MOBILUS C-MR BT User manual

User Manual of MOBILUS C-MR BT
external receiver

1. CONNECTING THE ADDITIONAL SWITCH / DRIVER
Wiring diagram of the module without a key switch - Fig. 1.1 . It is possible to connect an external
keyboard connector (without support) - Fig. 1.2 , bell connector - Fig. 1.3, control via a controller with
relay output - Fig. 1.4. They must be connected according to the attached diagram.
FIg. 1.1
L1
N
PE
N
PE
230V~ 50Hz
a
b
L1
N
PE
N
PE
230V~ 50Hz
a c
b
L1
N
PE
N
PE
230V~ 50Hz
a
b
L1
N
PE
N
PE
230V~ 50Hz
a c
b
c
Fig. 1.2
L1
N
PE
N
PE
230V~ 50Hz
a
b
L1
N
PE
N
PE
230V~ 50Hz
a c
b
L1
N
PE
N
PE
230V~ 50Hz
a
b
L1
N
PE
N
PE
230V~ 50Hz
a c
b
c
2

CONT.1. CONNECTING THE ADDITIONAL SWITCH / DRIVER
Fig. 1.3
L1
N
PE
N
PE
230V~ 50Hz
a
b
L1
N
PE
N
PE
230V~ 50Hz
a c
b
L1
N
PE
N
PE
230V~ 50Hz
a
b
L1
N
PE
N
PE
230V~ 50Hz
a c
b
c
Fig. 1.4
L1
N
PE
N
PE
230V~ 50Hz
a
b
L1
N
PE
N
PE
230V~ 50Hz
a c
b
L1
N
PE
N
PE
230V~ 50Hz
a
b
L1
N
PE
N
PE
230V~ 50Hz
a c
b
c
3

2. INTEGRATION WITH APPLE HOMEKIT
1. Make sure the accessory is turned on and nearby. The module will work properly with a
roller shutter that has end positions set.
2. On your iOS phone, open the Apple Home app, then press the “+” in the top corner of the
screen to add a new accessory.
3. Scan the HomeKit setup code (QR code) or, if you cannot scan it, select „I do not have or
cannot scan the code” and enter the 8-digit code.
4. After correctly entering the code, the window for adding the device to the house will appear.
After successful connection with the module, assign the device to the room in which it is
located and give it a name.
NOTE Integration with the Apple HomeKit system will enable voice control of devices using the
Siri voice assistant.
3. MODULE SOFTWARE UPDATE
To update the module, download the MOBILUS BT app from
the AppStore.
The MOBILUS BT app will automatically search for all
MOBILUS BT modules within the Bluetooth range of your
smartphone.
1. In the MOBILUS BT application, press on the device panel to open SETTINGS.
2. Select the SOFTWARE UPDATE item, and then check the availability of the new software version of
the device.
4

4. ENTRY INTO THE MODULE PROGRAMMING MODE
Press and hold a programming button on module MOBILUS
C-MRBT above 5 sec until the connected actuator executes one
sequence of noticeable and audible micro movements down / up
confirming the entrence of the receiver in the PROGRAMMING
MODE.
WARNING! If within 20 seconds no programming will be
performed, the MOBILUS C-MRBT radio module automati-
cally exits from the programming mode. Connected actuator
executes one sequence of noticeable and audible micro
movements down / up.
1 s.
BEEP! BEEP!
PILOT 2
1 s.
b
5 s.
5. RESETOWANIE MODUŁU DO USTAWIEŃ FABRYCZNYCH
1. Enter the PROGRAMMING MODE for the MOBILUS C-MRBT module - Fig. 5a.
2. In the PROGRAMMING MODE, press and hold the programming key above 5 seconds - Fig.
5b. The module is removed from the HomeKit network and all remote controls previously
loaded into the module are deleted from its memory, as confirmed by a single white LED
flash.
Fig. 5
a b
5

6. CHANGE THE DIRECTION OF OPERATION OF THE ACTUATOR BY SWAPPING WIRES
1. If you press the UP direction button in the application, and the armor goes DOWN, you need
to change the direction of rotation of the drive. To do this, swap the order of the UP and
DOWN wires - Fig. 6a.
Fig. 6
L1
N
PE
N
PE
230V~ 50Hz
a
L1
N
PE
N
PE
230V~ 50Hz
a c
b
L1
N
PE
N
PE
230V~ 50Hz
a
b
L1
N
PE
N
PE
230V~ 50Hz
a c
b
c
7. CHANGING THE MODULE’S OPERATING MODE
ATTENTION! The module works in roller shutter mode by default, but you can change its mode of
operation to support lighter matrerial roller shutters such as screens.
Roller shutter operation mode:
1. Press the button on the module 3 times - the module will give 2 beeps and enter the roller shutter
operation mode - Fig. 7a.
Screen operation mode:
1. Press the button on the module 3 times - the module will beep 1 time and enter screen handling
mode - Fig. 7b.
6

CONT. 7. CHANGING THE MODULE’S OPERATING MODE
Fig. 7
ba
BEEP! BEEP! BEEP!
8. CHANGING THE MODE OF OPERATION OF THE CONTROL BUTTONS
The MOBILUS C-MRBT module allows you to change the operating mode of the control
buttons.
I. MODE WITH HOLD UP - Pressing the key causes the roller shutter to be lowered or raised.
II. MODE WITHOUT HOLD UP - Lowering or raising the controlled roller shutter continues as
long as the control key is pressed.
To change the operation mode of the control buttons:
1. Enter the module into PROGRAMMING MODE - Fig. 8a.
2. On the switch, press the DOWN button - Fig. 8b. The module will go into non-supported
mode. Repeating the procedure will cause the module to go into a sustained mode.
Fig. 8
a b
a b
a b
7

9. ENABLE / DISABLE OVERLOAD DETECTION
MOBILUS C-MRBT transmits information to remotes about overload - for example, it may be
related to a housing lock occurring at the time of raising or lowering. Mode is factory-setted - it
is possible to turn off.
To do so:
1. Enter the module into PROGRAMMING MODE - Fig. 9a.
2. On the switch, press the UP button - Fig. 9b. Overload detection is disabled, to restore this
function the procedure must be repeated.
Fig. 9
a b
a b
a b
8

OPERATING THE MODULE WITH THE COSMO REMOTE CONTROL
1. LOADING THE MASTER-A * CODE TO THE RECEIVER MEMORY
1. Enter the MOBILUS C-MRBT PROGRAMMING MODE.
2. Press and hold the STOP and UP buttons
simultaneously on the remote control until the connected
actuator executes one sequence of noticeable and audible
micro movements down / up. The MASTER-a code has been
loaded into memory and the module goes to the WORK
MODE. Now, with the MASTER remote control, you can
operate the units or enter the PROGRAM MODE to load
more remote controls.
BEEP! BEEP!
PILOT 2
1 s.
b
5 s.
BEEP! BEEP!
WARNING In the case of a multi-channel remote control
select only one channel to be MASTER.
NOTE For the convenience of programming, it is recom-
mended that each COSMO | C-MRBT module had its own
separate MASTER (remote control (separate channel for
multi-channel remotes). Avoid situations where several
COSMO | C-MRBT modules remote controls will have
common MASTER (shared channel).
BEEP! BEEP!
MASTER
1 2 3 4 5
5 s.
BEEP! BEEP!
PILOT 2
1 s.
a b
1 2 3 4 5 1 2 3 4 5
*MASTER - remote control or channel (in the case of a multi-channel remotes) loaded first into
the memory of the MOBILUS C-MRBT module. Allows you to program further remote controls.
99

2. PROGRAMMING OF THE SECOND AND EVERY OTHER REMOTE CONTROL
1. On the MASTER remote control, simultaneously press and hold the STOP and UP until the
connected actuator executes one sequence of noticeable and audible micro movements down / up
confirming the entrence of the receiver in the PROGRAMMING MODE - Fig. 2a.
2. On the second remote control (for the multi-channel remote control, select the channel
you want to program), press and hold both STOP and UP buttons simultaneously, until the
connected actuator performs one sequence of noticeable and audible micro movements
down / up. The remote (channel) was loaded into the receiver’s memory - Fig. 2b.
Fig. 2
MASTER PILOT 2a b
Repeat step 2 to load the next remote control. If, however, no programming operation is started
within 20 seconds, the module automatically returns to operating mode. Return to operating
mode can also be performed manually using MASTER. In such a situation, press and hold the
STOP and UP MASTER buttons. In both cases, the return to operating mode will be confirmed
by a single sequence of micro movements down / up of the connected actuator.
10