Mobilita M401 User manual

www.mobilita.in
TollFree : 1800 121 8485
Deluxe Aluminium
code : M401
Shower Commode Chair
www.mobilita.in
TollFree : 1800 121 8485

Place the two detachable arms into the four
locating holes – two each side of the commode.
Before use check for any signs of damage e.g.
cracked weld, flaking of paint, bent tube. If any signs
occur please contact your supplier to exchange and
refrain from using the product. DO NOT ATTEMPT TO
USE IF PRODUCT IS DAMAGED.
INSTRUCTIONS
Specifications
1. Introduction
Featuring soft feel polyurethane moulded seat and
upholstery for comfort, warmth and durability. Clip-on
building integrated seat easy for daily cleaning. Flip-up
armrest for easy transfer. Multi-use function as a
shower chair, commode or over a toilet pedestal. 4
aluminium 5” castors with brake. Swing away footrests.
2. Contents of the Box
Attendant Shower Commode Chair (T210)
Footplates (T210FOOT)
User Instructions (this leaflet)
3. Assembly Instructions
Carefully unpack and examine the product to
ensure it is complete.
Place the assembled base on a level floor. At
the rear of the commode you will see two black
threaded wheel nuts. Undo the wheel nuts so that the
locking holes are clear.
Place the two legs of the back into the
locating holes on the back edge of the commode
frame.
Secure the back by turning the black lock
nuts until you feel the nut biting against the leg of the
back. DO NOT OVERTIGHTEN -FINGER TIGHT IS
SUFFICIENT.•
Deluxe Aluminum
Shower Commode Chair Unit Weight 11 Kg
Weight Capacity 136 Kg
Width of handgrips 18”
Seat Area 18” – 17“
Seat Height 18.3” x 21.3”
Overall Dimensions 37.8” (L) x 21” (W)
Overall Dimensions Height 35.4”- 38.3”
Color Powder coated white

Place the two detachable arms into the four
locating holes – two each side of the commode.
Before use check for any signs of damage e.g.
cracked weld, flaking of paint, bent tube. If any signs
occur please contact your supplier to exchange and
refrain from using the product. DO NOT ATTEMPT TO
USE IF PRODUCT IS DAMAGED. 5. Maintenance Requirements
The product should be checked on a regular
basis for damage or wear and tear – this includes
flaking or cracking paint. Any undue signs of damage
should be noted and reported to the supplier in the
first instance. Should damage be evident, then the
user should refrain from using the product until advice
has been sought from the supplier.
It is recommended that all joints, abutments
and castors are sprayed with a water dispersing agent
such as WD40. This will give your commode greater
longevity and avoid premature rust.
4. Cleaning
Use mild detergent with warm water to wipe
down framework on at least a weekly basis more
frequently if required.
Do not use an abrasive cleaner as this will
damage the frame and nullify your warranty.
Ensure that all detergents are washed off
thoroughly.
Dry the product, paying particular attention
to all joints and abutments and that the frame
contains no trapped water.
Use of power/jet washing & industrial washing
machines:
If either of the above is used to clean equip-
ment care must be taken since high-pressure water
can be penetrative.
Care should be taken that frames are not
placed too close to high-pressure water jets.
After cleaning ensure any residual water is
removed from the framework as it could cause perma-
nent rusting of the frame (leave frames open in a warm
environment for several hours to ensure all internal
moisture evaporates).
We cannot offer advice on industrial washing
machines with regards to specific machine settings, as
these will be dependant on the manufacturer’s
instructions.
3. Assembly Instructions
Carefully unpack and examine the product to
ensure it is complete.
Place the assembled base on a level floor. At
the rear of the commode you will see two black
threaded wheel nuts. Undo the wheel nuts so that the
locking holes are clear.
Place the two legs of the back into the
locating holes on the back edge of the commode
frame.
Secure the back by turning the black lock
nuts until you feel the nut biting against the leg of the
back. DO NOT OVERTIGHTEN -FINGER TIGHT IS
SUFFICIENT.•
6. Warning
This product is intended for users of a
maximum of 136kg in weight.
We recommend a full risk assessment should
be carried out before use.
7. Disposal Instructions
Appropriate hygiene standards should be
applied before disposal to reduce the risk of infection.
Materials used are essentially non hazardous
and can be disposed of appropriately.

Warranty
Your Mobilita branded product is warrantied to be free
of defects in materials and workmanship for the
product of the original consumer purchaser.
This device was built to exacting standards and
carefully inspected prior to shipment. This Warranty is
an expression of our confidence in the materials and
workmanship of our products and our assurance to the
consumer of years of dependable service.
This warranty does not cover device failure due to
owner misuse or negligence, or normal wear and tear.
The warranty does not extend to non-durable compo-
nents, such as rubber accessories, casters, and grips,
which are subject to normal wear and need periodic
replacement.
If you have a question about your Mobilita device or this
warranty, please contact an authorized Mobilita dealer.
© 2017 Eternity Distribution Pvt. Ltd. All rights reserved
Mobilita is a trademark of
Eternity Distribution Pvt. Ltd.
Chennai, Tamil Nadu, India | Made in China for Mobilita
[email protected] | TollFree 1800 121 8485