MLT T205 User manual

Wireless Tire Pressure Detector
User Manual
T205

1. Before Use
1.1 Introduction of Product Safety
1.2 Check Accessories
1.3 Introduction of Product Function
2.Method of Installation
2.1 HUD of Installation
2.2 Sensor Installation
2.3 Troubleshooting for Installation
3.Installation Accomplishment
3.1 Wireless Signal Reception
4. Operation and Set-up
4.1 Function Key and Set-up Key Operation
4.2 Warnings and Legends
4.3 Tire Status Check-up
5.Electric Utensil Regulation
5.1 HUD of Installation
5.2 Sensor
Table of content

1.使用前說明
1.1Introduction of Product Safety:
Wireless tire pressure monitoring system, is a wireless vehicle safety equipment. can be
battery and individual tire temperature·pressure·battery voltage important information at any
time alert drivers that the operation status of the tire, reduce broke down and driving security
issues.
While any abnormal condition is detected, the value in the voices/lights issued a warning to
drivers attention.
1.2 ssories List: 1.3 Introduction of Product Function
1. Before Use
Parts Quantity
Host Unit 1
Power Cable
(cigarette lighter
Connector )
1
Sensor 4
CR1632, Battery 4
Fixing bracket 1
Anti-theft Nut 4
Wrench 1
User Manual 1
Parts Quantity
Host Unit 1
Power Cable
(cigarette lighter
Connector )
1
Sensor 4
CR1632, Battery 4
Fixing bracket 1
Anti-theft Nut 4
Wrench 1
User Manual 1
Power connector
Function Key Set-up Key
Photosensitive Test Area
Power switch
Power connector
Function Key Set-up Key
Photosensitive Test Area
Power switch

1.3.1 Function Key
Press [Function key] under normal mode to display settings in a cycle.
1.3.2 Set-up Key
Move to the function mode desired with [Function Button] and press [Set-up Button] to reset;
press [Function Button] to exit settings once accomplishment.
Function
Key
Set-up
Key
Tire Temperature Upper
Limits settings
Tire Pressure lower Limits
Settings
Tire Pressure Bottom
Limits Settings
Tire Pressure
Display
Tire Temperature
Display
Battery Voltage
Display
Function
Key
Set-up
Key
Tire Temperature Upper
Limits settings
Tire Pressure lower Limits
Settings
Tire Pressure Bottom
Limits Settings
Tire Pressure
Display
Tire Temperature
Display
Battery Voltage
Display

2.安裝方法
2.1 Host Unit Installation
First Step : Search position of Host Unit
/ Cigarette lighter Connector
(Figure I -2 )
Instruction :
1.Circular connector connected host the rear
cigarette lighter connector connected to the car
cigarette lighter socket.
Second Step : Turn on the power ,the display will
start ( Figure 3-4 )
Instruction :
If Cigarette lighter, turn off the engine, the power will be
shut down, the host switch normally open.
If engine is shut down, the power will not turn off will be required to
host the rear of the switch to turn off or unplug the cigarette lighter
plug to prevent battery power depletion.
(Figure 5-6 )
( Figure I )
(Figure 3 )
(Figure 5 )
(Figure 4 )
(Figure 6 )
( Figure 2 )
2.Installation

Step 3 : Host fixing bracket connection
Instruction :
1 . Holder bracket fixing hole behind the insertion host ( Figure 7 ~ 8 )
2 . Mounting bracket affixed to the glass on the appropriate location,And vacuum adsorption locked
(Clockwise locking) ( Figure 9 )
Step 1: Make sure four Sensor are pasted with tire position sticker
Instruction :
1.Take 4 Sensor and make sure if stickers marking 4 different positions of tires are
pasted onto, R 1(Right Front)/R2(Right Rear)/L1(Left Front)/L2(Left Rear)
Step 2 : Install Battery of SENSOR
Instruction :
1. Put batteries and snaps into Sensor by sequence and fasten up the lid.(Figure 11 )
Precaution:
1.Negative pore of the battery shall be at bottom side and positive pore at upper
side;it will discharge instantly and run out of power if in reverse placement.
2.Please fasten up the lid completely to avoid penetration of vapor.
2.2 Sensor Installation
(Figure 7 ) ( Figure 8 ) (Figure 9 )
(Figure 11 )
LOCK
RF(R1)
RR(R2)
LF(L1)
LR(L2)
(Figure 10 )
RF(R1)
RR(R2)
LF(L1)
LR(L2)
(Figure 10 )

Step 3 : Install Sensor on the Tire
Instruction :
Every piece of Sensor is identified by a unique ID Code (tire positioned with HUD), and paste
its label on the Sensor (LF(L1) RF(R1)..).
1.Remove the plastic gas nozzle on the tire first and fasten it up with anti-theft nut; make sure
Sensor’s tire position labels are matched in tires’ positions, then install and fasten them on
the gas nozzle.
Step 4 : Sensor Fasten-up
Instruction:
1.Swivel the anti-theft nut toward direction of the sensor. (Figure 16)
2.Take the wrench to buckle anti-theft nut with one hand and seize sensor with another hand to fasten up
with each other inward. (Figure 17- 18)
3.Check if Sensor has been installed and fastened correctly.
(Figure 12-15 )
(Figure 12) (Figure 13)
(Figure 16) (Figure 17) (Figure 18)
(Figure 14) (Figure 15)
Precaution: please must fasten sensor and gas nozzle; it might have gas leakage if failed to do.Precaution: please must fasten sensor and gas nozzle; it might have gas leakage if failed to do.Precaution: please must fasten sensor and gas nozzle; it might have gas leakage if failed to do.

2.3 Trouble-shooting of issues frequently happened during Installation
FAQ 1 : After HUD is power on for 5 minutes, it remains failure of receiving wireless signal
(unable to receive signal transmitted from 4 pieces of Sensor in 5 minutes).
Resolution:
1. Please make sure if the batteries are in reverse. (Negative is poured at bottom side and positive at upper
side)
2. Please make sure the snap of battery is fastened and in close of the batteries.
3. Please make sure if voltages in the batteries are enough; please replace with new ones if less than 2.6V.
4. Please disassemble the battery, replace the battery once.
5. Please swivel the lid and check if penetration of any vapor occurred which caused battery snap or rust and
malfunction.
(Please be sure to fasten up the lid and adhere it with rubber ring to avoid penetration of vapor)
Precautions:
The system is operated on wireless signal, under certain situation, the system
may be unable to receive or reduce down the wireless signal as a result of
environment intervention, mistakes made during operation and improper
installation.
When the tire cannot receive updated RF signal in 5 minutes consecutively, its
red legend light will be on to warn drivers.
When any of following situation happened, please:
1. Drive away the car (it might be strong wireless signal intervention nearby)
2. Please check if battery of Sensor is running out (less than 2.6Volt); please
replace it with new one.
3. Please contact with your dealer for assistance.
FAQ 2: What should I do when the Sensor is with problems caused from lack of tire position
labels, tire position duplication or labels drop?
Resolution:
1.We have done ID code settings on display and 4 pieces of Sensor while in delivery; in case of aforesaid problems,
please consult with your dealer for reset to avoid misplacements.
(Figure 19) (Figure 20)
Battery
Snaps
adhere.
Battery
Snaps are
not
adhered.

3.2 Wireless Signal Reception
Step Description Display on HUD
1Start the engine, power
turned on.
For turn on the power
switch, Into the
receiving state.
2When the Host receives
RF signal from Sensor,
the red light on the tire
will extinguish one after
one. Displays PSI and
of tire pressure value.
3When four sensors
(RF), after receiving
host will show tires,
PSI and tire pressure of
reading.

4. 操作與設定
4.1 Function Key and Set-up Key
Operation
Function Key Description Display on HUD
Do not press Showing pressure value of the battery
voltage and tire pressure
Press once Tires, temperature and the left front tire
semaphored left front wheel the value “60”
appears on the left front tire temperature
limit can be the right setting, each time
press the increase “1” ℃
Press 2 times Tires, temperature, and the right front tire
light will be on and the right front wheel of
the value "60" may be right to set the upper
limit of the right front tire temperature, each
time press the increase "1" ℃
Press 3 times Tires, the temperature and the light is on
the right rear tire and the right rear wheel to
the value "60" appears on the right rear tire
temperature limit can be the right setting
for every Press once increase of 1 "° ℃
Press 4 times Tires, temperature, and the left rear tire
semaphored left rear wheel the value "60"
appears on the left rear tire temperature
limit can be the right setting, for each Press
once the increase "1" ℃
4.Operation and Settings