Mode Lighting SceneStyLED4 User manual

For more information please visit
www.modelighting.com
User Guide

Contents
INTRODUCTION________________________________________
Product Key Features
Before you Start
Safety Notice
USING YOUR SCENE STYLED____________________________
Operation:
Scene Mode
Impulse Mode
Scene Editing:
Adjusting Scene/Circuit Brightness
Adjusting Fade Time
Advanced Scene Editing:
Including/Excluding Circuits
Setting Button LED Colours
Holiday Mode
Fault Detection
CONFIGURATION_______________________________________
Main Configuration Menu:
Factory Restore
Operation Configuration Menu:
Selecting Operating Mode
Toggling to a Defined Level
Power Cut Restore
Button LEDs Dim when Inactive
Infrared Enable/Disable
Circuit Configuration Menu:
Selecting a Circuit to Edit
Maximum/Minimum Brightness
Toggle level
Switched
Advanced Circuit Configuration Menu:
Boost
Dim Mode
Shutdown Enable/Disable
Remote Switch Configuration Menu:
INSTALLATION__________________________________________
Important Safety Note
Specifications
Installing SceneStyle/Remote Switches
Installing/Removing Fascia
Testing
MENU DIAGRAMS_______________________________________
TROUBLESHOOTING___________________________
2
2
2
2
3-9
3-4
3
4
5-6
5-6
6
6
6
7
8-9
9
10-18
10
10
11
11
11
11
11
11
12-13
12
12-13
13
13
14
14
14
14
14-18
19-24
19
20
21-22
23
24
25-28
29
1

Introduction
PRODUCT KEY FEATURES:
•Four circuits of trailing edge dimming
•Operation in either Scene or Impulse mode
• Six editable scenes with selectable scene fade times
• Master raise and lower of overall brightness
•Multiple configuration options to ensure compatibility with a variety of light fittings.
• User selectable button colours
•Four configurable multi-function remote switch inputs
•Holiday mode to simulate occupancy
•Optional IR remote control
•Various fascia plate finishes available
BEFORE YOU START:
Once installed, SceneStyle will operate with default values without further setup.
By default, SceneStyle is configured to work with many different light fittings, which
may cause some light fittings not to dim as low as expected or at all.
With certain fittings, it is possible to achieve a lower minimum brightness than the
default value. To decrease the minimum circuit brightness, see entering the
configuration menus (p.10) and follow the instructions to enter the circuit
configuration menu.
If lights fail to turn on at minimum brightness, boost mode may be required. Refer
to the troubleshooting guide for further guidance.
It is normal for the fascia plate to become warm during operation.
SAFETY NOTICE:
•SceneStyle must be installed by a qualified electrician or other competent person.
Installation should be in accordance with the National Wiring Regulations or other
applicable regulations. Compliance with the EC EMC or Low Voltage Directives may be
invalidated if not used or installed to the published specification.
•Isolate (turn off) the mains power at the main consumer unit (fuse box) before installation
or any maintenance, including changing blown light fittings.
•Read the Installation instructions and safety notes in full prior to installation.
2

Operation
3
OPERATING MODES:
SceneStyle has two modes of operation, Scene and Impulse. By default, SceneStyle operates
in Scene Mode.
What is a scene?
A scene is a selection of circuits which can be set to individual light levels with a single
button press. One circuit might for example control wall lights, a second ceiling lights and a
third a table top light fitting. This allows combinations of light levels to be created for
different activities, such as watching TV, reading or entertaining.
Scene operation
•Each scene can be selected by pressing its respective button.
•Use the raise and lower buttons to collectively raise and lower the brightness of the scene.
By default, SceneStyle is configured so that every light fitting connected will dim to a
percentage of its full brightness depending on the scene selected:
The default fade time for all scenes is 2 seconds.
SCENE 1
SCENE 2
SCENE 3
SCENE 4
ON SCENE
RAISE
LOWER
OFF SCENE
SCENE 1 2 3 4 ON OFF
BRIGHTNESS 80% 60% 40% 30% 100% 0%

Operation
4
What is Impulse?
Impulse is an alternative mode of operation where the brightness of each circuit is controlled
individually using its own button.
Impulse operation
•A short press of buttons 1-4 will switch the respective circuit on and another press will
switch it off.
•Holding a circuits respective button will raise or lower the brightness of that circuit. The
direction of dimming can be reversed by first releasing and then holding the button again.
•The raise and lower buttons can be used to collectively adjust the brightness of all the
circuits which are currently on.
•To turn off every circuit, the off button can be pressed.
To change to Impulse operation, see Entering the configuration menus (p.10), followed by the
Operation configuration menu (p.11).
Factory restore resets every scene, colour and setting to the factory defaults. Once complete,
SceneStyle will automatically return to the main screen. To do this, see Entering the
configuration menus, followed by Factory restore (p.10).
CIRCUIT 1
CIRCUIT 2
CIRCUIT 3
CIRCUIT 4
ON
RAISE
LOWER
OFF
Factory Restore

Scene Editing
5
ENABLING SCENE EDITING:
Scenes can be edited up to an hour after power up. After this time, scene editing can be
reenabled by holding the bottom two buttons for one second until they are lit red, then
waiting five seconds for SceneStyle to return to the main screen.
Once you are returned to the main screen, scene editing will be allowed for one hour.
To select a scene to edit, the scenes respective button must be held for five seconds. Once selected,
the button will flash blue. All changes made whilst scene editing are saved automatically.
Adjusting Circuit Brightness
Once the scene to edit has been selected, select the circuit to adjust by briefly pressing that
circuits respective button. The button will illuminate brighter to show the circuits brightness
can now be adjusted using the raise and lower buttons.
By default, SceneStyle is configured so that every light fitting connected will dim to a percentage
of its full brightness depending on the scene selected:
In this example, scene 1 has
been selected for editing.
Here, circuit 3 is being
adjusted in scene 1.
Editing a Scene

Scene Editing
6
Adjusting Scene Brightness
The brightness of a selected scene can be adjusted by pressing the top right button to select
all circuits. The button will illuminate brighter to show scene brightness can now be adjusted
using the raise and lower buttons.
Adjusting Fade Time
To change the fade time for the scene being edited, hold the top two buttons for one second. The
time taken to change between the previous scene and the scene being edited can then be selected.
Finishing Scene Editing
When finished editing the scene, press the exit button to return to the main screen where
another scene can be selected for editing if required.
Including/Excluding Circuits
Only circuits included in a scene are affected when the scene is selected. Consequently, a circuit
not included in a scene will remain at its current brightness, even when that scene is selected.
Circuits illuminated green are included in the scene, whereas those illuminated red are not.
To change whether a circuit is included in a scene, hold that circuits respective button for
more than one second and then whilst still holding the button, select the include or exclude
button to include or exclude the circuit.
This shows every circuit being
adjusted equally in scene 1.
In this example, circuit 3 is excluded,
whilst 1, 2 and 4 are included.
Advanced Scene Editing

Setting Button LED Colours
7
SETTING YOUR BUTTON COLOURS:
The foreground and background colour of the buttons can be selected to suit the user.
• When in Scene Mode, the foreground colour shows the selected scene, whereas in
Impulse, it shows which circuits are on.
• The background colour is the colour displayed at any other time.
•The ON/OFF buttons can be fixed green and red respectively.
From the main screen, hold the top two buttons for five seconds. Foreground colour can
then be selected, followed by background colour and finally whether the ON/OFF buttons
should use the selected colours, or be fixed green and red.

Holiday Mode
8
Holiday Mode Operation
SceneStyle can switch light fittings on and off automatically to simulate occupancy over a
period of 24 hours. Holiday mode will run repeatedly, running the first step at the same time
every day.
Entering Holiday Mode
From the main screen, hold the top right and bottom right buttons for five seconds.
Setting the Start Time
• To set the start time, first decide the time at which the first step should begin. The
sequence is designed to start at around 6pm so that illumination occurs from 6pm-12pm
and from 6.30am to 9am.
• Work out how many hours there are between the current time and the time at which the
first step should begin. This is the required time delay.
•Enter the time delay into SceneStyle using any combination of the 5 pre-programmed
time delays provided. Selected buttons contributing to the time delay are lit yellow.
STEP TIME SCENE SELECTED
1Start time On
2 Start time + 30mins 1
3 Start time + 1hr, 30mins 2
4 Start time + 3hrs, 30mins 3
5 Start time + 6hrs Off
6 Start time + 12hrs, 30mins 3
7 Start time + 13hrs On
8 Start time + 15hrs Off

Holiday Mode
9
Enabling/Disabling Holiday Mode:
• Press the top right button to begin holiday mode. Holiday mode will run repeatedly,
running the first step at the same time every day. Whilst in holiday mode, the current
scene will be lit red and every button will flash green.
• To exit Holiday Mode, press any button.
Fault Detection and Shutdown Circuity
SceneStyle contains fault detection and shutdown circuitry which will prevent damage due
to short circuit or circuit overload. If a circuit is faulty, the circuits respective button will flash
red. Faulty circuits will be restarted automatically once the fault has been resolved.
In this example, the +1 HRS, +4 HRS and +12 HRS buttons
have all been selected. Therefore, the total time delay is +17
HRS. If the current time was 1:00am, the first step of holiday
mode would begin at 6:00 pm that evening. Subsequently, step
2 would start at 6:30pm, step 3 at 7:30pm and so on. The cycle
would begin again at 6:00pm the following day.
Fault Detection

Configuration Menus
10
UNDERSTANDING THE CONFIGURATION MENU
The configuration menus can be used to configure advanced features of SceneStyle. To return
to the main screen at any point, press the bottom right button repeatedly until the main
screen appears. For experienced users, a complete diagram of the configuration menus is
provided at the back of the manual.
Entering The Configuration Menus
To enter the main config menu, hold the bottom two buttons for one second until they are lit
red. Release the bottom two buttons and then press buttons two and one alternately in the
pattern 2, 1, 2, 1 to enter the menu.
MAIN CONFIGURATION MENU
The main config menu can be used to perform a factory restore and to access the three
further configuration menus.
Factory Restore
Factory restore resets every scene, colour and setting to the factory defaults. To perform a factory
reset, hold the factory restore button for five seconds. The button can be released once all buttons
start flashing yellow. Once complete, SceneStyle will automatically return to the main screen.

Operation Configuration Menu
11
OPERATION CONFIGURATION MENU
The operation configuration menu can be used to configure options related to the operation
of SceneStyle itself. To enter the operation config menu, press the operation button on the
main configuration menu. To return to the main configuration menu, press the return button.
Selecting Operating Mode
To choose between Scene and Impulse mode, briefly press the mode button. When lit purple,
SceneStyle is in Scene mode. For descriptions of both Scene and Impulse mode, see the
Operation section (p.3).
Toggling to a Defined Level
Circuits can be configured to always return to a defined light level when turned on, rather
than returning to the level at which the circuit was previously operating. To select whether to
toggle to a defined light level, press the defined toggle button. When the button is lit green,
all circuits will toggle to a defined level when switched on. To set this level, see Toggle level
in the circuit configuration menu (p.13).
Power Cut Restore
After a power cut, the lighting circuits can be set either to return to their previous light levels
or to remain off. To select which action is taken, press the power cut restore button. When lit
green, the circuits are set to return to their previous light levels.
Button LEDs when inactive
It is possible to dim the button LEDs after a period of inactivity. This may be desirable if
SceneStyle is being used in a dark room, where the button LEDs may be distracting. To select
whether the LEDs dim, briefly press the LEDs dim when idle button. When lit green, the LEDs
are set to dim when SceneStyle is inactive.
Infrared Enable / Disable
If other remotes are causing undesired selection of circuits or scenes, the remote-control
feature of SceneStyle can be disabled. To do this, briefly press the infrared button. When lit
green, the remote-control functionality is enabled.

Circuit Configuration Menu
12
CIRCUIT CONFIGURATION MENU
The circuit configuration menu is used to adjust settings which affect the operation of lighting
circuits. To enter the circuit config menu, press the circuit button on the Main config menu.
To return to the previous screen at any point, press the return button.
Selecting a Circuit to Edit
To edit a circuit, press that circuits respective button. The screen will change to show the
options which can be adjusted for the circuit.
Maximum Brightness
To adjust maximum circuit brightness, first briefly press the maximum brightness button, which will
lead to a second menu being displayed. The maximum light level can then be adjusted using the
raise and lower buttons.

Circuit Configuration Menu
13
Minimum Brightness
With compatible light fittings, it may be possible to reduce the minimum circuit brightness,
although incompatible fittings may begin to flicker at lower light levels. To reduce this
brightness, first briefly press the minimum brightness button which will lead to a second
menu being displayed. The minimum light level can then be adjusted using the raise and
lower buttons.
Toggle Level
Toggle level can only be adjusted if SceneStyle is configured to toggle to a defined light level.
To configure SceneStyle to toggle to a defined light level, see Entering the configuration
menus (p.10), followed by the Operation configuration menu (p.11).
Toggle level is the light level to which circuits will be set if SceneStyle has been configured to
toggle to a defined light level. To adjust toggle level, first briefly press the toggle level button,
which will lead to a second menu being displayed. The toggle level can then be adjusted by
using the raise and lower buttons.
Switched
A circuit which is set to switched cannot be dimmed to different light levels and will therefore
operate as if controlled by a normal on/off switch. To change a circuit between being dim-
mable and switched, briefly press the switched button. When lit green, the circuit is switched
and cannot be dimmed.

Advanced Circuit Configuration
14
ADVANCED CIRCUIT CONFIGURATION
Briefly pressing the advanced button displays the second page of the circuit configuration
menu, which gives further circuit options.
Boost
Some light fittings might not turn on to a low light level, despite being able to operate at that
light level during normal operation. One of two levels of boost can be chosen to ensure light
fittings always turn on by pressing the boost button.
Dim Mode
Changing the dim mode can improve the dimming of some types of light fittings. This setting
should only be changed if issues are being experienced.
Shutdown Enable / Disable
The shutdown button can be used to disable SceneStyle’s protection circuitry, although this is not
recommended unless the protection circuitry is causing an issue. When the shutdown enable
button is lit green, the shutdown circuitry is active and SceneStyle is protected from circuit faults.
REMOTE SWITCH CONFIGURATION MENU
The remote switch configuration menu is used to set up SceneStyle’s four remote switch inputs. To
enter the remote switch config menu, press the remote switches button on the main config menu.
To return to the previous screen at any point, press the return button.
Remote Switch Configuration Menu

Remote Switch Configuration Menu
15
REMOTE SWITCH CONFIGURATION MENU - CONTINUED
Step 1 - Choosing a switch input to configure
To choose a switch input to configure, press that inputs
respective button.
Step 2 - Selecting Switch Type
Tell SceneStyle the type of switch which has been
connected. The remote switch input being configured
will flash red.
You will now be required to select a two digit code which determines the function of the
switch. This code is selected in Steps 3 and 4 on the following page. You will then be
required to enter this code in Step 5.
SWITCH TYPE DESCRIPTION COMMON USES
Momentary
Switch
Triggers an action each
time it is pressed. Impulse dimming
Latching Switch
(Alternate Action)
Triggers an action
each time the switch
is moved to a new
position.
Two-way switching
Latching Switch
(Defined Action)
Triggers the same
action when switched
off and the same
action when switched
on.
A defined action
switch can be
labelled with its
functions.
Contact
Closure
Triggers when the
contact is closed.
PIR
Contact
Opening
Triggers when the
contact is opened.

Remote Switch Configuration Menu
16
Step 3 - Selecting Switch Type
Pick a compatible function for the chosen switch type and note the relevant table number.
FUNCTION
SWITCH TYPE
TABLE
Momentary Latching
(Alternate)
Latching
(Defined)
Contact
Closure
Contact
Opening
Two way switching
of one or more
circuits*
P P O P P 1
Toggle between
two nominated
scenes
P P P P P 2
Toggle between
nominated scene
and previous scene
P P O P P 3
Selection of
nominated scene P P P P P 4
Impulse control
of one or more
circuits
P O O O O 5
Special functions Function Dependent 6
Keycard O O P O O 7

Remote Switch Configuration Menu
17
Step 4 - Use The Table Number to choose affected Circuits / Scenes:
Two way switching of one or more
circuits
Circuits Affected Code
Respective circuit 11
All circuits 12
Circuits 1 and 2 13
Circuits 1 and 3 14
Circuits 1 and 4 15
Circuits 2 and 3 16
Circuits 2 and 4 17
Circuits 2, 3 and 4 18
Toggle between two nominated
scenes
Nominated Scenes Code
Off Scene and On Scene 21
Off Scene and Scene 1 22
Off Scene and Scene 2 23
Off Scene and Scene 3 24
Off Scene and Scene 4 25
On Scene and Scene 3 26
On Scene and Scene 4 27
Scene 1 and Scene 4 28
Toggle between nominated scene
and previous scene
Nominated Scene Code
Off Scene 31
On Scene 32
Scene 1 33
Scene 2 34
Scene 3 35
Scene 4 36
Recall of nominated scene
Nominated Scene Code
Off Scene 41
On Scene 42
Scene 1 43
Scene 2 44
Scene 3 45
Scene 4 46
Table 1 Table 2
Table 3 Table 4

Remote Switch Configuration Menu
18
Step 5 - Enter the Two-digit Code from Step 4:
Example Code 46
Once your two-digit code has been entered, you will automatically be returned to Step 1.
Impulse Control of one or more
circuits
Circuits affected Code
Respective circuit 51
All circuits 52
Circuits 1 and 2 53
Circuits 1 and 3 54
Circuits 1 and 4 55
Circuits 2 and 3 56
Circuits 2 and 4 57
Circuits 2, 3 and 4 58
Special functions
Function Switch Type Code
Last man out
(If the current
scene is off,
select the on
scene, other-
wise select the
off scene)
Push Button,
Rocker Switch
(Alternate
Action), Contact
Closure, Contact
Opening
61
Table 5 Table 6
Keycard – Disables SceneStyle
whilst keycard removed
Scenes selected Code
On scene on entry, off scene on exit 71
Scene 1 on entry, off scene on exit 72
Scene 2 on entry, off scene on exit 73
Scene 3 on entry, off scene on exit 74
Scene 4 on entry, off scene on exit 75
Off scene on exit 76
Table 7

Installation
19
IMPORTANT SAFETY NOTES:
•Isolate (turn off) the mains power at the main consumer unit (fuse box) before commencing
installation or performing any maintenance, including changing blown light fittings.
•SceneStyle is designed to control light fittings at mains voltage or low voltage when fed
from a suitable electronic transformer. To avoid hazard or possible damage do not use with
inductive, fluorescent, wire wound transformer or motor loads.
•SceneStyle must be installed by a qualified electrician or other competent person.
Installation should be in accordance with the National Wiring Regulations or other applicable
regulations. Compliance with the EC EMC or Low Voltage Directives may be invalidated if
not used or installed to the published specification.
•SceneStyle is for installation to 230V and 240V single phase mains supplies only. The cable
connected to the live input terminal must be capable of supplying the total current for all
circuits (4A maximum).
•SceneStyle must be protected by an external circuit breaker or fuse rated at 6A maximum.
•SceneStyle is a Class 1 product. This unit must be earthed.
•SceneStyle must be installed in a suitable UK double gang backbox, compliant to BS4662
or BS5733. We recommend that a 47mm depth backbox is used.
•SceneStyle complies with EN60669-1/EN60669-2-1, EN55015 and EN61547.
•For indoor use only, at temperatures between 0°C and +25°C
•Do not operate without the front fascia plate correctly fitted.
•SceneStyle is suitable for 12V halogen lamps using only electronic transformers and not
wire wound or toroidal. Suitable electronic low voltage lighting transformers are manufactured
by Mode Lighting Ltd. Please contact your SceneStyle stockist regarding the correct product
for your installation. You may connect 240V GLS and GU10 light fittings to SceneStyle.
•SceneStyle’s circuits will shut down if short-circuited or overloaded. This is indicated by the
circuits respective button flashing red.
•The fascia will become warm during operation. This is normal.