Modern Fan Co Stella User manual

MODERN FAN COMPANY
Customer Service
M-F 8am - 4pm (PST)
(ph) 888.588.3267
www.modernfan.com
(1) Remove and identify contents of carton.
Stella Fan- Installation instructions
Should you have any questions or difficulty installing your new fan,
please contact Modern Fan Co. customer service immediately.
Note: Power supply must be turned off prior to any contact with electrical
wires. It is recommended that a licensed electrician be hired to install your
ceiling fan.
Stella
canopy
blades
lower
assembly
diffuser
socket
optional
control
upper assembly
half ball
down rods
hanging
bracket
balancing
kit
hardware
package
(2) Using machine screws and washers from
hardware package or existing screws and washers
in junction box, securely attach hanging bracket to
ceiling junction box.
(3) Remove stopper pin and half ball from small
down rod by loosening set screw on half ball. Set
parts aside for reinstallation in step (7).
stopper pin
set screw

(4) Remove the stopper screw and loosen the set
screw on the fan collar. Set the stopper screw
aside for step (5).
set screw
(6) Slide fan canopy over down rod and carefully
rest on top of fan body.
canopy
(7) Reinstall half ball from step (3) on end of down
rod. Be sure that stopper pin is inserted through
down rod and seated in half ball. Tighten set
screw against down rod.
stopper pin
set screw
(5) Run fan wires through selected down rod.
Reinstall stopper screw from step (4) and firmly
tighten set screw on fan collar against down rod.
Note: If ceiling height allows, using a longer down
rod will increase airflow and efficiency.
stopper screw
(8) Lift fan to ceiling and set half ball in the
hanging bracket so that the ridge on the edge of
the hanging bracket is seated in the slotted
channel in the half ball.
(10) Loosen set screws on the sides of the
hanging bracket. Lift canopy to ceiling. Align slots
on side of canopy with set screws on hanging
bracket, rotate canopy and tighten set screws to
hold canopy in place.
set screw
(11) Using blade screws from hardware package,
secure blade to blade arm. Start all three screws
before completely tightening. Repeat for all four
blades.
(9) With fan safely suspended by bracket, make wire connections with wire
nuts included in hardware package as described in the Control Installation
Instructions. If using optional #003, #004 or #005 controls, the receiving
unit should be placed inside the arms of the hanging bracket and
connected at this time.

(12) Follow steps (a) through (d) to install socket and lamp:
(a) Remove socket
bracket screws (two)
and set aside for
step (c).
(c) Attach socket to
fan with screws from
step (a). Tuck wire
between socket
bracket legs (away
from lamp).
(c) Insert lamp:
75W G-9 or
26W GU-24 CFL
Note: Do not touch
G9 lamp with bare
fingers.
(b) Connect wire
leads from socket to
wire leads from fan.
(17) Install optional wall control as described in the control installation
instructions.
(19) The rotor and motor of your fan have been dynamically balanced at the
factory. In addition, the blades have been matched to the nearest gram to
ensure a well balanced ceiling fan. Furthermore, a blade balancing kit has
been included with your fan. Please refer to the instructions packaged with
the balancing kit should your fan require additional balancing.
(18) Your fan is reversible for summer and winter
operation. The reverse switch is located on the
top of the fan body. When reading the REVERSE
label, the LEFT position is for summer and the
RIGHT position is for winter.
reverse switch
(13) Loosen (but don’t remove) all three diffuser
screws on lower assembly so that the glass diffuser
can be inserted.
(14) Insert glass diffuser and tighten the three
diffuser screws to secure to lower assembly. The
rubber gasket around the neck of the diffuser may
need to be adjusted or repositioned in order for the
diffuser to insert fully into the metal fitting.
diffuser screws
(15) Align tabs on lower
ring assembly with slots in
upper assembly and rotate
clockwise to attach. Pull
on outside edges of upper
and lower assembly to
ensure a snug fit.
(16) In order to align posts on upper and lower
ring assemblies, loosen three adjustment screws
on upper assembly. Rotate upper assembly until
posts are aligned with lower posts. Then tighten
adjustment screws to secure in place.