Mobilita M301 Programming manual
www.mobilita.in
TollFree : 1800 121 8485
Drop-Arm Bedside
Commode with Padded Arms
code : M301
www.mobilita.in
TollFree : 1800 121 8485
Assembling Manual
Package Content : 2 parts of drop arm commode
frame, 2 pcs of connection tubes, 1 backrest, 1 splash
guard, 1 seat lid, 1 seat, 1 bucket with lid
01.
Remove contents from box. Depress brass push pins
and insert bucket frame section into first arm. The push
pins will snap into place when frame in securely in place.
Note: Make sure the back of the bucket frame (the side
with the back rest receptacles) corresponds to the back
of the armrest section.
02.
Repeat for second arm section.
03.
Insert backrest into backrest receptacles in commode
bucket frame. The brass push pins will snap into place
when secure.
Part# M301 - P1
Part# M301 - P3 Part# M301 - P4
Part# M301 - P2
04.
Align the padded toilet seat clamps onto the back
frame rail. (Both clamps should sit outside the pail brack-
ets). Push down on seat until clamps snap firmly into
place. To remove, grasp the back of the seat and lift
05. . Install commode bucket by dropping into bucket
frame. Reverse to remove.
Package Content : 2 parts of drop arm commode
frame, 2 pcs of connection tubes, 1 backrest, 1 splash
guard, 1 seat lid, 1 seat, 1 bucket with lid
01.
Remove contents from box. Depress brass push pins
and insert bucket frame section into first arm. The push
pins will snap into place when frame in securely in place.
Note: Make sure the back of the bucket frame (the side
with the back rest receptacles) corresponds to the back
of the armrest section.
02.
Repeat for second arm section.
03.
Insert backrest into backrest receptacles in commode
bucket frame. The brass push pins will snap into place
when secure.
04.
Align the padded toilet seat clamps onto the back
frame rail. (Both clamps should sit outside the pail brack-
ets). Push down on seat until clamps snap firmly into
place. To remove, grasp the back of the seat and lift
05. . Install commode bucket by dropping into bucket
frame. Reverse to remove.
Adjusting leg height
01.
Before use, adjust height of each leg to your specific
needs, making sure all legs are at the same height. When
desired height is reached, lock legs into place by aligning
buttons into proper holes, per illustration above.
02.
To be sure legs are locked into place by pushing down
on or by pulling legs.
Additional precautions
01.
Toilet seat must be in down position before use. Failure
to do so may result in breakage of commode and possible
injury.
02.
Do NOT install commode without first reading and
understanding this assembly and instruction sheet. If you
can not understand these instructions, contact a health-
care, dealer or technical professional before attempting to
install. Otherwise, injury or damage may occur.
03.
Inspect all parts for shipping damage before assembly.
If there is shipping damage - DO NOT USE. Contact
dealer/carrier for further instructions.
04.
Make certain that the height adjusting snap buttons
fully protrude through the same respective hole of each
leg extension. This will ensure that the leg extensions are
securely locked in position and an even height is achieved
(see Figure 1).
05.
Ensure ALL screws, nuts and/or bolts are tightened.
06.
Check the rubber tips on the leg extensions for rips,
wear or if they are are missing. Immediately replace any or
all if any of these imperfections exist.
07.
All four leg extensions with rubber tips MUST touch the
floor simultaneously at all times.
08.
Users with limited physical strength should be super-
vised or assisted while using commode.
© 2017 Eternity Distribution Pvt. Ltd. All rights reserved
Mobilita is a trademark of
Eternity Distribution Pvt. Ltd.
Chennai, Tamil Nadu, India | Made in China for Mobilita
Warranty
Your Mobilita branded product is warrantied to be free
of defects in materials and workmanship for the
product of the original consumer purchaser.
This device was built to exacting standards and
carefully inspected prior to shipment. This Warranty is
an expression of our confidence in the materials and
workmanship of our products and our assurance to the
consumer of years of dependable service.
This warranty does not cover device failure due to
owner misuse or negligence, or normal wear and tear.
The warranty does not extend to non-durable compo-
nents, such as rubber accessories, casters, and grips,
which are subject to normal wear and need periodic
replacement.
If you have a question about your Mobilita device or this
warranty, please contact an authorized Mobilita dealer.
01.
Toilet seat must be in down position before use. Failure
to do so may result in breakage of commode and possible
injury.
02.
Do NOT install commode without first reading and
understanding this assembly and instruction sheet. If you
can not understand these instructions, contact a health-
care, dealer or technical professional before attempting to
install. Otherwise, injury or damage may occur.
03.
Inspect all parts for shipping damage before assembly.
If there is shipping damage - DO NOT USE. Contact
dealer/carrier for further instructions.
04.
Make certain that the height adjusting snap buttons
fully protrude through the same respective hole of each
leg extension. This will ensure that the leg extensions are
securely locked in position and an even height is achieved
(see Figure 1).
05.
Ensure ALL screws, nuts and/or bolts are tightened.
06.
Check the rubber tips on the leg extensions for rips,
wear or if they are are missing. Immediately replace any or
all if any of these imperfections exist.
07.
All four leg extensions with rubber tips MUST touch the
floor simultaneously at all times.
08.
Users with limited physical strength should be super-
vised or assisted while using commode.
Table of contents
Other Mobilita Mobility Aid manuals
