MO-EL IRIS 866N01-866NP User guide
IRIS
Classe I - IP 55
MO-EL S.p.a.
Via Galvani, 18
42027 Montecchio Emilia (RE)
ITALY
tel +39 (0522) 868011
fax +39 (0522) 864223
HALOGEN QUARTZ INFRARED HEATER
USE AND MAINTENANCE
IRIS
• Scansiona il QR per vedere un video d’aiuto
• Scan the QR to see a help video
• Scannez le QR pour voir une vidéo d’aide
• Scannen Sie den QR, um ein Hilfevideo anzuzeigen
• Escanee el QR para ver un video de ayuda
3
1. IMPORTANT SAFETY INSTRUCTIONS
Instructions should be carefully read before installation and retained
by the user. The booklet must be keeped and delivered to the new
user in case of cession of the machine.
1. This appliance is intended solely for the use it has been designed
for, namely the achievement and maintance of a ertain thermal
comfort for the people by means of irradiation on them.
2. After unpacking make sure that the appliance is complete and
shows no signs of visible damage or tampering.
3. Keep packing materials, which are potential dangers, away from
children.
4. The device can be used by children at least 8 years (as well as by
persons with reduced physical, sensory or mental capabilities, or
lack of experience or required knowledge) provided that they are
under surveillance, or after they have been instructed relating to
the safe use and have understood the potential dangers. Children
should not play with the appliance. Cleaning and maintenance
must be performed by the user and not by unsupervised children.
5. Children of less than 3 years should be kept away unless
continuously supervised.
6. Children aged from 3 years and less than 8 years shall only switch
on/off the appliance provided that it has been placed or installed
in its intended normal operating position and they have been
given supervision or instruction concerning use of the appliance
in a safe way and understand the hazards involved.
7. Children aged from 3 years and less than 8 years shall not plug in,
regulate and clean the appliance or perform user maintenance.
8. Do not use it in small rooms used by people who are unable to
leave such rooms on their own unless they are under constant
surveillance.
9. Before inserting the plug make sure that the voltage is the same
as indicated on the device.
10. Do not use in presence of gas, inammable or explosive liquids
or substances.
EN USE AND MAINTENANCE
4
11. Some fundamental rules which apply to all electrical devices
must be observed when using the heater:
• Do not touch the heather with wet hands.
• Do not handle with bare feet.
• Do not pull the electric cord or the device itself to unplug it
from the socket; pull the plug directly.
12. Avoid the use of an extension cord with this product, because
the extension cord may overheat and cause a risk of re.
13. Do not apply any modication to the product that could
compromise the safety.
14. Keep connections dry.
15. If the power supply cord is damaged, avoid to use the appliance.
For power cord replacing, please contact the manufacturer or the
technical service or a person with similar qualication, in order to
avoid any risk.
16. If the appliance is not used for a long period, disconnect it from
the power supply.
17. Always unplug the appliance before doing any maintenance
operation.
CAUTION — Some parts of this product can become very hot
and cause burns. Particular attention has to be given where
children and vulnerable people are present.
2. ELECTRICAL INSTALLATION
The installation should always be carried out by a qualified
electrician or a competent person in accordance with the
standards HD 384 CENELEC for Europe, or international IEC
60346-7-708 1988 and according to the UE 2015/1188 standards. The
energy supply must be done through a properly grounded socket and
the impedance of the electrical network must be less than 0.3 ohm.
An overvoltage category III Combined Circuit breaker and Residual
Current Device (RCD) with rated earth leakage operation not
exceeding 30mA must be fitted upstream on the supply line. The
circuit breaker must have a contact opening distance of at least 3
mm.
Be careful to connect the heater to a supply line protected by 16 A
fuses not quick-acting type.
5
• The heaters should always be installed horizontally only using the
mounting brackets provided. This ensures correct positioning and
adequate clearance.
• A minimum air gap of 40 cm should always be allowed between
the top of the heater and a ceiling or roof. The appliance should be
60 cm far from the walls (g.1).
• A safety distance of not less than 100 cm should always be left in
front of the IRIS heaters or too near.
• This unit should be mounted at a minimum of 180 cm above ground
level (g.1). If installed in a toilet, the height should be 225 cm in
zone 1 and zone 2; in zone 3 the minimum above ground level is
180 cm, according with the rules of each Country.
• Be sure that the heater is not facing the ceiling or inammable
substances.
• The appliance must not be located neither directly below, nor in
front of a socket-outlet.
• The heater must be installed so as to prevent that the switches can
be touched from those who are in the shower.
• Ensure that there is no possibility of inammable material,
combustible material or curtains coming into contact with the
heater, or lie near the heater.
• Heaters should not be installed in areas where hazardous vapours
may be present. Dened in BS5345.
• The heaters are tted with safety guards. These are intended only
to stop large objects from hitting the emitters. On no account
should the heater be operated with the guard removed.
• For consumer use the heaters are tted with high temperaure
silicone rubber exible cable (H05 RN-F) conforming to BS 6500.
• The models for professional use, that are marked with a “P” in the
code, do not have the power cord and the switch. For professional
installation, cabling of the same specication should be selected.
• The product is in class I and IP55, wich is the protection rate for
the units to be used even outdoor. For keeping the protection rate
of the appliance, the connection of the appliance with the power
supply must be done by means of a minimum IP55 system, as per
the standards HD 384 CENELEC for Europe, or international IEC
60346-7-708 1988.
6
3. LOCATION
All irradiation heaters are designed to achieve and maintain a certain
thermal comfort to the people who need it both outside and inside. It
is therefore very important to carefully study the area where people
stay and consequently direct the radiation towards them.
The IRIS range of heaters is deliberately designed to be very exible
in the choice of position.
There are three basic options:
• A wall mounting bracket version with a specifically designed
fitting for wall attachment . Before drilling the holes for the
dowels, be sure that the wall is solid and that you are far from water
tubes or electrical wires. For xing the appliance at the wall, drill
four holes with a 5 mm diameter bit and x the wall bracket with
the dowels and screws (not supplied)(g.2). With the two screws
supplied, x the two brakets attached to the aluminum tube on the
back of the appliance and lock it in the right angle (g.3).
• A chain suspended version. With 2 supplied S-hook, x the
two supports attached to the aluminum tube on the back of the
appliance to the last link in the chain. Fix the opposite end of the
chain to the support attached to the wall or where there is another
xing point. (Fig. 4)
Ensure that the supply cable is well mounted and that it does
not come into contact with the reflector of the heater or that
it does not trail into the heated area.
4. USE
The IRIS range consists of a 1200 W heater and an 1800 W heater.
The essential element of the heater is the halogen lled quartz linear
lamp with a tungsten element. The heater operates at full output
almost immediately. The heating reaches a distance of about 3
meters in front of the appliance.
Avoid exposing skin to the rays of the appliance for distances
less than 50 cm.
Avoid exposing eyes to the rays of the appliance for distances
less than 2.70 m.
All users should be made aware of all aspects of operation and safety
and these instructions should be retained for reference.
7
Switch on heater (in the models that have the switch) and conrm
that emitter is operating. Ensure that the heater is aiming its warmth
into the target area by adjusting heater angles as necessary.
Do not use the heater directly near a bathtub, a shower, a swimming
pool. In unoccupied premises it is recommended that the heating
system is switched off and isolated from the electrical supply.
5. MODELS WITH REMOTE CONTROL (NRC01)
Both models are available with remote control to remotely control
the heater.
Insert 2 x 1.5V AAA batteries (not included in the package) into the
remote control, respecting the indicated polarities.
Connect the appliance to the power supply:
- The STAND-BY LED lights up.
- By pressing the ON button on the remote control, the product lights
up together with the ON LED.
- Press the STAND-BY button on the remote control, or the button
on the product next to the LEDs, to turn off the lamp and return the
appliance to sleep mode.
Warning! The appliance is still live.
To detach the line completely unplug the device.
6. MAINTENANCE
Mo-El IRIS heaters contain no moving parts and therefore very
little maintenance is required other than to ensure that there is no
excessive build-up of dust/dirt on the reectors or emitters as this
can cause overheating and premature emitter failure. To clean the
appliance, wipe off with a damp cloth.
The accumulation of limestone or incrustations reduces the life and
the efciency of the lamp; it is suggested therefore to avoid the
continued use in presence of water or salt fog. Eventual leavings
of salt water will have to be removed before the use, after having
disconnected the appliance, by means of soak in sweet water.
8
7. EMITTER AND SILICON BUMPERS REPLACEMENT
The emitters used in the IRIS are robust and if knocks and shock
vibrations are avoided, they will last for around 5000 hours. When
changing the lamp, also the silicon bumpers connected with the lamp
must be substituted. They should be substituted even before if there
are signs of aging. Due to the special sealing and anti-shock design
of the heater, the emitters are not intended to be user replaceable.
Please ensure that all emitters are replaced via the Mo-El service
network.
8.TECHNICAL FEATURES
866N01-866NP
866NRC01
867N01-867NP
867NRC01
Power supply 220-240 V ~ 50-60 Hz 220-240 V ~ 50-60 Hz
Power 1200 W 1800 W
Insulation Class I I
Protection level IP55 IP55
Lamp Quartz - tungsten wire
Lamp life (hours) 5000 5000
Emission IR-A IR-A
Range (m2)4÷6 8÷10
Weight (kg) 0.95 1
Dimensions (mm) 725x125x85 830x125x85
9
1
1
ED
9006ED/9005ED
2
3
48
53
683
7
83
8
ED
9
10
11
•
•
•
10
12
13
14
15
16
17
2
0,3
3
16
30
•
•40
160
•
•1180
321225
180
•
•
•
11
•
•
•
•
•P
•IP55
IP55
3
•
5
2
3
•
4
4
18001200
12
3
50
2,70
5
AAA1,5
«
6
13
7
5000
8
6050230220
6050230220
1800 1200
I I
IP55 IP55
5000 5000
10÷8 6÷4 2
1 0,7
85×125×830 85×125×725
8
2002/96/EC
14
Fig. 1
Fig. 2
Fig. 3
Fig. 4
15
008241 - 03/2022
This manual is available in digital format on the website
www.mo-el.com
This manual suits for next models
3
Table of contents
Languages:
Other MO-EL Heater manuals
MO-EL
MO-EL HATHOR DEEP 892P User guide
MO-EL
MO-EL PETALO 722CP User guide
MO-EL
MO-EL STILUOVO User guide
MO-EL
MO-EL IRIS 866N User guide
MO-EL
MO-EL Fiore User guide
MO-EL
MO-EL Fiore 766 User guide
MO-EL
MO-EL BLACKLIGHT Series User guide
MO-EL
MO-EL Fiore User guide
MO-EL
MO-EL PETALO Series User guide
MO-EL
MO-EL AAREN 966W User guide
