 4.
4. Tighten two (2) of the provided 1/4” hex bolts and split ring lock washers
on each bracket sub-assembly. Torque to 64 in-lbs (7.2 N-m).
5. Remove the two (2) 5/16” screws, lock washers and nuts on each clamp
and remove the upper clamp halves.
6. Luminaire is now ready for mounting. It is strongly suggested to use
two (2) qualied tradespeople to proceed with the nal mounting of the
luminaire. This is recommended to avoid any personal injury or damage to
the luminaire.
7. Lift luminaire into position such that the pole ts into the lower clamp
halves.
8. Install the two (2) upper clamp halves and the 5/16” screws, lock washers
and nuts on each clamp.
9. Tighten the nuts on the 5/16” screws evenly using a back and forth
sequence. Torque to 120 in.-lbs. (13.6 N-m).
Cat. # Conguration
Dimension (inches)
A B C D
M2-PM-KIT-1.25 PM Kit 2.0 (trade
size 2”) 4.331 3.543 2.36 1.693
M2-PM-KIT-1.5 PM Kit 1.5 (trade
size 1 - 1/2”) 3.740 2.953 2.00 1.535
M2-PM-KIT-2.0 PM Kit 1.25 (trade
size 1 - 1/14”) 3.386 2.598 1.65 1.378
Length 2 Foot
(in)
2 Foot
(mm)
4 Foot
(in)
4 Foot
(mm)
A 24.0 610 39.0 991
B See table below for pipe clamp diameters
Figure 4. Pole Mount Installation
Figure 5. Pole Mount Details
THIRD ANGLE PROJECTION
A
527.1
20.75
A
171
6.7
B
175.3
6.90
198
7.8
A
C
D
B
CCHSY-SW-Template-D
SW_REV 11/2015
DO NOT SCALE DRAWING
NOTES:
1.
A
B
C
D
12
3
4
5
6
7
8
A
D
C
B
8765432 1
Your name
ASSY2 CAT2
CAT1 ASSY1
ARE IN
MILLIMETERS.
DIMENSIONS IN [ ] ARE IN
ALL PRIMARY DIMENSIONS
UNLESS OTHERWISE SPECIFIED,
MM/DD/YYYY
Your Name
WITH ASME Y14.5 2009.
DIM AND TOL IN ACCORDANCE
±
±
±
±
.1 .3
INCHES.
rev
0000000
WT. 15.84 LB
SCALE 1:2
FIRST MADE FOR Catalog Family
Title Line 1
APPROVED BY
DRAWN BY
Finish
... THICK
Material
mm in.
.13
.000
1.5
Your Name
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
AND IS TO BE RETURNED UPON REQUEST.
Title Line 2
Your Name
MM/DD/YYYY
1.5
±
.005
±
.01
±
±
ANGLES
.XXX
.XX
.X
REDRAWN DATE
ORIGINAL DATE
UNLESS OTHERWISE SPECIFIED
TOLERANCES
MATERIAL:
FINISH:
APPROVED BY
CHECKED BY
USED ON
APPLICATION
NEXT ASSY.
TITLE
CODE IDENT. NO.
SIZE
REV.
D
SHEET 4 OF 5
CODE ...
THIRD ANGLE PROJECTION
A
527.1
20.75
A
171
6.7
B
175.3
6.90
198
7.8
A
C
D
B
CCHSY-SW-Template-D
SW_REV 11/2015
DO NOT SCALE DRAWING
NOTES:
1.
A
B
C
D
12
3
4
5
6
7
8
A
D
C
B
8765432 1
Your name
ASSY2 CAT2
CAT1 ASSY1
ARE IN
MILLIMETERS.
DIMENSIONS IN [ ] ARE IN
ALL PRIMARY DIMENSIONS
UNLESS OTHERWISE SPECIFIED,
MM/DD/YYYY
Your Name
WITH ASME Y14.5 2009.
DIM AND TOL IN ACCORDANCE
±
±
±
±
.1 .3
INCHES.
rev
0000000
WT. 15.84 LB
SCALE 1:2
FIRST MADE FOR Catalog Family
Title Line 1
APPROVED BY
DRAWN BY
Finish
... THICK
Material
mm in.
.13
.000
1.5
Your Name
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
AND IS TO BE RETURNED UPON REQUEST.
Title Line 2
Your Name
MM/DD/YYYY
1.5
±
.005
±
.01
±
±
ANGLES
.XXX
.XX
.X
REDRAWN DATE
ORIGINAL DATE
UNLESS OTHERWISE SPECIFIED
TOLERANCES
MATERIAL:
FINISH:
APPROVED BY
CHECKED BY
USED ON
APPLICATION
NEXT ASSY.
TITLE
CODE IDENT. NO.
SIZE
REV.
D
SHEET 4 OF 5
CODE ...
THIRD ANGLE PROJECTION
A
527.1
20.75
A
171
6.7
B
175.3
6.90
198
7.8
A
C
D
B
CCHSY-SW-Template-D
SW_REV 11/2015
DO NOT SCALE DRAWING
NOTES:
1.
A
B
C
D
12
3
4
5
6
7
8
A
D
C
B
8765432 1
Your name
ASSY2 CAT2
CAT1 ASSY1
ARE IN
MILLIMETERS.
DIMENSIONS IN [ ] ARE IN
ALL PRIMARY DIMENSIONS
UNLESS OTHERWISE SPECIFIED,
MM/DD/YYYY
Your Name
WITH ASME Y14.5 2009.
DIM AND TOL IN ACCORDANCE
±
±
±
±
.1 .3
INCHES.
rev
0000000
WT. 15.84 LB
SCALE 1:2
FIRST MADE FOR Catalog Family
Title Line 1
APPROVED BY
DRAWN BY
Finish
... THICK
Material
mm in.
.13
.000
1.5
Your Name
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
AND IS TO BE RETURNED UPON REQUEST.
Title Line 2
Your Name
MM/DD/YYYY
1.5
±
.005
±
.01
±
±
ANGLES
.XXX
.XX
.X
REDRAWN DATE
ORIGINAL DATE
UNLESS OTHERWISE SPECIFIED
TOLERANCES
MATERIAL:
FINISH:
APPROVED BY
CHECKED BY
USED ON
APPLICATION
NEXT ASSY.
TITLE
CODE IDENT. NO.
SIZE
REV.
D
SHEET 4 OF 5
CODE ...
!
WARNING
To avoid injury to personnel, do not let the luminaire hang or ex on one
bracket at a time. Failing to comply will result in breakage of bracket and
possible injury or death.
!
WARNING
To avoid injury to personnel, do not let the luminaire hang or ex on one
bracket at a time. Failing to comply will result in breakage of bracket and
possible injury or death.

IF 1947 • 10/22 Copyright © 2022, Eaton’s Crouse-Hinds Division Page 4
E. PENDANT MOUNT INSTRUCTIONS
1. Make sure the power is disconnected from the conduit system before
installing the luminaire
2. For Pendant Mount the conduit should be located in line with the 3/4”
NPT entry on the rear of the luminaire driver housing (see Figure 6).
3. Luminaire is ready for mounting. It is strongly suggested to use two (2)
qualied tradespeople to proceed with the nal mounting of the luminaire.
This is recommended to avoid any personal injury or damage to the
luminaire.
4. Verify sufcient quantity of Eaton’s STL thread lubricant is on conduit
entries and that all unused conduit entries on the end caps are closed
with lubricated plugs (see Figure 13).
5. Engage threaded conduit in rear driver housing NPT entry and fully tighten
in to desired position for operations (engage at least 3-1/2 threads).
6. Tighten set screws on driver housing as shown in Figure 8. Torque set
screws to 20 in-lb (2.3 N-m).
7. Luminaire now ready to make electrical connections. See section titled
Wiring The LED Luminaire for detailed instructions.
Length 2 Foot
(in)
2 Foot
(mm)
4 Foot
(in)
4 Foot
(mm)
A 24.0 610 39.0 991
Figure 6. Pendant Mount Detail View
Figure 7. Pendant Mount Set Screw Detail
THIRD ANGLE PROJECTION
A
THREADED CONDUIT
(3/4" NPT STANDARD)
175.3
6.90
112.9
4.45
CCHSY-SW-Template-D
SW_REV 11/2015
DO NOT SCALE DRAWING
NOTES:
1.
A
B
C
D
12
3
4
5
6
7
8
A
D
C
B
8765432 1
Your name
ASSY2 CAT2
CAT1 ASSY1
ARE IN
MILLIMETERS.
DIMENSIONS IN [ ] ARE IN
ALL PRIMARY DIMENSIONS
UNLESS OTHERWISE SPECIFIED,
MM/DD/YYYY
Your Name
WITH ASME Y14.5 2009.
DIM AND TOL IN ACCORDANCE
±
±
±
±
.1 .3
INCHES.
rev
0000000
WT. 15.84 LB
SCALE 1:2
FIRST MADE FOR Catalog Family
Title Line 1
APPROVED BY
DRAWN BY
Finish
... THICK
Material
mm in.
.13
.000
1.5
Your Name
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
AND IS TO BE RETURNED UPON REQUEST.
Title Line 2
Your Name
MM/DD/YYYY
1.5
±
.005
±
.01
±
±
ANGLES
.XXX
.XX
.X
REDRAWN DATE
ORIGINAL DATE
UNLESS OTHERWISE SPECIFIED
TOLERANCES
MATERIAL:
FINISH:
APPROVED BY
CHECKED BY
USED ON
APPLICATION
NEXT ASSY.
TITLE
CODE IDENT. NO.
SIZE
REV.
D
SHEET 5 OF 5
CODE ...
THIRD ANGLE PROJECTION
A
THREADED CONDUIT
(3/4" NPT STANDARD)
175.3
6.90
112.9
4.45
CCHSY-SW-Template-D
SW_REV 11/2015
DO NOT SCALE DRAWING
NOTES:
1.
A
B
C
D
12
3
4
5
6
7
8
A
D
C
B
8765432 1
Your name
ASSY2 CAT2
CAT1 ASSY1
ARE IN
MILLIMETERS.
DIMENSIONS IN [ ] ARE IN
ALL PRIMARY DIMENSIONS
UNLESS OTHERWISE SPECIFIED,
MM/DD/YYYY
Your Name
WITH ASME Y14.5 2009.
DIM AND TOL IN ACCORDANCE
±
±
±
±
.1 .3
INCHES.
rev
0000000
WT. 15.84 LB
SCALE 1:2
FIRST MADE FOR Catalog Family
Title Line 1
APPROVED BY
DRAWN BY
Finish
... THICK
Material
mm in.
.13
.000
1.5
Your Name
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
AND IS TO BE RETURNED UPON REQUEST.
Title Line 2
Your Name
MM/DD/YYYY
1.5
±
.005
±
.01
±
±
ANGLES
.XXX
.XX
.X
REDRAWN DATE
ORIGINAL DATE
UNLESS OTHERWISE SPECIFIED
TOLERANCES
MATERIAL:
FINISH:
APPROVED BY
CHECKED BY
USED ON
APPLICATION
NEXT ASSY.
TITLE
CODE IDENT. NO.
SIZE
REV.
D
SHEET 5 OF 5
CODE ...
SECONDARY SUPPORT
If using secondary support, attach one end of the support cable to one of the
four (4) attachment points provided on the luminaire driver housing and secure
the other end to a xed support. Use a minimum of two (2) support cables per
luminaire, securing a single cable at two (2) locations on the exterior of the
luminaire driver housing.
Arrange the secondary support cables to limit the suspended vertical distance
to no more than 18 inches from the primary mounted position. Cables must
be installed in this manner to limit the potential vertical drop to 18 inches
maximum.
PUSH-TO-TEST SWITCH
A remote push-to-test switch (not supplied) suitable for the classied area
must be wired in the supply circuit to periodically test the emergency operation
feature (see wiring diagrams). The switch used must be suitable for the area
classications.
STATUS INDICATOR LIGHT
The status indicator light located on LED board (Red LED) will be “ON“
when the battery is charging. If the status LED is ashing, replace
emergency driver unit.. If required customer can remote mount their own
status indicator light with suitable electrical ratings. Contact Eaton’s
Crouse-Hinds for additional support.
For remote mounting of Status Indicator light refer to gure below “Remote
mounting Test switch & Status indicator”.
Important instructions for remote mounting of push to test switch (customer
supplied):
a. Switch shall be installed using acceptable wiring methods for the areas
involved in accordance with the NEC.
b. Switch shall be connected to the emergency luminaire circuit such that
when depressed it provides a transfer function and disconnects and
isolates the normal input from the emergency input.
c. Switch shall be identied as to its function (i.e. – marked “Emergency
Luminaire Test Switch”).
d. Switch shall have electrical ratings suitable for the emergency luminaires.
e. Switch shall be manually operated type.
f. Switch shall be of Momentary-contact type.
g. Switch must be visible and accessible without the use of tools.
Figure 8 Remote mounting test switch and status indicator
EMERGENCY DRIVER UNIT INFORMATION
Pauluhn Emergency Linear LED luminaires are supplied with an emergency
driver unit. Disconnect the battery converter connector (Red-Red wires)
prior to performing maintenance (Refer to Figures 14A, 14B or 14C). This will
disconnect the charged battery from the LEDs. The emergency driver unit must
be checked periodically to ensure that it is working properly.
IMPORTANT INSTRUCTIONS (for customer supplied wall switch)
1. Installations in which a remote wall switch is to be used, connect an
unswitched supply line to the Black wire (L) and a switched supply line to
the White/Red wire (L1) of the Emergency Backup Module. Refer to wall
switch connection details on Wiring Diagrams in Figures 14A, 14B and
14C.
2. When the switched supply line (L1) is de-energized using the wall switch,
the luminaire will turn off light output while the battery circuit remains
active and charging.
3. Upon the loss of line power to the Emergency BackupModule, the
luminaire will immediately operate in Emergency Operations mode
(automatic switching) with a reduced light output .
4. If the unswitched supply line is connected to Black wire (L) only, battery
will charge, and luminaire will be in OFF condition (i.e AC driver is not in
operating condition). This is the Emergency Operations Only mode and
the luminaire shall only be illuminated on the loss of the line power.
5. If a wall switch is to be installed in a hazardous (classied) area, the switch
used must be rated for the area classication.
6. The wall switch used shall be suitable for 120 - 277VAC and ≥15A
operations.
Threaded conduit - 3/4" NPT
standard (not provided by
Eaton’s Crouse-Hinds)

WIRINGTHE LED LUMINAIRE
1. Assembly sequence is common to both the DLLA2 and DLLA4 LED
luminaire products. The DLLA2 luminaire is used in the supporting
illustrations.
2. To gain access to the luminaire input wiring connections loosen the eight
(8) #10-32 x .75” stainless steel cover screws (see Figure 9) until screws
are free from driver housing. Screws are a captive type and should not be
fully removed from the light engine tting assembly.
3. Pull the retention clips on the light engine assembly to free it from the
driver housing and pivot the light engine tting on the driver housing
service hooks (see Figure 10). This shall expose the internal volume of the
driver housing and the input wiring terminal carriers.
4. Connections to the LED light engine and LED driver are pre-wired and
do not require any further processing. Route the Line, Neutral and
Ground input wires to the wire terminal carrier (see Figure 11) and make
connections per system wiring diagrams (see Figures 14A, 14B and
14C) using methods that comply with all applicable codes. Terminate the
equipment grounding connector (green) rst, the common (white) next,
and nally, the line voltage (black). Ensure all electrical connections have
been completed and terminal block lever locks are fully seated and secure.
Note- standard entries in driver housing and 3/4” NPT thread.
5. Connect module battery connections (white wires) as the battery is
shipped disconnected to prevent discharging.
6. Connect Emergency Backup Module converter connection (Red wires) as
the last electrical connection. This connection enables electrical function in
the backup module and failure to make this connection will result in non-
function of the luminaire.
7. To connect remote test switch (customer supplied) locate the brown and
purple leads from the emergency backup driver and connect remote test
switch wires using 3-pole wire terminals provided (see wiring diagram).
8. If using the dimming function of the LED driver, use only wires rated to
600V minimum. Dimming circuit operates on 0-10 VDC; dimmer shall be
suitably certied for the intended installation environment (e.g. Hazardous,
Ordinary Locations, etc...).
9. Re-install the light engine tting and tighten all eight (8) cover mounting
screws 23 in.-lbs. (2.6 N-m) using the bolting sequence directed in Figure
9. Verify that no luminaire wiring is pinched or trapped between light
engine and driver housing. Start all screws prior to tightening.
10. Replace any damaged or missing cover screws. Consult factory for
replacement parts.
WIRING INSTALLATION CHECKLIST
1. Verify sufcient quantity of Eaton’s STL thread lubricant is on conduit
entries and that all unused conduit entries on the end caps are closed
with lubricated plugs (see Figure 13).
2. Verify conduit is installed to at least ve (5) full threads into the end cap
conduit entries. Recommend approximately 1/8” bead quantity of Eaton’s
STL thread lubricant on conduit entries.
3. Verify installed conduit is torqued to 42-52 ft.-lbs. (57-71 N-m) for 3/4”
plug.
4. Verify supply wires are connected to luminaire wire leads per Figure 14A,
Figure 14B or Figure 14C.
5. Verify all electrical connections are properly made and secure.
6. Verify all wires are routed correctly and are fully contained in the driver
housing without any wires being pinched when the light engine tting
is rotated back into position. Re-attach driver cover to luminaire driver
housing using the bolt tightening sequence in Figure 9.
7. Verify captive attachment screws are tightened to 23 in.-lbs. (2.6 N-m) and
light engine tting is in ush contact with driver housing.
IF 1947 • 10/22 Copyright © 2022, Eaton’s Crouse-Hinds Division Page 5
Figure 13. NPT Fitting
Figure 9. Driver Housing Screw Locations
Figure 10. Light Engine Rotated for Servicing
Figure 11. Input WiringTerminal Carrier
Figure 12. Driver Housing Safety Cable Mounting Locations
NOTE
A maximum of 8 luminaires may be daisy chained on a single circuit. See
luminaire wiring diagrams.
THIRD ANGLE PROJECTION
CCHSY-SW-Template-D
SW_REV 11/2015
DO NOT SCALE DRAWING
NOTES:
1.
A
B
C
D
12
3
4
5
6
7
8
A
D
C
B
8765432 1
Your name
ASSY2 CAT2
CAT1 ASSY1
ARE IN
MILLIMETERS.
DIMENSIONS IN [ ] ARE IN
ALL PRIMARY DIMENSIONS
UNLESS OTHERWISE SPECIFIED,
MM/DD/YYYY
Your Name
WITH ASME Y14.5 2009.
DIM AND TOL IN ACCORDANCE
±
±
±
±
.1 .3
INCHES.
rev
0000000
WT. 15.85 LB
SCALE 2:3
FIRST MADE FOR Catalog Family
Title Line 1
APPROVED BY
DRAWN BY
Finish
... THICK
Material
mm in.
.13
.000
1.5
Your Name
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
AND IS TO BE RETURNED UPON REQUEST.
Title Line 2
Your Name
MM/DD/YYYY
1.5
±
.005
±
.01
±
±
ANGLES
.XXX
.XX
.X
REDRAWN DATE
ORIGINAL DATE
UNLESS OTHERWISE SPECIFIED
TOLERANCES
MATERIAL:
FINISH:
APPROVED BY
CHECKED BY
USED ON
APPLICATION
NEXT ASSY.
TITLE
CODE IDENT. NO.
SIZE
REV.
D
SHEET 6 OF 6
CODE ...
5
6
7
824
31
THIRD ANGLE PROJECTION
CCHSY-SW-Template-D
SW_REV 11/2015
DO NOT SCALE DRAWING
NOTES:
1.
A
B
C
D
12
3
4
5
6
7
8
A
D
C
B
8765432 1
Your name
ASSY2 CAT2
CAT1 ASSY1
ARE IN
MILLIMETERS.
DIMENSIONS IN [ ] ARE IN
ALL PRIMARY DIMENSIONS
UNLESS OTHERWISE SPECIFIED,
MM/DD/YYYY
Your Name
WITH ASME Y14.5 2009.
DIM AND TOL IN ACCORDANCE
±
±
±
±
.1 .3
INCHES.
rev
0000000
WT. 15.85 LB
SCALE 2:3
FIRST MADE FOR Catalog Family
Title Line 1
APPROVED BY
DRAWN BY
Finish
... THICK
Material
mm in.
.13
.000
1.5
Your Name
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
AND IS TO BE RETURNED UPON REQUEST.
Title Line 2
Your Name
MM/DD/YYYY
1.5
±
.005
±
.01
±
±
ANGLES
.XXX
.XX
.X
REDRAWN DATE
ORIGINAL DATE
UNLESS OTHERWISE SPECIFIED
TOLERANCES
MATERIAL:
FINISH:
APPROVED BY
CHECKED BY
USED ON
APPLICATION
NEXT ASSY.
TITLE
CODE IDENT. NO.
SIZE
REV.
D
SHEET 6 OF 6
CODE ...
THIRD ANGLE PROJECTION
CCHSY-SW-Template-D
SW_REV 11/2015
DO NOT SCALE DRAWING
NOTES:
1.
A
B
C
D
12
3
4
5
6
7
8
A
D
C
B
8765432 1
Your name
ASSY2 CAT2
CAT1 ASSY1
ARE IN
MILLIMETERS.
DIMENSIONS IN [ ] ARE IN
ALL PRIMARY DIMENSIONS
UNLESS OTHERWISE SPECIFIED,
MM/DD/YYYY
Your Name
WITH ASME Y14.5 2009.
DIM AND TOL IN ACCORDANCE
±
±
±
±
.1 .3
INCHES.
rev
0000000
WT. 15.59 LB
SCALE 1:1
FIRST MADE FOR Catalog Family
Title Line 1
APPROVED BY
DRAWN BY
Finish
... THICK
Material
mm in.
.13
.000
1.5
Your Name
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
AND IS TO BE RETURNED UPON REQUEST.
Title Line 2
Your Name
MM/DD/YYYY
1.5
±
.005
±
.01
±
±
ANGLES
.XXX
.XX
.X
REDRAWN DATE
ORIGINAL DATE
UNLESS OTHERWISE SPECIFIED
TOLERANCES
MATERIAL:
FINISH:
APPROVED BY
CHECKED BY
USED ON
APPLICATION
NEXT ASSY.
TITLE
CODE IDENT. NO.
SIZE
REV.
D
SHEET 7 OF 7
CODE ...

Figure 14A. 2 Foot UNV1 Standard Wiring Diagram
Figure 14B. 4 Foot UNV1 StandardWiring Diagram
WIRING DIAGRAMS
IF 1947 • 10/22 Copyright © 2022, Eaton’s Crouse-Hinds Division Page 6

MAINTENANCE GENERAL
Important Notes: Branch circuit eld wiring must be disconnected prior
to initial luminaire installation or maintenance. Before performing any
maintenance work with the luminaire enclosure open, the battery pack
must be disconnected from the converter/inverter assembly by separating
the latching connectors (connecting two white wires and two black and
red wires of battery). Also disconnect battery/converter connector (Red-
Red wires). See Figures 14A, 14B and 14C for connection location.
1. Disconnect the battery/converter connector during extended periods of
power loss of more than 1 week.
2. If luminaire is out of service for more than 1 year, perform annual test
procedure & replace battery packs as needed.
3. Perform visual, electrical and mechanical inspections on a regular basis.
The environment and frequency of use should determine this. However,
it is recommended that checks be made at least once a year. We
recommend an Electrical Preventive Maintenance Program as described
in the National Fire Protection Association Bulletin NFPA No. 70B:
Recommended Practice for Electrical Equipment Maintenance (www.
nfpa.org)
4. The lens should be cleaned periodically to ensure continued lighting
performance.To clean, wipe the lens with a clean, damp cloth. If this is
not enough, use a mild soap or a common liquid cleaner. Do not use an
abrasive, strong alkaline or acid cleaner. Damage may result.
5. Visually check for undue heating evidenced by discoloration of wires or
other components, damaged parts or leakage evidenced by water or
corrosion in the interior. Replace all worn, damaged or malfunctioning
components, and clean gasket seals before putting the luminaire back into
service.
6. Electrically check to make sure that all connections are clean and tight.
7. Mechanically check that all parts are properly assembled.
8. Check and re-torque all mounting hardware.
9. To prevent heat build-up, remove dust from the LED housing using a soft
brush or air pressure.
10. Visually inspect status indicator (charging) indicator light monthly. It
should be illuminated (when AC power ON). If indicator is ashing contact
tech support.
11. Test the emergency operations of the luminaire at 30-day intervals for
a minimum of 30 seconds. The LED load should operate at reduced
illumination in case of power failure
12. Conduct a 90 minute discharge test once a year. The LED load should
operate at reduced illumination for at least 90 minutes.
REPLACEMENT PARTS
(USE LISTED FITTINGS COVERED - LED DRIVERS,
MOUNTING OPTIONS, LED LIGHT ENGINE)
Eaton’s Crouse-Hinds series Pauluhn Linear Emergency LED luminaires are
designed to provide years of reliable lighting performance. However, should
the need for replacement parts arise, they are available through your authorized
Eaton’s Crouse-Hinds distributor. Assistance may also be obtained through your
local Eaton’s Crouse-Hinds representative or the Eaton’s Crouse-Hinds Sales
Service Department, 1201 Wolf Street, Syracuse, New York 13208, Phone
866-764-5454.
All statements, technical information and recommendations contained herein are based on information and tests we believe to be reliable. The accuracy or completeness thereof are not
guaranteed. In accordance with Eaton’s Crouse-Hinds Division’s “Terms and Conditions of Sale,” and since conditions of use are outside our control, the purchaser should determine
the suitability of the product for his intended use and assumes all risk and liability whatsoever in connection therewith.
Eaton’s Crouse-Hinds Division IF 1947
1201 Wolf Street Syracuse, NY 13208 • U.S.A. Revision 1
Copyright© 2022 New 10/22
Figure 14C. UNV1 w/Surge Option Wiring Diagram

LED lineal de emergencia Pauluhn DLLA serie M2
Conexiones de luminarias para lugares peligrosos
Información de instalación y mantenimiento
CONSERVE ESTAS INSTRUCCIONES PARA FUTURAS CONSULTAS
IF 1947
IF 1947 • 10/22 Copyright © 2022, División Crouse-Hinds de Eaton Página 8
APLICACIÓN
Las luminarias LED lineales de emergencia Pauluhn son adecuadas para su uso
en las siguientes zonas peligrosas (clasicadas), como lo establece el Código
Eléctrico Nacional (NEC®):
La luminaria ensamblada debe instalarse según el Código Eléctrico Nacional
NFPA70 y la American Bureau of Shipping.
NEC
• ClaseI, División2, GruposA, B, C, D
• ClaseI, Zona2
• ClaseII, División1, Grupos E, F, G
• ClaseIII
• Ubicación húmeda, IP66/67, Tipo 4X
Estas cubiertas de luminarias se deben utilizar con conexiones de luminarias para
lugares peligrosos Crouse-Hinds incluidos en la lista UL, a saber, motor de luz
LED con n.º de catálogo de la serie DLLA*2 o DLLA*4, que terminan con M2 y
medios de montaje con n.º de catálogo M2-FLUSH- MT-KIT, M2-CEILING-SWIV-
EL-KIT, M2-CEILING-WALL-KIT, M2-PM-KIT-1.25, M2-PM-KIT-1.5, M2-PM-KIT-2.0
(consulte la etiqueta que se proporciona dentro de la cubierta del controlador
para obtener detalles de accesorios permisibles).
Estándares UL:
• UL844 Peligroso (Clasicado)
• UL1598 Luminarias, UL1598A Marina
• UL8750
• UL924
Estándar CSA:
• CSA C22.2 n.º 250
• CSA C22.2 n.º 137
• CSA C22.2 n.º 141
Consulte la placa de identicación del accesorio de la luminaria para obtener
información especíca de la clasicación, adecuación de temperatura ambiente
máxima y la temperatura de operación correspondiente (códigoT).
La luminaria LED lineal ensamblada está diseñada para su uso en interiores y
exteriores, en zonas marinas y húmedas, con presencia de humedad, suciedad,
corrosión, vibración o uso exigente.
VOLTAJE DE ENTRADA:
• UNV1: 120-277VCA 50/60Hz
1. Lea atentamente antes de instalar y cablear la luminaria y consérvelas para
futuras consultas.
2. Asegúrese de que el área se encuentre libre de atmósferas peligrosas du-
rante la instalación y el mantenimiento, así como antes de estos procesos.
3. El uso de equipo accesorio no recomendado por el fabricante puede cau-
sar una condición insegura.
4. Solo utilice piezas de repuesto de la división Crouse Hinds de Eaton.
5. Para evitar el riesgo de incendios, explosiones o descargas eléctricas, solo
un electricista calicado debe instalar, inspeccionar y realizar mantenimien-
to a este producto, de conformidad con los códigos eléctricos aplicables.
6. No use este equipo para ningún uso distinto al previsto.
7. Reemplace toda la unidad de la batería y el controlador LED cuando sea
necesario. Comuníquese con el fabricante para recibir información acerca
del servicio.
8. No intente realizar el mantenimiento de la batería.
9. Consulte la etiqueta del producto para conocer la especicación mínima de
temperatura del cable de alimentación.
10. La batería requiere 24horas para cargarse completamente. El tiempo de
carga debe ser de 24horas, según la batería, para que funcione al máximo
de su capacidad.
11. La batería de emergencia requiere un tiempo de carga mínimo de 1hora
antes de probar el circuito, se requieren 24horas para una carga completa.
12. El equipo debe montarse en sitios y a una altura en los que no sea fácil
que lo manipule personal no autorizado. Altura de montaje máx.: 25,2
pies)
13. La luminaria de emergencia está diseñada para que se instale con CG-
256 (emitido por la American Bureau of Shipping y la Guardia Costera de
Estados Unidos).
14. Este producto se debe instalar de acuerdo con el código de instalación
correspondiente por parte de una persona familiarizada con la construcción
y el funcionamiento del producto, así como los peligros inherentes.
MEDIDAS DE SEGURIDAD IMPORTANTES: LEA Y SIGA TODAS LAS INSTRUCCIONES DE SEGURIDAD
INSTRUCCIONES DE ALMACENAMIENTO
1. Las luminarias EM se deben almacenar en un rango de temperatura
ambiente de 0°C a 40°C.
2. La batería se debe cargar y descargar en un plazo de 6meses. Como
mínimo, la batería debe recargarse dentro de este plazo.
ADVERTENCIA
Para evitar descargas eléctricas:
Asegúrese de que la energía eléctrica esté DESCONECTADA antes y
durante la instalación y el mantenimiento.
Las luminarias se deben alimentar mediante un sistema de cableado con
un cable conductor de conexión a tierra para el equipo, que cumpla con
las normas del NEC y del CEC para las ubicaciones peligrosas específicas
involucradas.
Para evitar quemaduras en las manos:
Asegúrese de que los lentes y la cubierta se encuentren fríos al momento
de realizar el mantenimiento.
!
ADVERTENCIA
Para evitar una explosión:
Asegúrese de que el voltaje de alimentación sea el mismo que el voltaje
de la luminaria.
No la instale en lugares en los que las temperaturas de operación
señaladas superen la temperatura de ignición de la atmósfera peligrosa.
No la use a temperaturas ambientales por encima de las indicadas en la
placa de identificación de la luminaria.
Utilice un cableado de alimentación adecuado, como se indica en la placa
de identificación de la luminaria.
Todos los sellos de las juntas deben estar limpios y sin daños.
Antes de abrir, se debe desconectar la alimentación de la luminaria.
Manténgala herméticamente cerrada cuando se encuentre en
funcionamiento.
Para reducir el riesgo de ignición debido a una descarga electrostática,
evite el contacto con la luminaria cuando se encuentre en una atmósfera
explosiva. Limpie solo con un paño húmedo.
!

INSTALACIÓN
A. M2-FLUSH-MT-KIT
1. Asegúrese de que la alimentación esté desconectada del sistema de
conductos antes de instalar la luminaria.
2. Instale los soportes de montaje empotrados en la parte trasera de la
cubierta del controlador de la luminaria con los dos (2) pernos hexagonales
de 1/4in y las arandelas de seguridad con anillo dividido para cada
soporte. Oriente el soporte como se muestra en la Figura1. Aplique un
torque de 64in-lb (7,2N-m)
3. Identique la ubicación de montaje adecuada para instalar la luminaria,
marque y perfore los oricios para jar los soportes de montaje
empotrado, según las dimensiones que se muestran en la Figura1.
4. La luminaria ahora está lista para el montaje. Se recomienda
encarecidamente que use a dos (2) personas especializadas calicadas
para proceder con el montaje nal de la luminaria. Se recomienda esto
para evitar cualquier lesión personal o daño a la luminaria.
5. Instale y apriete cuatro (4) sujetadores de 1/4in de diámetro
(suministrados por el cliente) en los oricios de montaje del soporte.
Se recomienda utilizar accesorios de acero inoxidable en lugares con
problemas de corrosión.
Figura 1. Instalación de montaje en techo
Longitud 2pies
(in)
2pies
(mm)
4pies
(in)
4pies
(mm)
A 24,0 610 39,0 991
B 24,25 616 24,25 616
C 2,50 63,5 2,50 63,5
THIRD ANGLE PROJECTION
B
C
A
660
26.0
A
123.2
4.85
175.3
6.90
1/4-20 x 1/2" HEX HEAD BOLT
1/2" SPLIT LOCK WASHER
ZONE NO. DESCRIPTION DATE APPRD. LTR. NO.
CCHSY-SW-Template-D
SW_REV 11/2015
DO NOT SCALE DRAWING
NOTES:
1.
A
B
C
D
12
3
4
5
6
7
8
A
D
C
B
8765432 1
Your name
ASSY2 CAT2
CAT1 ASSY1
ARE IN
MILLIMETERS.
DIMENSIONS IN [ ] ARE IN
ALL PRIMARY DIMENSIONS
UNLESS OTHERWISE SPECIFIED,
MM/DD/YYYY
Your Name
WITH ASME Y14.5 2009.
DIM AND TOL IN ACCORDANCE
±
±
±
±
.1 .3
INCHES.
rev
0000000
WT. 15.84 LB
SCALE 1:2
FIRST MADE FOR Catalog Family
Title Line 1
APPROVED BY
DRAWN BY
Finish
... THICK
Material
mm in.
.13
.000
1.5
Your Name
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
AND IS TO BE RETURNED UPON REQUEST.
Title Line 2
Your Name
MM/DD/YYYY
1.5
±
.005
±
.01
±
±
ANGLES
.XXX
.XX
.X
REDRAWN DATE
ORIGINAL DATE
UNLESS OTHERWISE SPECIFIED
TOLERANCES
MATERIAL:
FINISH:
APPROVED BY
CHECKED BY
USED ON
APPLICATION
NEXT ASSY.
TITLE
CODE IDENT. NO.
SIZE
REV.
D
SHEET 1 OF 5
CODE ...
THIRD ANGLE PROJECTION
B
C
A
660
26.0
A
123.2
4.85
175.3
6.90
1/4-20 x 1/2" HEX HEAD BOLT
1/2" SPLIT LOCK WASHER
ZONE NO. DESCRIPTION DATE APPRD. LTR. NO.
CCHSY-SW-Template-D
SW_REV 11/2015
DO NOT SCALE DRAWING
NOTES:
1.
A
B
C
D
12
3
4
5
6
7
8
A
D
C
B
8765432 1
Your name
ASSY2 CAT2
CAT1 ASSY1
ARE IN
MILLIMETERS.
DIMENSIONS IN [ ] ARE IN
ALL PRIMARY DIMENSIONS
UNLESS OTHERWISE SPECIFIED,
MM/DD/YYYY
Your Name
WITH ASME Y14.5 2009.
DIM AND TOL IN ACCORDANCE
±
±
±
±
.1 .3
INCHES.
rev
0000000
WT. 15.84 LB
SCALE 1:2
FIRST MADE FOR Catalog Family
Title Line 1
APPROVED BY
DRAWN BY
Finish
... THICK
Material
mm in.
.13
.000
1.5
Your Name
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
AND IS TO BE RETURNED UPON REQUEST.
Title Line 2
Your Name
MM/DD/YYYY
1.5
±
.005
±
.01
±
±
ANGLES
.XXX
.XX
.X
REDRAWN DATE
ORIGINAL DATE
UNLESS OTHERWISE SPECIFIED
TOLERANCES
MATERIAL:
FINISH:
APPROVED BY
CHECKED BY
USED ON
APPLICATION
NEXT ASSY.
TITLE
CODE IDENT. NO.
SIZE
REV.
D
SHEET 1 OF 5
CODE ...
INSTALACIÓN
Altura de montaje máx. de 7,68m (25,2pies)
B. M2-CEILING-WALL-KT
1. Asegúrese de que la alimentación esté desconectada del sistema de
conductos antes de instalar la luminaria.
2. Marque y taladre los oricios para sujetar los soportes de extremo. Use
dos (2) sujetadores de 1/4in de diámetro (suministrados por el cliente)
en las medidas de centro a centro (consulte la Figura2). Se recomienda
utilizar accesorios de acero inoxidable en lugares con problemas de
corrosión.
3. La luminaria ahora está lista para el montaje. Se recomienda
encarecidamente que use a dos (2) personas especializadas calicadas
para proceder con el montaje nal de la luminaria. Se recomienda esto
para evitar cualquier lesión personal o daño a la luminaria.
4. Para los soportes de extremo de montaje en pared o techo, se
recomienda montar primero un soporte y, luego, mientras se sostiene
la luminaria, insertarlo en el soporte montado, para luego montar el otro
soporte.
5. Oriente la luminaria para obtener la potencia de luz deseada y apriete los
tornillos de jación de 1/4in en los soportes. Aplique un torque de 64in-lb
(7,2N-m).
6. Use un tornillo de jación para limitar la rotación de la luminaria.
Figura 2. Instalación de montaje en pared o techo
Longitud 2pies
(in)
2pies
(mm)
4pies
(in)
4pies
(mm)
A 28,5 724 28,5 724
B 24,0 610 39,0 991
THIRD ANGLE PROJECTION
A
B
175.3
6.90
205.2
8.08
63.5
2.50
54
2.13
B
723
28.5
CCHSY-SW-Template-D
SW_REV 11/2015
DO NOT SCALE DRAWING
NOTES:
1.
A
B
C
D
12
3
4
5
6
7
8
A
D
C
B
8765432 1
Your name
ASSY2 CAT2
CAT1 ASSY1
ARE IN
MILLIMETERS.
DIMENSIONS IN [ ] ARE IN
ALL PRIMARY DIMENSIONS
UNLESS OTHERWISE SPECIFIED,
MM/DD/YYYY
Your Name
WITH ASME Y14.5 2009.
DIM AND TOL IN ACCORDANCE
±
±
±
±
.1 .3
INCHES.
rev
0000000
WT. 15.84 LB
SCALE 1:2
FIRST MADE FOR Catalog Family
Title Line 1
APPROVED BY
DRAWN BY
Finish
... THICK
Material
mm in.
.13
.000
1.5
Your Name
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
AND IS TO BE RETURNED UPON REQUEST.
Title Line 2
Your Name
MM/DD/YYYY
1.5
±
.005
±
.01
±
±
ANGLES
.XXX
.XX
.X
REDRAWN DATE
ORIGINAL DATE
UNLESS OTHERWISE SPECIFIED
TOLERANCES
MATERIAL:
FINISH:
APPROVED BY
CHECKED BY
USED ON
APPLICATION
NEXT ASSY.
TITLE
CODE IDENT. NO.
SIZE
REV.
D
SHEET 2 OF 5
CODE ...
!
ADVERTENCIA
Para evitar provocar lesiones al personal, no deje la luminaria colgando
ni la exione en un soporte a la vez. No seguir esta instrucción dará como
resultado la rotura del soporte y en posibles lesiones o en la muerte.
!
ADVERTENCIA
Para evitar provocar lesiones al personal, no deje la luminaria colgando
ni la exione en un soporte a la vez. No seguir esta instrucción dará como
resultado la rotura del soporte y en posibles lesiones o en la muerte.
IF 1947 • 10/22 Copyright © 2022, División Crouse-Hinds de Eaton Página 9
PERNO DE CABEZA
HEXAGONAL 1/4-20 x 1/2 in
ARANDELA DE SEGURIDAD
DIVIDIDA DE 1/2 in
[175.3]
6,90
[123.2]
4,85
B
C
A
[660]
26,0
A
[63.5]
2,50
[205.2]
8,08
[175.3]
6,90
[54]
2,13
A
B
[723]
28,5
B

C. M2-CEILING-SWIVEL-KIT
1. Asegúrese de que la alimentación esté desconectada del sistema de
conductos antes de instalar la luminaria.
2. Identique la ubicación de montaje adecuada para instalar la luminaria,
marque y perfore los oricios para jar los soportes giratorios de acuerdo
con la dimensión de centro a centro “A” en la tabla a continuación (ver
Figura 3).
3. Monte los conjuntos de soporte giratorio en la cubierta del controlador de
la luminaria, como se muestra en la Figura3. Utilice dos (2) de los pernos
hexagonales de 1/4in proporcionados y arandelas de seguridad con anillo
dividido para cada soporte. Aplique un torque de 64in-lb (7,2N-m).
4. La luminaria ahora está lista para el montaje. Se recomienda
encarecidamente que use a dos (2) personas especializadas calicadas
para proceder con el montaje nal de la luminaria. Se recomienda esto
para evitar cualquier lesión personal o daño a la luminaria.
5. Instale y apriete los sujetadores de 1/4in de diámetro (suministrados
por el cliente) en cada uno de los oricios de montaje del soporte.
Se recomienda utilizar accesorios de acero inoxidable en lugares con
problemas de corrosión.
6. Ajuste la posición de la luminaria al ángulo deseado, ajuste los dos (2)
pernos de pivote de 5/16in rmemente al soporte y, luego, apriete las
tuercas hexagonales. Aplique un torque de 120in-lb (13,6N-m).
Longitud 2pies
(in)
2pies
(mm)
4pies
(in)
4pies
(mm)
A 26,4 670 26,4 670
B 24,0 610 39,0 991
Figura 3. Instalación del montaje giratorio en techo
THIRD ANGLE PROJECTION
166.9
6.57
175.3
6.90
A
B
B
669.3
26.35
1/4" SPLIT LOCK WASHER
1/4-20 x 1/2" CAP SCREW
CCHSY-SW-Template-D
SW_REV 11/2015
DO NOT SCALE DRAWING
NOTES:
1.
A
B
C
D
12
3
4
5
6
7
8
A
D
C
B
8765432 1
Your name
ASSY2 CAT2
CAT1 ASSY1
ARE IN
MILLIMETERS.
DIMENSIONS IN [ ] ARE IN
ALL PRIMARY DIMENSIONS
UNLESS OTHERWISE SPECIFIED,
MM/DD/YYYY
Your Name
WITH ASME Y14.5 2009.
DIM AND TOL IN ACCORDANCE
±
±
±
±
.1 .3
INCHES.
rev
0000000
WT. 15.84 LB
SCALE 1:2
FIRST MADE FOR Catalog Family
Title Line 1
APPROVED BY
DRAWN BY
Finish
... THICK
Material
mm in.
.13
.000
1.5
Your Name
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
AND IS TO BE RETURNED UPON REQUEST.
Title Line 2
Your Name
MM/DD/YYYY
1.5
±
.005
±
.01
±
±
ANGLES
.XXX
.XX
.X
REDRAWN DATE
ORIGINAL DATE
UNLESS OTHERWISE SPECIFIED
TOLERANCES
MATERIAL:
FINISH:
APPROVED BY
CHECKED BY
USED ON
APPLICATION
NEXT ASSY.
TITLE
CODE IDENT. NO.
SIZE
REV.
D
SHEET 3 OF 5
CODE ...
THIRD ANGLE PROJECTION
166.9
6.57
175.3
6.90
A
B
B
669.3
26.35
1/4" SPLIT LOCK WASHER
1/4-20 x 1/2" CAP SCREW
CCHSY-SW-Template-D
SW_REV 11/2015
DO NOT SCALE DRAWING
NOTES:
1.
A
B
C
D
12
3
4
5
6
7
8
A
D
C
B
8765432 1
Your name
ASSY2 CAT2
CAT1 ASSY1
ARE IN
MILLIMETERS.
DIMENSIONS IN [ ] ARE IN
ALL PRIMARY DIMENSIONS
UNLESS OTHERWISE SPECIFIED,
MM/DD/YYYY
Your Name
WITH ASME Y14.5 2009.
DIM AND TOL IN ACCORDANCE
±
±
±
±
.1 .3
INCHES.
rev
0000000
WT. 15.84 LB
SCALE 1:2
FIRST MADE FOR Catalog Family
Title Line 1
APPROVED BY
DRAWN BY
Finish
... THICK
Material
mm in.
.13
.000
1.5
Your Name
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
AND IS TO BE RETURNED UPON REQUEST.
Title Line 2
Your Name
MM/DD/YYYY
1.5
±
.005
±
.01
±
±
ANGLES
.XXX
.XX
.X
REDRAWN DATE
ORIGINAL DATE
UNLESS OTHERWISE SPECIFIED
TOLERANCES
MATERIAL:
FINISH:
APPROVED BY
CHECKED BY
USED ON
APPLICATION
NEXT ASSY.
TITLE
CODE IDENT. NO.
SIZE
REV.
D
SHEET 3 OF 5
CODE ...
D. M2-PM-KIT-*
1. Asegúrese de que la alimentación esté desconectada del sistema de
conductos antes de instalar la luminaria.
2. Verique que el diámetro interno de la abrazadera coincida con el diámetro
del poste antes de la instalación. Las abrazaderas están disponibles en
tamaños de 1,65in (42mm), 2,00in (51mm) y 2,36in (60mm) (consulte
la Figura5).
3. Los soportes de montaje en poste tienen una separación de 20,75in en
las líneas centrales del soporte, como se muestra en la Figura4.
4. Apriete dos (2) de los pernos hexagonales de 1/4in proporcionados
y arandelas de seguridad con anillo dividido en cada subconjunto de
soporte. Aplique un torque de 64in-lb (7,2 N-m).
5. Retire los dos (2) tornillos de 5/16in, las arandelas de seguridad y
las tuercas de cada abrazadera y quite las mitades superiores de las
abrazaderas.
6. La luminaria ahora está lista para el montaje. Se recomienda
encarecidamente que use a dos (2) personas especializadas calicadas
para proceder con el montaje nal de la luminaria. Se recomienda esto
para evitar cualquier lesión personal o daño a la luminaria.
7. Levante la luminaria en posición de tal manera que el poste encaje en las
mitades inferiores de las abrazaderas.
8. Instale las dos (2) mitades superiores de las abrazaderas y los tornillos de
5/16in, las arandelas de seguridad y las tuercas en cada abrazadera.
9. Ajuste uniformemente las tuercas en los tornillos de 5/16in con una
secuencia hacia delante y hacia atrás. Aplique un torque de 120in-lb
(13,6N-m).
Cat. N.º Conguración
Dimensión (pulgadas)
A B C D
M2-PM-KIT-1.25 Kit PM 2.0 (tamaño
comercial 2in) 4,331 3,543 2,36 1,693
M2-PM-KIT-1.5 Kit PM 1.5 (tamaño
comercial 1 - 1/2in) 3,740 2,953 2,00 1,535
M2-PM-KIT-2.0 Kit PM 1.25 (tamaño
comercial 1 - 1/14in) 3,386 2,598 1,65 1,378
Longitud 2pies
(in)
2pies
(mm)
4pies
(in)
4pies
(mm)
A 24,0 610 39,0 991
BConsulte la siguiente tabla para conocer los
diámetros de las abrazaderas de tubo.
Figura 4. Instalación de montaje en poste
Figura 5. Detalles del montaje en poste
THIRD ANGLE PROJECTION
A
527.1
20.75
A
171
6.7
B
175.3
6.90
198
7.8
A
C
D
B
CCHSY-SW-Template-D
SW_REV 11/2015
DO NOT SCALE DRAWING
NOTES:
1.
A
B
C
D
12
3
4
5
6
7
8
A
D
C
B
8765432 1
Your name
ASSY2 CAT2
CAT1 ASSY1
ARE IN
MILLIMETERS.
DIMENSIONS IN [ ] ARE IN
ALL PRIMARY DIMENSIONS
UNLESS OTHERWISE SPECIFIED,
MM/DD/YYYY
Your Name
WITH ASME Y14.5 2009.
DIM AND TOL IN ACCORDANCE
±
±
±
±
.1 .3
INCHES.
rev
0000000
WT. 15.84 LB
SCALE 1:2
FIRST MADE FOR Catalog Family
Title Line 1
APPROVED BY
DRAWN BY
Finish
... THICK
Material
mm in.
.13
.000
1.5
Your Name
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
AND IS TO BE RETURNED UPON REQUEST.
Title Line 2
Your Name
MM/DD/YYYY
1.5
±
.005
±
.01
±
±
ANGLES
.XXX
.XX
.X
REDRAWN DATE
ORIGINAL DATE
UNLESS OTHERWISE SPECIFIED
TOLERANCES
MATERIAL:
FINISH:
APPROVED BY
CHECKED BY
USED ON
APPLICATION
NEXT ASSY.
TITLE
CODE IDENT. NO.
SIZE
REV.
D
SHEET 4 OF 5
CODE ...
THIRD ANGLE PROJECTION
A
527.1
20.75
A
171
6.7
B
175.3
6.90
198
7.8
A
C
D
B
CCHSY-SW-Template-D
SW_REV 11/2015
DO NOT SCALE DRAWING
NOTES:
1.
A
B
C
D
12
3
4
5
6
7
8
A
D
C
B
8765432 1
Your name
ASSY2 CAT2
CAT1 ASSY1
ARE IN
MILLIMETERS.
DIMENSIONS IN [ ] ARE IN
ALL PRIMARY DIMENSIONS
UNLESS OTHERWISE SPECIFIED,
MM/DD/YYYY
Your Name
WITH ASME Y14.5 2009.
DIM AND TOL IN ACCORDANCE
±
±
±
±
.1 .3
INCHES.
rev
0000000
WT. 15.84 LB
SCALE 1:2
FIRST MADE FOR Catalog Family
Title Line 1
APPROVED BY
DRAWN BY
Finish
... THICK
Material
mm in.
.13
.000
1.5
Your Name
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
AND IS TO BE RETURNED UPON REQUEST.
Title Line 2
Your Name
MM/DD/YYYY
1.5
±
.005
±
.01
±
±
ANGLES
.XXX
.XX
.X
REDRAWN DATE
ORIGINAL DATE
UNLESS OTHERWISE SPECIFIED
TOLERANCES
MATERIAL:
FINISH:
APPROVED BY
CHECKED BY
USED ON
APPLICATION
NEXT ASSY.
TITLE
CODE IDENT. NO.
SIZE
REV.
D
SHEET 4 OF 5
CODE ...
THIRD ANGLE PROJECTION
A
527.1
20.75
A
171
6.7
B
175.3
6.90
198
7.8
A
C
D
B
CCHSY-SW-Template-D
SW_REV 11/2015
DO NOT SCALE DRAWING
NOTES:
1.
A
B
C
D
12
3
4
5
6
7
8
A
D
C
B
8765432 1
Your name
ASSY2 CAT2
CAT1 ASSY1
ARE IN
MILLIMETERS.
DIMENSIONS IN [ ] ARE IN
ALL PRIMARY DIMENSIONS
UNLESS OTHERWISE SPECIFIED,
MM/DD/YYYY
Your Name
WITH ASME Y14.5 2009.
DIM AND TOL IN ACCORDANCE
±
±
±
±
.1 .3
INCHES.
rev
0000000
WT. 15.84 LB
SCALE 1:2
FIRST MADE FOR Catalog Family
Title Line 1
APPROVED BY
DRAWN BY
Finish
... THICK
Material
mm in.
.13
.000
1.5
Your Name
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
AND IS TO BE RETURNED UPON REQUEST.
Title Line 2
Your Name
MM/DD/YYYY
1.5
±
.005
±
.01
±
±
ANGLES
.XXX
.XX
.X
REDRAWN DATE
ORIGINAL DATE
UNLESS OTHERWISE SPECIFIED
TOLERANCES
MATERIAL:
FINISH:
APPROVED BY
CHECKED BY
USED ON
APPLICATION
NEXT ASSY.
TITLE
CODE IDENT. NO.
SIZE
REV.
D
SHEET 4 OF 5
CODE ...
!
ADVERTENCIA
Para evitar provocar lesiones al personal, no deje la luminaria colgando
ni la exione en un soporte a la vez. No seguir esta instrucción dará como
resultado la rotura del soporte y en posibles lesiones o en la muerte.
!
ADVERTENCIA
Para evitar provocar lesiones al personal, no deje la luminaria colgando
ni la exione en un soporte a la vez. No seguir esta instrucción dará como
resultado la rotura del soporte y en posibles lesiones o en la muerte.
IF 1947 • 10/22 Copyright © 2022, División Crouse-Hinds de Eaton Página 10
TORNILLO DE CABEZA DE 1/4-20 x 1/2 in
ARANDELA DE SEGURIDAD DIVIDIDA DE 1/4 in
[166.9]
6,57
B
[175.3]
6,90
[669.3]
26,35
B
[175.3]
6,90
[171]
6,7
[198]
7,8
B
[527.1]
20,75
A
A
A
B
C
D
A