Modular 316715 User manual

UK
RANGE, GAS SOLID TOP
Installation-Use-Maintenance
FR
FORNEAUX, PLAQUES COUP-DE-FEU A GAZ
Installation-Emploi-Entretien
DE
HERDE, GASBEHEIZTE GLÙHPLATTENHERDE
Installation-Gebrauch-Wartung
NL KEUKENS, GRILLPLATEN GAS
Installatie-Gebruik-Onderhoud
MOD.
_70/40 PCG…
_70/70 PCG…
_70/110 PCG…
_70/70 CFG…
_70/70 CFGE…
_70/110 CFG…
_70/110 CFGE…
_70/70 TPG…
_70/70 TPPCG…
_70/110 TPPCG2…
_70/70 TPFG…
_70/70 TPPCFG
_70/110 TPFG…
_70/110 TPPCFG2
_70/40 PCE…
_70/70 PCE…
_70/70 CFE…
_65/40 PCG-D
_65/80 PCG-D
_65/40 PCE-D
_65/70 PCE-D
Doc.n°
252.442.00
Edition
03
modular gassolidtop700-900 G23M 1/80

UK - INSTALLATION –USE - MAINTENANCE .............................................................................................................................. 20
I. GENERAL PRESCRIPTIONS .........................................................................................................................................................................04
1. DISPOSAL OF PACKING AND OF THE APPLIANCE .......................................................................................................................................................... 04
2. SAFETY DEVICES............................................................................................................................................................................................................ 05
II. INSTRUCTIONS FOR INSTALLATION ...........................................................................................................................................................05
3. REMINDERS FOR THE INSTALLER.................................................................................................................................................................................. 05
4. REFERENCE STANDARDS AND LAWS ............................................................................................................................................................................ 05
5. UNPACKING.................................................................................................................................................................................................................. 05
6. POSITIONING................................................................................................................................................................................................................ 06
7. CONNECTIONS.............................................................................................................................................................................................................. 06
8. CONVERSION TO ANOTHER TYPE OF GAS..................................................................................................................................................................... 07
9. COMMISSIONING ......................................................................................................................................................................................................... 08
III. INSTRUCTIONS FOR USE ............................................................................................................................................................................09
10. REMINDERS FOR THE USER .......................................................................................................................................................................................... 09
11. USING THE GAS HOB .................................................................................................................................................................................................... 09
12. USING THE HOTPLATE/SIMPLE SERVICE ....................................................................................................................................................................... 10
13. USING THE GAS OVEN .................................................................................................................................................................................................. 10
14. USING THE ELECTRIC HOB ............................................................................................................................................................................................ 11
15. ELECTRIC CONVECTION OVEN USE ............................................................................................................................................................................... 11
16. ELECTRIC STATIC OVEN USE (900 SERIES) ..................................................................................................................................................................... 12
17. PROLONGED DISUSE..................................................................................................................................................................................................... 13
IV. INSTRUCTIONS FOR CLEANING..................................................................................................................................................................13
18. REMINDERS FOR CLEANING ......................................................................................................................................................................................... 13
V. INSTRUCTIONS FOR MAINTENANCE..........................................................................................................................................................13
19. REMINDERS FOR THE MAINTENANCE TECHNICIAN...................................................................................................................................................... 13
20. CONVERSION TO ANOTHER TYPE OF GAS..................................................................................................................................................................... 14
21. COMMISSIONING ......................................................................................................................................................................................................... 14
22. TROUBLESHOOTING ..................................................................................................................................................................................................... 14
23. REPLACING COMPONENTS ........................................................................................................................................................................................... 15
24. CLEANING THE INTERIOR.............................................................................................................................................................................................. 15
25. MAIN COMPONENTS.................................................................................................................................................................................................... 16
FR - INSTALLATION –EMPLOI - ENTRETIEN ............................................................................................................................... 18
I. AVERTISSEMENTS GÉNÉRAUX...................................................................................................................................................................18
1. ÉLIMINATION DE L'EMBALLAGE ET DE L'APPAREIL....................................................................................................................................................... 19
2. DISPOSITIFS DE SÉCURITÉ............................................................................................................................................................................................. 19
II. INSTRUCTIONS POUR L'INSTALLATION......................................................................................................................................................19
3. AVERTISSEMENTS POUR L'INSTALLATEUR.................................................................................................................................................................... 19
4. NORMES ET TEXTES DE LOI DE RÉFÉRENCE .................................................................................................................................................................. 20
5. DÉBALLAGE...................................................................................................................................................................................................................20
6. MISE EN PLACE .............................................................................................................................................................................................................20
7. RACCORDEMENTS ........................................................................................................................................................................................................20
8. ADAPTATION À UN AUTRE TYPE DE GAZ ...................................................................................................................................................................... 21
9. MISE EN SERVICE ..........................................................................................................................................................................................................22
III. INSTRUCTIONS POUR L'UTILISATION.........................................................................................................................................................23
10. AVERTISSEMENTS POUR L'UTILISATEUR....................................................................................................................................................................... 23
11. UTILISATION DU PLAN DE CUISSON AU GAZ................................................................................................................................................................. 23
12. UTILISATION DE LA PLAQUE COUP-DE-FEU À GAZ/ SIMPLE SERVICE............................................................................................................................ 40
13. UTILISATION DU FOUR À GAZ....................................................................................................................................................................................... 25
14. UTILISATION DU PLAN DE CUISSON ÉLECTRIQUE ......................................................................................................................................................... 26
15. MODE D’EMPLOI DU FOUR ÉLECTRIQUE À CONVENTION ............................................................................................................................................ 26
16. MODE D’EMPLOI DU FOUR ÉLECTRIQUE STATIQUE ..................................................................................................................................................... 26
17. PÉRIODES D'INACTIVITÉ................................................................................................................................................................................................ 27
IV. INSTRUCTIONS POUR LE NETTOYAGE........................................................................................................................................................27
18. AVERTISSEMENTS POUR LE NETTOYAGE ...................................................................................................................................................................... 27
V. INSTRUCTIONS POUR L'ENTRETIEN ...........................................................................................................................................................28
19. AVERTISSEMENTS POUR LE TECHNICIEN D'ENTRETIEN ................................................................................................................................................ 28
20. ADAPTATION À UN AUTRE TYPE DE GAZ ...................................................................................................................................................................... 28
21. MISE EN SERVICE..........................................................................................................................................................................................................28
22. RÉSOLUTION DES DYSFONCTIONNEMENTS.................................................................................................................................................................. 28
23. REMPLACEMENT DE PIÈCES.......................................................................................................................................................................................... 30
24. NETTOYAGE DES PIÈCES INTERNES............................................................................................................................................................................... 31
25. PIÈCES PRINCIPALES ..................................................................................................................................................................................................... 31
DE - INSTALLATION –GEBRAUCH - WARTUNG.......................................................................................................................... 32
I. ALLGEMEINE HINWEISE.............................................................................................................................................................................32
1. ENTSORGUNG DER VERPACKUNG UND DES GERÄTS ................................................................................................................................................... 33
2. SICHERHEITS VORRICHTUNGEN.................................................................................................................................................................................... 33
II. INSTALLATIONSANLEITUNGEN..................................................................................................................................................................33
3. HINWEISE FÜR DEN INSTALLATIONSTECHNIKER........................................................................................................................................................... 33
4. BEZUGSNORMEN UND -GESETZE ................................................................................................................................................................................. 34
5. AUSPACKEN..................................................................................................................................................................................................................34
6. GERÄTEAUFSTELLUNG.................................................................................................................................................................................................. 34
7. ANSCHLÜSSE.................................................................................................................................................................................................................34
8. UMSTELLUNG AUF EINE ANDERE GASART.................................................................................................................................................................... 51
9. INBETRIEBNAHME ........................................................................................................................................................................................................ 37
modular gassolidtop700-900 G23M 2/80

III. BEDIENUNGSANWEISUNGEN....................................................................................................................................................................37
10. HINWEISE FÜR DEN BENUTZER .................................................................................................................................................................................... 37
11. GEBRAUCH DERGASKOCHMULDE................................................................................................................................................................................. 38
12. GEBRAUCH DES GLUHPLA TTENHERDES/WÀRME-PLATTEN......................................................................................................................................... 38
13. GEBRAUCH DES GASOFENS .......................................................................................................................................................................................... 39
14. GEBRAUCH DES ELEKTROKOCHFELDS........................................................................................................................................................................... 40
15. VERWENDUNG DES HEIΒLUFT OFEN ............................................................................................................................................................................ 40
16. VERWENDUNG DES STATISCHES ELEKTRO OFEN.......................................................................................................................................................... 41
17. STILLSTANDZEITEN .......................................................................................................................................................................................................41
IV. REINIGUNGSANLEITUNGEN ......................................................................................................................................................................42
18. REINIGUNGSHINWEISE................................................................................................................................................................................................. 42
V. WARTUNGSANLEITUNGEN........................................................................................................................................................................42
19. HINWEISE FÜR DEN WARTUNGSTECHNIKER ................................................................................................................................................................ 42
20. UMSTELLUNG AUF EINE ANDERE GASART.................................................................................................................................................................... 42
21. INBETRIEBNAHME ........................................................................................................................................................................................................ 42
22. ABHILFE BEI BETRIEBSSTÖRUNGEN.............................................................................................................................................................................. 42
23. ERSATZ VON BAUTEILEN............................................................................................................................................................................................... 44
24. REINIGUNG DER INNEREN GERÀTETEILE ...................................................................................................................................................................... 45
25. HAUPTKOMPONENTEN ................................................................................................................................................................................................ 45
NL - INSTALLATIE - GEBRUIK - ONDERHOUD ............................................................................................................................. 47
I. ALGEMENE MEDEDELINGEN .....................................................................................................................................................................47
1. VERWIJDERING VERPAKKING EN APPARATUUR ........................................................................................................................................................... 48
2. VEILIGHEIDSINRICHTINGEN.......................................................................................................................................................................................... 48
II. AANWIJZINGEN VOOR DE INSTALLATIE.....................................................................................................................................................48
3. MEDEDELINGEN VOOR DE INSTALLATEUR ................................................................................................................................................................... 48
4. REFERENTIENORMEN EN -WETTEN .............................................................................................................................................................................. 49
5. UITPAKKEN................................................................................................................................................................................................................... 49
6. PLAATSING ................................................................................................................................................................................................................... 49
7. AANSLUITINGEN........................................................................................................................................................................................................... 49
8. AANPASSING OP EEN ANDER GASTYPE ........................................................................................................................................................................ 50
9. INBEDRIJFSTELLING ...................................................................................................................................................................................................... 52
III. GEBRUIKSAANWIJZINGEN.........................................................................................................................................................................52
10. MEDEDELINGEN VOOR DE GEBRUIKER......................................................................................................................................................................... 52
11. GEBRUIK VAN DE KOOKPLAAT GAS .............................................................................................................................................................................. 3
12. GEBRUIK VAN DE GRILLPLATEN/SIMPLE SERVICE......................................................................................................................................................... 53
13. GEBRUIK VAN DE OVEN GAS ........................................................................................................................................................................................ 54
14. GEBRUIK VAN DE KOOKPLAAT ELEKTRISCH.................................................................................................................................................................. 55
15. GEBRUIK VAN DE OVEN ELEKTRISCH CONVECTIE ......................................................................................................................................................... 55
16. GEBRUIK VAN DE OVEN ELEKTRISCH STATISCH (SERIE 900) ......................................................................................................................................... 56
17. INUTILITEITSPERIODE ................................................................................................................................................................................................... 56
IV. AANWIJZINGEN VOOR DE REINIGING........................................................................................................................................................57
18. MEDEDELINGEN VOOR DE REINIGING.......................................................................................................................................................................... 57
V. ONDERHOUDSAANWIJZINGEN..................................................................................................................................................................57
19. MEDEDELINGEN VOOR HET ONDERHOUDSPERSONEEL ............................................................................................................................................... 57
20. AANPASSING OP EEN ANDER GASTYPE ........................................................................................................................................................................ 57
21. INBEDRIJFSTELLING ...................................................................................................................................................................................................... 57
22. STORINGEN OPLOSSEN................................................................................................................................................................................................. 57
23. VERVANGING VAN DE COMPONENTEN........................................................................................................................................................................ 59
24. REINIGING VAN DE INTERNE ONDERDELEN.................................................................................................................................................................. 60
25. HOOFDCOMPONENTEN................................................................................................................................................................................................ 60
VI. INSTALLATIONS PLAN -INSTALLATION DIAGRAM –SCHEMA D’INSTALLATION – INSTALLATIESCHEMA'S ................................................ 62
VII. ABB. –FIG. FIGURE-FIG.-IMAGE-ABB.-AFBEELDINGEN..........................................................................................................................73
VIII. TAB1 -TECHNICAL DATA -TECHNISCHE DATEN -CARACTERISTIQUES TECHNIQUES -DATOS TECNICOS -TECHNISCHE GEGEVENS
NOZZLES AND SETTINGS -BUSES ET LES PARAMÈTRES -DUSEN UND EINSTELLUNGEN -VERSTUIVERS EN REGELINGEN .............................................................................................77
TAB2 -TECHNICAL DATA -TECHNISCHE DATEN -CARACTERISTIQUES TECHNIQUES -TECHNISCHE GEGEVENS CATEGORIES AND PRESSURES -
CATÉGORIES ET PRESSIONS -KATEGORIEN E DRUCK -CATEGORIEËN EN DRUK............................................................................................................................................................... 75
IX. TAB3 -TECHNICAL DATA -TECHNISCHE DATEN -CARACTERISTIQUES TECHNIQUES -TECHNISCHE GEGEVENS -TECHNICAL DATA OF GAS
APPLIANCES -CARACTÉRISTIQUES TECHNIQUES DES APPAREILS À GAZ -TECHNISCHE DATEN GASGERATE - TECHNISCHE GEGEVENS GASAPPARATUUR ............................................78
X. TAB4 -TECHNICAL DATA -TECHNISCHE DATEN -CARACTERISTIQUES TECHNIQUES -TECHNISCHE GEGEVENS DATA OF ELECTRIC APPLIANCES -
CARACTÈRISTIQUES TECHNIQUES DES APPAREILS ELECTRIQUES - TECHNISCHE DATEN ELEKTROGERATE - TECHNISCHE GEGEVENS ELEKTRISCHE APPARATUUR ..................................80
modular gassolidtop700-900 G23M 3/80

UK - INSTALLATION –USE - MAINTENANCE
I. GENERAL PRESCRIPTIONS
READ THIS MANUAL CAREFULLY. IT
PROVIDES IMPORTANT INFORMATION
FOR SAFE INSTALLATION, USE AND
MAINTENANCE OF THE APPLIANCE.
FAILURE TO COMPLY WITH WHAT IS
PRESENTED BELOW MAY COMPROMISE
THE SAFETY OF THE EQUIPMENT.
THE MANUFACTURER WILL NOT BE
LIABLE FOR ANY DAMAGE OR INJURY
RESULTING FROM FAILURE TO
OBSERVING THE FOLLOWING RULES.
TRANSLATION OF THE ORIGINAL
INSTRUCTIONS.
APPLIANCES NEED PRECAUTIONS FOR
INSTALLATION, PLACING A
ND/OR
FIXATION AND CONNECTION TO THE
MAINS.
SEE SECTION “INSTALLATION
INSTRUCTIONS”.
THE APPLIANCES NEED PRECAUTIONS
FOR CLEANING. SEE THE SECTION “
INSTRUCTION FOR CLEANING”.
THE SYMBOL “ HIGH VOLTAGE” IS
PLACED ON A PANEL THAT GIVES ACCESS
TO A PART WITH HIGH VOLTAGE.
Keep this manual in a safe place, known to all users,
so that it can be consulted throughout the working
life of the appliance.
This equipment is designed for cooking food. It is
intended for industrial use. Any other use is to be
considered improper
This appliance is not intended for use by people
(including children) with limited physical, sensory or
mental abilities or without experience and
knowledge of it.
Unless they are supervised or instructed in its use
by a person responsible for their safety.
Do not leave de appliance unattended in presence
of children and ensure that the latter do not have
acces to the appliance.
The appliance must be used by trained personnel.
Do not leave the appliance unattended when
operating.
DO NOT STORE " AMMABLE MATERIALS
IN CLOSE PROXIMITY TO THE APPLIANCE.
FIRE HAZARD.
The appliance must be installed in a well-ventilated
room.
Inadequate ventilation causes asphyxia. Do not
obstruct the ventilation system of the place where
the
appliance is installed. Do not obstruct the vents or
ducts of this or other appliances.
In the event of an appliance fault or malfunction,
shut the gas shut-off valve and/or switch the
appliance off at the main switch installed upline.
Installation and conversion to a different type of gas
must be carried out by qualified technicians
authorized by the manufacturer, in compliance with
current safety standards and the instructions in this
manual.
Appliance maintenance and conversion to a
different type of gas must be carried out by
qualified technicians authorized by the
manufacturer, in compliance with current safety
standards and the instructions in this manual.
Clean the appliance following the instructions given
in Chapter “ INSTRUCTIONS FOR CLEANING”.
1. DISPOSAL OF PACKING AND OF THE
APPLIANCE
PACKING
modular gassolidtop700-900 G23M 4/80

The packing is made using environmentally friendly
materials. The plastic recyclable components are:
-
the transparent cover, the bags containing the
instructions manual and nozzles (made of
Polyethylene - PE).
-
the straps (in Polypropylene - PP).
APPLIANCE
The appliance is manufactured 90% from recyclable
metals (stainless steel, aluminium sheet, copper.. ..
).
The appliance must be scrapped in compliance with
current regulations governing such disposal.
Make the appliance unusable before scrapping.
It must be disposed of properly.
THE SYMBOL SHOWING A CROSSED-OUT
WASTE C
ONTAINER ON THE UNIT OR
PACKAGE INDICATES THAT, AT THE E
ND
OF ITS LIFE CYCLE, THE PRODUCT MUST
BE COLLECTED SEPARATE FROM OTHER
WASTE.
THE DIFFERENTIATED COLLECTION OF THIS
EQUIPMENT IS ORGANISED AND MANAGED BY THE
PRODUCER.
THE USER WHO INTENDS TO GET RID OF THIS
EQUIPMENT SHALL CONTACT THE PRODUCER AND
FO
LLOW THE SYSTEM THAT THE LATTER HAS USED
IN ORDER TO COLLECT THE EQUIPMENT
SEPARATELY AT THE END OF ITS LIFE.
PROPER SEPARATE COLLECTION HELPS PREVENT
POSSIBLE NEGATIVE IMPACTS ON THE
ENVIRONMENT A
ND HEALTH, AND FAVOURS THE
REUSE AND/OR RECYCLING OF THE
UNIT’S
MATERIALS.
ABUSIVE DISPOSAL OF THE PRODUCT BY THE
HOLDER WILL RESULT IN THE APPLICATION OF
PENALTIES AS PER CURRENT STANDARDS.
2. SAFETY DEVICES
ELECTRIC OVEN
SAFETY THERMOSTAT
THE MANUFACTURER WILL NOT BE
LIABLE FOR ANY DAMAGE
OR INJURY
RESULTING FROM FAILURE TO
OBSERVING THE FOLLOWING RULES.
The appliance is equipped with a manual reset
safety thermostat that interrupts heating when the
operating temperature exceeds the maximum
permitted value.
To restore appliance operation, remove the control
panel and press the thermostat reset button. This
procedure must only be carried out by a qualified,
authorized technician.
II. INSTRUCTIONS FOR
INSTALLATION
3. REMINDERS FOR THE INSTALLER
READ THIS MANUAL CAREFULLY. IT
PROV
IDES IMPORTANT INFORMATION
FOR SAFE INSTALLATION, USE AND
MAINTENANCE OF THE APPLIANCE.
FAILURE TO COMPLY WITH WHAT IS
PRESENTED BELOW MAY COMPROMISE
THE SAFETY OF THE EQUIPMENT.
THE MANUFACTURER WILL NOT BE
LIABLE FOR ANY DAMAGE OR INJURY
RESULT
ING FROM FAILURE TO
OBSERVING THE FOLLOWING RULES.
Identify the specific appliance model. The model
number is detailed on the packing and on the
appliance dataplate.
The appliance must be installed in a well-ventilated
room.
Installation and conversion to a different type of gas
must be carried out by qualified technicians
authorized by the manufacturer, in compliance with
current safety standards and the instructions in this
manual.
Appliance maintenance and conversion to a
different type of gas must be carried out by
qualified technicians authorized by the
manufacturer, in compliance with current safety
standards and the instructions in this manual.
Do not obstruct any air vents or drains present on
the appliance.
Do not tamper with appliance components.
4. REFERENCE STANDARDS AND LAWS
Install the appliance in accordance with the safety
standards in force in the country.
5. UNPACKING
modular gassolidtop700-900 G23M 5/80

Check the state of the packing and in the event of
damage, ask the delivery person to inspect the
goods.
Remove the packing.
Remove the protective film from the outer panels.
Use a suitable solvent to remove any residual
adhesive from the panels.
6. POSITIONING
The overall dimensions of the appliance and the
position of connections are given on the installation
diagram at the end of this manual.
The appliance can be installed singly or in
combination with other appliances in the same
product range.
The appliance is not suitable for integrated
installation.
Position the appliance at least 10 cm from adjacent
walls.
If the appliance is to be be placed near walls,
dividers, kitchen furniture, decorative elements etc.
this must be made of non-combustible materials
Otherwise, they must be covered with suitable
non-combustible heat insulating materials.
Level the appliance by means of the height-
adjustable feet
APPLIANCE ASSEMBLY WITH BASE AND BRIDGE
Follow the instructions provided with the type of
support utilized.
FUMES EXHAUST SYSTEM
Create a fumes exhaust system based on the " Type
" of appliance. The " Type " is stated on the
appliance dataplate.
" A1 " TYPE APPLIANCE
Position the “A1” type appliance below an extractor
hood to ensure smoke and fumes generated by
cooking are removed.
" B21 " TYPE APPLIANCE
Position the “B21” type appliance below an
extractor hood.
" B11 " TYPE APPLIANCE
Fit the “B11” type appliance with a suitable fl ue,
available from the appliance manufacturer. Follow
the assembly instructions provided with the flue.
Connect the flue to a 150/155 mm diameter hose,
heat resistant to 300°C.
Vent to the outside or into an effi cient fl ue. The
hose length must not exceed 3 metres.
7. CONNECTIONS
The position and dimensions of connections are
given in the installation diagram at the end of this
manual.
CONNECTION TO THE GAS SUPPLY
Check that the appliance is designed to operate
with the type of gas supply present on site. Check
the information given on the decals on the packing
and appliance.
Convert the appliance to the local gas type, if
necessary. Follow the instructions at the next
paragraph “Conversion to a different type of gas”.
On top appliances a rear connection is also
available. Remove the plug present and screw it
tightly onto the front connector.
A rapid-action gas shut-off valve must be fitted
upstream of the appliance in an easily accessible
position.
Do not use connection pipes having a diameter
smaller than that of the appliance's gas connector.
Once the appliance has been installed, check for gas
leaks at the connection points.
ELECTRICAL CONNECTIONS
Check if the appliance is designed to operate at the
voltage and frequency of the power supply present
on site. Check the details given on the appliance
dataplate and plaque near the terminal board.
Install upstream of the equipment in an easily
accessible place, an all-pole disconnecting device
with a contact gap of allowing full disconnection
under the conditions of overvoltage category III.
A flexible rubber cable with insulation specifications
not lower than type H05 RN-F must be used for
connection.
Connect the power supply cable to the terminal
board as shown in the wiring diagram supplied with
the appliance.
modular gassolidtop700-900 G23M 6/80

Secure the power supply cable with the cable
clamp.
Protect the power supply cable on the outside of
the appliance with a rigid plastic or metal pipe.
If the power supply cable is damaged, it must be
replaced by the manufacturer or his service centre
or by a person with similar qualifications to prevent
any risk.
THE SYMBOL “ HIGH VOLTAGE” IS
PLACED ON A PANEL THAT GIVES ACCESS
TO A PART WITH HIGH VOLTAGE.
PROTECTIVE EARTH AND EARTH BONDING
CONNECTIONS
Connect the appliance to an efficient ground circuit.
Connect the earth conductor to the terminal with
the symbol next to the main terminal board.
Connect the metal structure of the appliance to the
equipotential node. Connect the conductor to the
terminal with the symbol on the outside part of
the bottom.
CONNECTION TO THE WATER SUPPLY
The appliance must be connected to a potable
water supply. The water inlet pressure must be
between 150 kPa and 300 kPa. Use a pressure
reducer if the inlet pressure is above the maximum
permitted level.
Install a mechanical filter and a shut-off valve
upstream of the appliance in an easily accessible
point.
Make sure the water circuit is free of ferrous
particles before connecting the filter and the
appliance.
Seal any unused connectors with a plug.
Once the appliance has been installed, check for gas
leaks at the connection points.
CONNECTION TO THE WATER DRAIN
The water drainage system must be made using
materials resistant to temperatures of 100 °C. The
bottom of the appliance must not be subjected to
steam produced by drainage of hot water.
Install a siphoned floor drain with grating below the
water drain cock of Boiling pans and in front of
Bratt pans.
8. CONVERSION TO ANOTHER
TYPE OF GAS
Table Tab1 specifies:
-
which gas can be used for the appliance.
-
the nozzles and settings for each gas that can be
used.
For nozzles, the number indicated in table TAB1 is
also stamped on the body of nozzles.
To convert the appliance to the local gas type,
follow the instructions given in TAB1 andcarry out
the steps below:
-
Replace the main burner nozzle (UM).
-
Adjust the main burner's air regulator to distance A.
-
Replace the pilot burner nozzle (UP).
-
Adjust the pilot burner air " ow (if necessary).
-
Replace the gas valve minimum nozzle (Um).
-
Affix the adhesive tab indicating the new type of gas
used.
-
The nozzles and adhesive tabs are supplied with the
appliance.
GAS HOB
REPLACING THE MAIN BURNER NOZZ
LE
Remove the control panel.
Remove pan stand grids, basins and burners.
Remove nozzle UM and replace it with the one
indicated in table TAB1.
Retighten nozzle UM.
Reassemble all parts. For assembly, proceed in
reverse order.
REPLACING
THE MINIMUM ADJUSTMENT SCREW
Remove the control panel.
Remove nozzle UM and replace it with the one
indicated in table TAB1.
Retighten nozzle UM.
Reassemble all parts. For assembly, proceed in
reverse order.
REPLACING THE PILOT BURNER NOZZ
LE
Remove the control panel.
Remove pan stand grids, basins and burners.
Undo connector R.
Remove nozzle UP and replace it with the one
indicated in table TAB1.
Retighten connector R. Reassemble all parts.
modular gassolidtop700-900 G23M 7/80

Following, in reverse order, the sequence used for
their removal.
GAS SOLID TOP RANGES
REPLACING THE NOZZLE AND THE MAIN BURNER
PRIMARY AIR REGULATION
Remove the control panel.
Remove nozzle UM and replace it with the one
indicated in table TAB1.
Retighten nozzle UM.
Slacken screw V and position the air regulator at
distance A as indicated in table TAB1.
Retighten screw V fully.
Reassemble all parts. For assembly, proceed in
reverse order.
REPLACING T
HE MINIMUM ADJUSTMENT SCREW
Remove the control panel.
Remove nozzle UM and replace it with the one
indicated in table TAB1.
Retighten nozzle UM.
Reassemble all parts. For assembly, proceed in
reverse order.
REPLACING THE PILOT BURNER NOZZL
E
Remove the control panel and internal guards.
Undo connector R.
Remove nozzle UP and replace it with the one
indicated in table TAB1.
Retighten connector R. Reassemble all parts.
Following, in reverse order, the sequence used for
their removal.
GAS OVEN
REPLACING THE NOZZLE AND THE MAIN BURNER
PRIMARY AIR REGULATION
Open the oven door.
remove the sole and the protection panel
Slacken screw V.
remove the UM nozzle.
Retighten nozzle UM.
Place the aeration adjuster at the distance A
specified in the table TAB1.
Retighten screw V fully.
Reassemble all parts. For assembly, proceed in
reverse order.
PILOT BURNER NOZZLE REPLACEMENT (ONLY 900
SERIES)
Open the oven door.
remove the sole and the protection panel
Undo connector R.
Remove nozzle UP and replace it with the one
indicated in table TAB1.
Retightenconnector R.
Reassemble all parts. For assembly, proceed in
reverse order.
9. COMMISSIONING
Following installation, conversion to a different type
of gas or any maintenance operations, check
appliance operation. In the event of any
malfunction, consult the next Paragraph "
Troubleshooting " .
GAS APPLIANCES
Switch on the appliance as directed in the
instructions and reminders for use given in Chapter
“ INSTRUCTIONS FOR USE “ and check:
-
the gas supply pressure (see next Paragraph).
-
the correct ignition of the burners and the
effectiveness of the fumes removal system.
CHECKING THE GAS SUPPLY PRESSURE
To measure the gas supply pressure use a
manometer with a minimum definition of 0,1 mbar.
Remove the control panel.
Remove the screw from on pressure test point PP
and connect the manometer to the test point.
Make the measurement with the appliance in
operation.
IMPORTANT! IF THE GAS SUPPLY
PRESSURE IS NOT WITHIN
THE LIMITS
(MIN.
- MAX) INDICATED IN TABLE TAB2,
CEASE OPERATION OF THE APPLIANCE
AND CONTACT THE GAS UTILITY
COMPANY.
Disconnect the manometer and retighten the
retaining screw on the pressure connection.
modular gassolidtop700-900 G23M 8/80

ELECTRIC EQUIPMENT
Switch on the appliance as directed in the
instructions and reminders for use given in Chapter
“ INSTRUCTIONS FOR USE “ and check:
-
the current values of each phase.
-
the correct operation of the heating elements.
III. INSTRUCTIONS FOR USE
10.REMINDERS FOR THE USER
READ THIS MANUAL CAREFULLY. IT
PROVIDES IMPORTANT INFORMATION
FOR SAFE INSTALLATION, USE AND
MAINTENANCE OF THE APPLIANCE.
THE MANUFACTURER WILL NOT BE
LIABLE FOR ANY DAMAGE OR INJURY
RESU
LTING FROM FAILURE TO
OBSERVING THE FOLLOWING RULES.
For after-sales service, contact technical assistance
centres authorized by the manufacturer and
demand the use of original spare parts.
Have the appliance serviced at least twice a year.
The manufacturer recommends taking out a service
contract.
The appliance is designed for professional use and
must be operated by trained personnel.
The appliance is to be used for cooking food as
specified in the prescriptions for use. Any other use
is considered to be improper.
Do not allow the appliance to operate empty for
prolonged periods. Only pre-heat the oven just
before use.
Do not leave the appliance unattended while in
operation.
In the event of an appliance fault or malfunction,
shut the gas shut-off valve and/or switch the
appliance off at the main switch installed upline.
Clean the appliance following the instructions given
in Chapter “ INSTRUCTIONS FOR CLEANING”.
DO NOT STORE " AMMABLE MATERIALS
IN CLOSE PROXIMITY TO THE APPLIAN
CE.
FIRE HAZARD.
Do not obstruct any air vents or drains present on
the appliance.
Do not tamper with appliance components.
Keep this manual in a safe place, known to all users,
so that it can be consulted throughout the working
life of the appliance.
Installation and appliance maintenance must be
carried out by qualified technicians authorized by
the manufacturer, in compliance with current safety
standards and the instructions in this manual.
Appliance maintenance and conversion to a
different type of gas must be carried out by
qualified technicians authorized by the
manufacturer, in compliance with current safety
standards and the instructions in this manual.
11.USING THE GAS HOB
The appliance is designed for cooking foods
contained in pots and pans.
The pilot burners have to be turned on manually.
Check that the flame spreaders are correctly placed
on the burners.
BURNER IGNITION AND EXTINCTION
The gas tap control knob has the following
positions:
OFF
PIL
OT IGNITION
MAX. FLAME
MIN. FLAME
PILOT IGNIT
ION
Press and turn knob to “pilot on”.
Press the knob down fully and light the pilot with a
flame.
Hold the knob down for about 20 seconds before
releasing it. If the pilot flame goes out, repeat the
operation.
MAIN BURNER IGNITION
To light the main burner, turn the knob from “pilot
on” to “max. flame”.
For the minimum flame, turn the knob from “max.
flame” to “min. flame”.
modular gassolidtop700-900 G23M 9/80

TURNING OFF
Turn the knob from “max. flame” or “min. flame”
to “pilot on”.
To shut off the pilot, press the knob lightly and turn
it to “off”.
12.USING THE HOTPLATE/SIMPLE SERVICE
The appliance is designed for cooking foods
contained in pots and pans.
The highest temperatures are in the centre of the
hotplate.
Check that the flame spreader is correctly placed on
the burner. Raise the central disc on the hotplate.
BURNER IGNITION AND EXTINCTION
The gas tap control knob has the following
positions:
OFF
PILOT IGNITION
MAX. FLAME
MIN. FLAME
PILOT IGNITION
Press and turn knob to “pilot on”.
Press the knob down fully and light the pilot using
the piezoelectric igniter.
Hold the knob down for about 20 seconds before
releasing it. If the pilot flame goes out, repeat the
operation.
The pilot flame can be seen through the peep hole
on the control panel.
The pilot light can be lit by bringing an open flame
up to the nozzle. Raise the central disc on the
hotplate.
MAIN BURNER IGNITION
To light the main burner, turn the knob from “pilot
on” to “max. flame”.
For the minimum flame, turn the knob from “max.
flame” to “min. flame”.
TURNING OFF
Turn the knob from “max. flame” or “min. flame”
to “pilot on”.
To shut off the pilot, press the knob lightly and turn
it to “off”.
13.USING THE GAS OVEN
The appliance is designed for cooking foods placed
on the grilles provided.
Do not leave the door even partially open during
use.
BURNER IGNITION AND EXTINCTION (700)
the control knob of the thermostatic tap has the
following positions use:
OFF
MINIMUM TEMPERATURE
INTERMEDIATE TEMPERATURES
MAXIMUM WATER TEMPERATURE
MAIN BURNER IGNITION
Turn the knob to the chosen temperature setting
for cooking.
modular gassolidtop700-900 G23M 10/80

Press the knob down simultaneously with the
piezoelectric unit . Press the knob down for 10-15
seconds and then leave it; the pilot burner will
remain on.
If it turns off, repeat the operation.
TURNING OFF
to switch off the main burner turn the knob to the
"off" position.
BURNER IGNITION AND EXTINC
TION (900)
the control knob of the thermostatic tap has the
following positions use:
OFF
PILOT IGNITION
MAXIMUM WATER TEMPERATURE
INTERMEDIATE TEMPERATURES
MINIMUM TEMPERATUR
E
PILOT IGNITION
Press and turn knob to “pilot on”.
Press the knob down simultaneously with the
piezoelectric unit . Press the knob down for 15-20
seconds and then leave it; the pilot burner will
remain on.
if the pilot burner turns off, repeat the operation.
The pilot flame can be seen through the peep hole
on the floor of the oven. First of all lift the peep
hole cover.
The pilot flame can be lit with a flame.
MAIN BURNER IGNITION
Turn the knob to the chosen temperature setting
for cooking.
TURNING OFF
To switch the main burner off, turn the knob to
position " pilot on " .
To shut off the pilot, press the knob lightly and turn
it to “off”.
14.USING THE ELECTRIC HOB
The appliance is designed for cooking foods
contained in pots and pans.
Use flat bottomed pans.
Do not leave the hotplates switched on with no pan
or an empty pan in place.
Do not pour cold liquids onto the hot hotplate.
SWITCHING ON AND OFF
The control knob has the following positions:
OFF
MINIMUM TEMPERATURE
INTERMEDIA
TE TEMPERATURES
MAXIMUM WATER TEMPERATURE
SWITCHING ON
Turn the control knob to the chosen position.
The green indicator light switches on.
TURNING OFF
Turn the knob to position " 0 " .
the green indicator lamp turn off only when all the
plates are off
15.ELECTRIC CONVECTION OVEN USE
modular gassolidtop700-900 G23M 11/80

The appliance is designed for cooking foods placed
on the grilles provided.
Do not leave the door even partially open during
use.
The appliance is equipped with a manual reset
safety thermostat that interrupts heating when the
operating temperature exceeds the maximum
permitted value.
SWITCHING ON AND OFF
The thermostat control knob has the following
positions:
OFF
MI
NIMUM TEMPERATURE
INTERMEDIATE TEMPERATURES
MAXIMU
M WATER TEMPERATURE
SWITCHING ON
Turn the control knob to the chosen position.
Turn the thermostat knob to the chosen
temperature setting for cooking.
the yellow and the green indicator lamp turn on.
The yellow indicator light switches off when the
oven reaches the set temperature.
TURNING OFF
Turn the thermostat knob to position " 0 " .
the yellow and the green indicator lamp turn off.
16.ELECTRIC STATIC OVEN USE (900
SERIES)
The appliance is designed for cooking foods placed
on the grilles provided.
Do not leave the door even partially open during
use.
The appliance is equipped with a manual reset
safety thermostat that interrupts heating when the
operating temperature exceeds the maximum
permitted value.
SWITCH
ING ON AND OFF
The electric oven is controlled by two knobs (for
selecting the type of heating and the cooking
temperature). A yellow indicator light indicates
operation of the heating elements.
The control knob has the following positions:
O
FF
UPPER HEATING ELEMENT
LOWER HEATING ELEMENT
UPPER AND LOWER HEATING ELEMENTS
The thermostat control knob has the following
positions:
OFF
MINIMUM TEMPERATURE
INTERMEDIATE TEMPERATURES
MAXIMUM WATER TEMPERATURE
SWITCH
ING ON
Turn the control knob to the chosen position.
modular gassolidtop700-900 G23M 12/80

Turn the thermostat knob to the chosen
temperature setting for cooking.
The green indicator light switches on.
The yellow indicator light switches off when the
oven reaches the set temperature.
TURNING OFF
Turn the thermostat knob to position " 0 " .
Turn the knob to position " 0 " .
17.PROLONGED DISUSE
Before any prolonged disuse of the appliance,
proceed as follows:
-
Clean the appliance thoroughly.
-
Rub stainless steel surfaces with a cloth soaked in
vaseline oil to create a protective film.
-
Leave pot lids open.
-
Close cocks or main switches ahead of the
appliances.
Following prolonged disuse, proceed as follows:
-
Inspect the appliance thoroughly before using it
again.
-
Allow electric appliances to operate at the lowest
temperature for at least 60 minutes.
IV. INSTRUCTIONS FOR
CLEANING
18.REMINDERS FOR CLEANING
READ THIS MANUAL CAREFULLY. IT
PROVIDES IMPORTANT INFORMATION
FOR SAFE INSTALLA
TION, USE AND
MAINTENANCE OF THE APPLIANCE.
THE MANUFACTURER WILL NOT BE
LIABLE FOR ANY DAMAGE OR INJURY
RESULTING FROM FAILURE TO
OBSERVING THE FOLLOWING RULES.
DISCONNECT THE APPLIANCE ELECTRIC
SUPPLY, IF PRESENT, BEFORE CARRYING
OUT ANY OPERATION.
Clean the satin finish stainless steel exterior
surfaces, the cooking wells and the surface of the
hotplates every day.
At least twice a year, have an authorized technician
clean the internal parts of the appliance.
Do not use corrosive products to clean the floor
beneath the appliance.
Do not use direct or high pressure water jets to
clean the appliance.
SATIN FINISH STAINLESS STEEL SURFACES
Clean the surfaces with a cloth or sponge using
water and proprietary non-abrasive detergents.
Follow the direction of the satin finish lines. Rinse
repeatedly and dry thoroughly.
Do not use pan scourers or other iron items.
Do not use chemical products containing chlorine.
Do not use sharp objects which might scratch and
damage the surfaces.
ELECTRIC HOTPLATES
Clean surfaces with a damp cloth.
Switch on for a few minutes to dry rapidly.
Lubricate surfaces with a fine coat of food grade oil.
HOTPLATE RANGE
Clean surfaces with a damp cloth.
Switch on for a few minutes to dry rapidly.
Lubricate surfaces with a fine coat of food grade oil.
V. INSTRUCTIONS FOR
MAINTENANCE
19.REMINDERS FOR THE MAINTENANCE
TECHNICIAN
THE MANUFACTURER WILL NOT BE
LIAB
LE FOR ANY DAMAGE OR INJURY
RESULTING FROM FAILURE TO
OBSERVING THE FOLLOWING RULES.
Identify the specific appliance model. The model
number is detailed on the packing and on the
appliance dataplate.
The appliance must be installed in a well-ventilated
room.
Do not obstruct any air vents or drains present on
the appliance.
Do not tamper with appliance components.
modular gassolidtop700-900 G23M 13/80

Appliance maintenance and conversion to a
different type of gas must be carried out by
qualified technicians authorized by the
manufacturer, in compliance with current safety
standards and the instructions in this manual.
20.CONVERSION TO ANOTHER TYPE OF
GAS
See Chapter “ Instructions for installation “.
21.COMMISSIONING
See Chapter “ Instructions for installation “.
22.TROUBLESHOOTING
GAS HOB
THE PILOT BURNER
DOES NOT LIGHT.
Possible causes:
-
Insufficient gas supply pressure.
-
Blocked tubing or nozzle.
-
Defective gas tap or valve.
PILOT BURNER GOES OUT DURING USE.
Possible causes:
-
Insufficient gas supply pressure.
-
Defective gas tap or valve.
-
Defective thermocouple or insufficient heating.
-
Thermocouple incorrectly connected to gas tap or
valve.
-
Knob of gas tap or valve not pressedsufficiently.
THE MAIN BURNER DOES NOT LIGHT (EVEN
THOUGH PILOT IS LIT).
Possible causes:
-
Insufficient gas supply pressure.
-
Blocked tubing or nozzle.
-
Defective gas tap or valve.
-
Defective burner (gas outlet holes clogged).
GAS SOLID TOP RANGES
THE PILOT BURN
ER DOES NOT LIGHT.
Possible causes:
-
Insufficient gas supply pressure.
-
Blocked tubing or nozzle.
-
Defective gas tap or valve.
-
Igniter defective or not properly connected.
-
Igniter or igniter wire defective.
PILOT BURNER GOES OUT D
URING USE.
Possible causes:
-
Insufficient gas supply pressure.
-
Defective gas tap or valve.
-
Defective thermocouple or insufficient heating.
-
Thermocouple incorrectly connected to gas tap or
valve.
-
Knob of gas tap or valve not pressedsufficiently.
THE MAIN BURNER DOES NOT LIGHT (EVEN
TH
OUGH PILOT IS LIT).
Possible causes:
-
Insufficient gas supply pressure.
-
Blocked tubing or nozzle.
-
Defective gas tap or valve.
-
Defective burner (gas outlet holes clogged).
GAS O
VEN
THE PILOT BURNER DOESN'T TURN ON (900 SERIES)
Possible causes:
-
Insufficient gas supply pressure.
-
Blocked tubing or nozzle.
-
Defective gas tap or valve.
-
Igniter defective or not properly connected.
-
Igniter or igniter wire defective.
THE PILOT BURNER DOESN'T STAY ON OR TURNS
OF
F DURING THE USE. (900 SERIES)
Possible causes:
-
Insufficient gas supply pressure.
-
Defective gas tap or valve.
-
Defective thermocouple or insufficient heating.
-
Thermocouple incorrectly connected to gas tap or
valve.
modular gassolidtop700-900 G23M 14/80

-
Knob of gas tap or valve not pressedsufficiently.
THE MAIN BURNER DOES NOT LIGHT (EVEN
THOUGH PILOT IS LIT).
Possible causes:
-
Insufficient gas supply pressure.
-
Blocked tubing or nozzle.
-
Defective gas tap or valve.
-
Defective burner (gas outlet holes clogged).
HEATING CANNOT BE ADJUSTED.
Possible causes:
-
Defective gas tap or valve.
ELECTRIC HOB
THE HOTPLATE DOES NOT HEAT.
Possible causes:
-
Hotplate defective.
ELEC
TRIC OVEN
THE APPLIANCE DOES NOT HEAT.
Possible causes:
-
Temperature thermostat defective.
-
Heating elements defective.
-
Safety thermostat tripped.
HEATING CANNOT BE ADJUSTED.
Possible causes:
-
Temperature thermostat defective.
23.REPLACING COMPONENTS
REMINDERS FOR REPLAC
ING COMPONENTS
SHUT THE GAS SHUT
-OFF VALVE AND/OR
SWITCH THE APPLIANCE OFF AT THE
MAIN SWITCH INSTALLED UPSTREAM.
AFTER REPLACING A GAS SYSTEM
COMPONENT, CHECK FOR GAS LEAKS AT
CONNECTION POINTS.
DISCONNECT THE APPLIANCE ELECTRIC
SUPPLY,
IF PRESENT, BEFORE CARRYING
OUT ANY OPERATION.
AFTER REPLACING AN ELECTRICAL
SYSTEM COMPONENT, CHECK IT IS
CORRECTLY WIRED.
GAS HOB
REPLACING THE GAS TAP.
-
Remove the control panel.
-
Remove and replace the component.
-
Reassemble all parts. For assembly, proceed in
reverse order.
REPLACING THE PILOT BURNER AND
THERMOCOUPLE.
-
Remove the control panel.
-
Remove pan stand grids, basins and burners.
-
Remove and replace the component.
-
Reassemble all parts. For assembly, proceed in
reverse order.
GAS SOLID TOP RANGES
REPLACING THE GAS TAP AND PIEZO IGNITER.
-
Remove the control panel.
-
Remove and replace the component.
-
Reassemble all parts. For assembly, proceed in
reverse order.
REPLACING THE MAIN
BURNER, PILOT BURNER,
THERMOCOUPLE AND IGNITER.
-
Remove the hotplate.
-
Remove the control panel and internal guards.
-
Remove and replace the component.
-
Reassemble all parts. For assembly, proceed in
reverse order.
GAS OVEN
THERMOSTATIC TAP AND PIEZOELECTRIC UNIT
REPLACEMENT
modular gassolidtop700-900 G23M 15/80

-
Remove the control panel.
-
Remove the bulb from its seat on the side of the
oven.
-
Remove and replace the component.
-
Reassemble all parts. For assembly, proceed in
reverse order.
REPLACING THE
BURNER
-
Open the oven door.
-
Remove the floor and the plate positioned on top of
the burner.
-
Remove and replace the component.
-
Reassemble all parts. For assembly, proceed in
reverse order.
BURN AND SPARK PLUG REPLACEMENT
-
Open the oven door.
-
Remove the floor and the plate positioned on top of
the burner.
-
Remove and replace the component.
-
Reassemble all parts. For assembly, proceed in
reverse order.
REPLACING THE
THERMOCOUPLE
-
Remove the control panel.
-
Open the oven door.
-
Remove the floor and the plate positioned on top of
the burner.
-
Remove and replace the component.
-
Reassemble all parts. For assembly, proceed in
reverse order.
ELECTRIC HOB
REPLACING THE KNOB AND INDICATOR LIGHT
-
Remove the control panel.
-
Remove and replace the component.
-
Reassemble all parts. For assembly, proceed in
reverse order.
REPLACING THE HOTPLATE.
-
Remove the control panel and internal guards.
-
Remove and replace the component. Screw spacer
M8 taken from the old part onto the new one.
-
Reassemble all parts. For assembly, proceed in
reverse order.
ELECTRIC OVEN
REPLACING THE KNOB AND INDICATOR LIGHT
-
Remove the control panel.
-
Remove and replace the component.
-
Reassemble all parts. For assembly, proceed in
reverse order.
REPLACING THE WORKING THERMOSTAT AND
SAFETY THERMOSTAT
-
Remove the control panel.
-
Remove the bulb from its seat on the side of the
oven.
-
Remove and replace the component.
-
Reassemble all parts. For assembly, proceed in
reverse order.
REPLACING THE HEATING ELEMENT
-
Remove the oven floor (only for lower heating
elements).
-
Undo the screw securing the element to the oven
and pull the element out by approx. 10 cm.
-
Reassemble all parts. For assembly, proceed in
reverse order.
24.CLEANING THE INTERIOR
Check the condition of the inside of the appliance.
Remove any built-up dirt.
Check and clean the fumes exhaust system.
25.MAIN COMPONENTS
GAS HOB
-
GAS COCK
-
MAIN BURNER
-
Pilot burner
-
Thermocouple
GAS SOLID TOP RANGES
-
GAS COCK
-
MAIN BURNER
-
Pilot burner
-
Thermocouple
modular gassolidtop700-900 G23M 16/80

-
Igniter
-
Piezoelectric ignition
GAS OVEN
-
GAS COCK
-
MAIN BURNER
-
Pilot burner (900 series only)
-
Thermocouple
-
Igniter
-
Piezoelectric ignition
ELECTRIC HOB
-
Control knob
-
Hotplate
-
Indicator light
ELECTRIC OVEN
-
Control knob
-
Working thermostat
-
Safety thermostat
-
Heating element
-
Indicator light
modular gassolidtop700-900 G23M 17/80

FR - INSTALLATION –EMPLOI - ENTRETIEN
I. AVERTISSEMENTS
GÉNÉRAUX
LIRE ATTENTIVEMENT CE MANUEL. IL
DONNE DES INFORMATIONS
IMPORTANTES POUR L'INSTALLATION,
L'UTILISATION ET L'ENTRETIEN DE
L'APPAREIL EN TOUTE SÉCURITÉ.
LE DÉFAUT DE SE CONFORMER À CE QUI
EST PRÉSENT
É CI DESSOUS PEUT
COMPROMETTRE LA SÉCURITÉ DE
L'ÉQUIPEMENT.
LE FABRICANT DE L'APPAREIL DÉCLINE
TOUTE RESPONSABILITÉ EN CAS DE
DOMMAGES DÛS AU NON RESPECT DES
CONSIGNES CI DESSOUS.
TRADUCTION
DES INSTRUCTIONS
D'ORIGINE.
LES ÉQUIPEMENTS ONT BESOIN DE
QUELQUES PRÉCAUTIONS POUR
L’INSTALLATION, LE POSITIONNEMENT
ET/OU LE FIXAGE ET LE BRANCHEMENT
ÉLECTRIQUE.
VOIR SECTION
“INSTRUCTIONS POUR L'INSTALLATION”.
LES ÉQUIPEMENTS ONT BESOIN DE
PRÉ
CAUTIONS POUR LE NETTOYAGE.
VOIR SECTION “INSTRUCTION PO
UR LE
NETTOYAGE”.
LE SYMBOLE "HAUTE TENSION" EST
PLACÉ SUR UN PANNEAU QUI DONNE
ACCÈS À UNE PARTIE AVEC HAUTE
VOLTAGE.
Conserver ce manuel dans un endroit sûr et connu
afin de pouvoir le consulter pendant toute la durée
de vie utile de l'appareil.
Cet appareil est conçu pour la cuisson d'aliments. Il
est destiné à un usage industriel. Toute autre
utilisation est réputée impropre.
Cet appareil n'est pas approprié à l'emploi de la
part de personnes (y compris les enfants) avec
capacités physiques,
sensorielles ou mentales, réduites ou sans
expérience ni connaissance.
A moins qu'une personne responsable de leur
sécurité ne les surveille ou les instruit au sujet de
l'utilisation de l'appareil.
Eviter de laisser le dispositif sans survelliance en
présence d’enfants et s’asseurer qu’ils ne l’utilissent
pas ou qu’ils ne journent avec.
Le personnel devant utiliser l'appareil doit avoir
suivi une formation spéciale. Surveiller l'appareil
pendant son
fonctionnement.
NE PAS STOCKER DE SUBSTANCES IN "
AMMABLES À PROXIMITÉ DE L'APPAREIL.
DANGER D'INCENDIE.
Installer l'appareil seulement dans des locaux
suffisamment aérés.
Toujours installer l'appareil dans un local aéré. Une
mauvaise aération peut être la cause d'asphyxies.
Ne pas
obstruer le système d'aération du local où cet
appareil est installé. Ne pas obstruer les bouches
d'aération et
d'évacuation de cet appareil ou d'autres appareils.
En cas de panne ou de dysfonctionnement de
l'appareil, fermer le robinet d'arrèt du gaz et/ou
désactiver l'interrupteur général d'alimentation
électrique installés en amont de l'appareil.
L'installation et la conversion à un autre type de gaz
doivent être effectués par des installateurs qualifiés
et agréés par le fabricant, conformément aux
normes de sécurité en vigueur et aux consignes
données dans ce manuel.
L'entretien et la conversion à un autre type de gaz
de l'appareil doivent être effectués par des
installateurs qualifiés et agréés par le fabricant,
conformément aux normes de sécurité en vigueur
et aux consignes données dans ce manuel.
modular gassolidtop700-900 G23M 18/80

Effectuer le nettoyage conformément aux
instructions données dans le Chapitre “
INSTRUCTIONS POUR LE NETTOYAGE “.
1. ÉLIMINATION DE L'EMBALLAGE ET DE
L'APPAREIL
EMBALLAGE
L'emballage est réalisé dans des matériaux
compatibles avec l'environnement. Les éléments en
matière plastique recyclables sont:
-
la couverture transparente, les sachets du manuel
d'instructions et des injecteurs (en polyéthylène -
PE).
-
les feuillards (en polypropylène - PP).
APPAREIL
L'appareil est réalisé à plus de % dans des matériaux
métalliques recyclables (acier inox, tôle aluminée,
cuivre, etc. ).
L'appareil doit être mis au rebut conformément à la
réglementation en vigueur.
Le rendre inutilisable avant son élimination.
Ne pas le jeter dans la nature.
LE SYMBOLE DE LA POUBELLE BARRÉE
REPORTÉ SUR L’APPAREIL ET LA BOÎTE
INDIQUE QUE LE PRODUIT À LA FIN DE
SA PROPRE VI
E UTILE DOIT ÊTRE
RAMASSÉ SÉPARÉMENT DES AUTRES
DÉCHETS.
LA COLLECTE DIFFÉRENTIÉE DE CET APPAREIL
AYANT ATTEINT LA FIN DE SA VIE EST ORGANISÉE
ET GÉRÉE PAR LE FABRICANT.
LE CLIENT SOUHAITANT SE DÉFAIRE DE CET
APPAREIL DEVRA DONC CONTACTER LE FABRICANT
ET SUIVRE LA PROCÉDURE QUE CE DERNIER A
ADOPTÉE AFIN DE
PERMETTRE LA COLLECTE
SÉPARÉE DE L’APPAREIL ARRIVÉ EN FIN DE VIE.
UNE COLLECTE ET UN TRI DES DÉCHETS CONTRIBUE
A ÉVITER LES POSSIBLES EFFETS NÉGATIFS SUR
L’ENVIRONNEMENT ET SUR LA SANTÉ ET FAVORISE
LA RÉUTILISATION ET/OU LE RECYCLAGE DES
MATÉRIAUX DONT EST COMPOSÉ L’APPAREIL.
L’ÉLIMINATION ABUSIVE DU PRODUIT DE LA PART
DU PROPRIÉTAIRE COMPORTE L’APPLICATION DES
SANCTIONS ADMINISTRATIVES PRÉVUES PAR LES
NORMES EN VIGUEUR.
2. DISPOSITIFS DE SÉCURITÉ
FOUR ÉLECTRIQUE
THERMOSTAT DE SÉCURITÉ
LE FABRICANT DE L'APPAREIL DÉCLINE
TOUTE RESPONSABILITÉ EN CAS DE
DOMMAGES DÛS AU NON RESPECT DES
CONSIGNES CI DESSOUS.
Un thermostat de sécurité à rétablissement manuel
qui coupe le chauffage lorsque la température de
service dépasse celle maximum admise est monté
dans l'appareil.
Pour rétablir le fonctionnement de l'appareil, il faut
enlever le panneau de commandes et appuyer sur
le bouton de rétablissement du thermostat. Cette
opération peut être effectuée uniquement par un
technicien qualifié et agréé.
II. INSTRUCTIONS POUR
L'INSTALLATION
3. AVERTISSEMENTS POUR
L'INSTALLATEUR
LIRE ATTENTIVEMENT CE MANUEL. IL
DONNE DES INFORMATIONS
IMPORTANTES POUR L'INSTALLATION,
L'UTILISATION ET L'EN
TRETIEN DE
L'APPAREIL EN TOUTE SÉCURITÉ.
LE DÉFAUT DE SE CONFORMER À CE QUI
EST PRÉSENTÉ CI DESSOUS PEUT
COMPROMETTRE LA SÉCURITÉ DE
L'ÉQUIPEMENT.
LE FABRICANT DE L'APPAREIL DÉCLINE
TOUTE RESPONSABILITÉ EN CAS DE
DOMMAGES DÛS AU NON RESPECT DES
CONSIGNES CI DESSOUS.
Repérer le modèle d'appareil. Le modèle est indiqué
sur l'emballage et la plaque signalétique de
l'appareil.
Installer l'appareil seulement dans des locaux
suffisamment aérés.
L'installation et la conversion à un autre type de gaz
doivent être effectués par des installateurs qualifiés
et agréés par le fabricant, conformément aux
normes de sécurité en vigueur et aux consignes
données dans ce manuel.
modular gassolidtop700-900 G23M 19/80

L'entretien et la conversion à un autre type de gaz
de l'appareil doivent être effectués par des
installateurs qualifiés et agréés par le fabricant,
conformément aux normes de sécurité en vigueur
et aux consignes données dans ce manuel.
Ne pas obstruer les orifices d'aération et
d'évacuation de l'appareil.
Ne pas manipuler les pièces de l'appareil.
4. NORMES ET TEXTES DE LOI DE
RÉFÉRENCE
Installer le appareils en conformité avec les normes
de sécurité en vigueur dans le pays.
5. DÉBALLAGE
Contrôler l'état de l'emballage et demander au
transporteur d'inspecter la marchandise en cas de
dommages évidents.
Enlever l'emballage.
Enlever la pellicule protégeant les panneaux
extérieurs. Éliminer les éventuels résidus de colle
avec un solvant adapté.
6. MISE EN PLACE
Les dimensions de l'appareil et la position des
raccordements sont indiquées dans le schéma
d'installation figurant à la fin de ce manuel.
L'appareil peut être installé seul ou avec d'autres
appareils de la même gamme.
Cet appareil ne peut pas être encastré.
Installer l'appareil à une distance de 10 cm
minimum des murs.
Si l’équipement doit être mis prés de murs,
séparations, éléments décoratives, etc. ceux-ci
doivent être faits en matériaux incombustibles
Dans le cas contraire ils doivent être couverts avec
matériaux thermo-isolants incombustibles ;
Mettre l'appareil d'aplomb à l'aide des pieds
réglables.
MONTEGE DE L'APPAREIL SUR UN SOCLE EN PONT
Suivre les instructions données avec le type de
support utilisé.
SYSTÈME D'ÉVACUATION DES FUMÉES
Prévoir un système d'évacuation des fumées
conformément au " Type " d'appareil. Le " Type "
est indiqué sur la plaque signalétique de l'appareil.
APPAREIL DE TYPE " A1 "
Mettre les appareils de type “A1” sous une hotte
aspirante pour assurer l'évacuation des fumées et
des vapeurs de cuisson.
APPAREIL DE TYPE "
B21 "
Installer l'appareil de type “B21” sous une hotte
aspirante.
APPAREIL DE TYPE " B11 "
Monter le conduit de cheminée à demander au
fabricant sur l'appareil de type “B11”. Suivre les
instructions de montage jointes au conduit de
cheminée.
Raccorder au conduit de cheminée un tuyau d'un
diamètre de 150/155 mm, résistant à une
température de 300°C.
Poursuivre vers l'extérieur ou dans un conduit de
cheminée effi cace. La longueur du tuyau ne doit
pas dépasser 3 mètres.
7. RACCORDEMENTS
La position et la dimension des raccordements sont
précisées sur le schéma d'installation figurant à la
finde ce manuel.
RACCORDEMENTE À LA CONDUITE DE GAZ
Vérifier si l'appareil est prévu pour le type de gaz
qui l'alimentera. Contrôler les indications sur les
talons figurant sur l'emballage et sur l'appareil.
Si nécessaire, adapter l'appareil au type de gaz
utilisé. Suivre les instructions du Paragraphe
“Adaptation à un autre type de gaz”.
Sur les appareils hauts, un raccordement à l'arrière
est disponible. Dévisser le bouchon et le visser de
façon étanche sur le raccordement avant.
Installer un robinet d'arrêt à fermeture rapide en
amont de l'appareil, dans un endroit facilement
accessible.
Ne pas utiliser de tuyaux de raccordement d'un
diamètre inférieur à celui du raccordement de gaz
de l'appareil.
modular gassolidtop700-900 G23M 20/80