Mobile Pixels TRIO User manual

TRIO & TRIO MAX
Portable Laptop Monitor
USER GUIDE

1.1 MONITOR
SECTION : PACKAGE OVERVIEW
1.2 ACCESSORIES
MAGNETIC PLATES
SCREEN
INTERCHANGEABLE
USB TYPE-C PORTS
BACKCHARGING PORT
AND SIGNAL PORT
METAL PLATE
12 METAL PLATES TOTAL
FOR 3 LAPTOPS
USB CABLE
USB TYPE-C CABLE
TO TYPE A
USB TYPE-C CABLE
TO TYPE C
TRIO/TRIO MAX CLIP
EACH TRIO/TRIO MAX WILL INCLUDE
ONE TRIO CLIP.THUS, ONCE TWO
TRIOS/TRIO MAX'S ARE PURCHASED,
YOU WILL HAVE A SET TO CLIP THEM
TOGETHER
1

Double click and launch the installer.
Click “Yes” in the window below.
2.
3.
Click ”Next” in the Window below:
4.
Please select “I accept the terms of the license agreement”
and click Next
5.
Please select “Yes, I want to restart my computer now”
and click Finish
6.
Please download the correct windows driver from:
1.
WWW.MOBILEPIXELS.US/PAGES/DOWNLOAD-DRIVERS
2.1 WINDOWS INSTALLATION GUIDE
SECTION : DRIVER INSTALLATION GUIDE
When using USB C to connect, driver installation is not necessary.
Connect Windows Laptop to Mobile Pixels Trio/Trio Max Monitor, wait 20 secs and the monitor
should turn on. In the event the monitor does not turn on, please follow the steps below:
2

Click “MP_Graphics_Driver_v1.0.0.pkg”, please follow
the instructions to install the device driver.
2.
(After System Reboot) Connect Mobile Pixels device to Mac
computer, a screen recording prompt should pop up
“Click Open System Preferences”
4.
Go to System Preferences > Security & Privacy > Privacy
5.
Click on the Lock to make changes
6.
Scroll and select “Screen Recording” and check
“DJTVirtualDisplayAgent”
7.
Click on the Lock to save changes Click “Quit Now”
8.
3.
The system should pop‐up a screen “System Extension
Blocked” after installation asks the user to enable these
extensions forthe first time .Click “Open Security
Preference” go to setting and restart the laptop.
1.
Please download the Mac driver from the link below.
Run the .pkg file to load the drivers to the mac folder
WWW.MOBILEPIXELS.US/PAGES/DOWNLOAD-DRIVERS
Important: This warning is not always shown. Even if it
is not shown, for new installations the user must
“Allow” to install the Mobile Pixels driver.
. MAC INSTALLATION GUIDE
Do not plug the Mobile Pixels Device into your mac before executing the driver installation
3

Front of
the laptop
Once the metal plates are all placed, close your
laptop and align TRIO/TRIO MAX.
3.
Place the metal plates (included in the box) over
the magnets in the back of TRIO/TRIO MAX.
1.
For a proper install try to match the right edge of
TRIO/TRIO MAXwith one screw exposed past the edge
of the laptop.
Align bottom of TRIO/TRIO MAX to bottom of the laptop.
4.
Make sure round plate is centered on the magnet
2.
*USB Cable omitted
36
. ATTACHMENT MODE
SECTION : MONITOR POSITIONING GUIDE
4

To use it on the other side, rotate 180 degrees.
2.
You are ready to work.
4.
To remove it, slide TRIO/TRIO MAX off of the
magnets, do not pull.
1.
Snap into the back of the laptop.
3.
*USB Cable omitted
5

1.
Slide Trio
2.
Rotate around 110° degrees
3.
Connect Trio to the Pc and use it in portrait mode
4.
Go to Display settings to rotate display
See section 4.2
*USB Cable omitted
3.2 PORTRAIT MODE
6

1.
To access
presentation mode,
simply swivel
TRIO/TRIO MAX 180
degrees to the back of
the laptop.
*USB Cable omitted
180º
3.4 PRESENTATION MODE
7

1.
Attach the clips to Trio/Trio Max
2.
Attach the second unit of
Trio/ Trio Max to the clips
*USB Cable omitted
3.5 THREE-SCREEN MODE
8

-Right click on your desktop while TRIO/TRIO
MAX Is connected and choose “Display
Setting”
-Then you should either see this screen or
the one at next Section
-If you have a duplicate screen and want to
change it to extend mode, click on the
“Duplicate these displays” from the drop
down box
-When the drop down box is opened,
choose “Extend these displays”
-Then click “Apply”
-Now you are in Extend Mode
4.1.1 WINDOWS SETTINGS
. DUPLICATE MODE TO EXTEND MODE
SECTION : DISPLAY SETTINGS
9