Modus M-247 User manual

DOG TRAINING COLLAR

1
TABLE OF CONTENTS
S/N CONTENTS
1
2
3
4
5
6
WORK PRINCIPLE
FIT THE COLLAR
COMPONENTS
HOW TO CHARGE THE DEVICE
PAIRING OF THE RECEIVER AND REMOTE
WARRANTY
7
8
9
10
TECHNICAL SPECIFICATIONS
11
FUNCTION INTRODUTION
FCC CAUTION
12
SCENARIOS
TURN ON AND OFF
HINTS AND TIPS
WARNING
13
14
WHAT'S IN THE BOX
15 CONTACT US

Thank you for choosing MODUS Dog Training Collar M-247.
MODUS, Pets Intelligent Training Expert.
Please read this manual carefully before using the device.
WORK PRINCIPLES
MODUS Dog Training Collar is specially developed and designed for dog training, which
mainly has two parts: the remote and receiver. It establishes signal connection between
the remote and the receiver through wireless communication technology (the effective
distance is up to 300 meters),and realizes the purpose of long-distance one-click dog
training through the remote sending instruction to the receiver. When the dog behaves
uncivilized, the owner only needs to operate the remote, which can correct the bad
behavior through the functions of sound instruction, recording playback, vibration and
static shock. After a period of time, dogs will gradually develop good civilized behavior.
SCENARIOS
1. The device is suitable both indoor and outdoor.
2. The device can be used as a dog training auxiliary means.
3. The device is not suitable for dogs with any skin lesions around the neck.
4. The device is not suitable for dog under 6 months of age.
5. The device is suitable for all breeds of small, medium and large dogs.
TECHNICAL SPECIFICATIONS
Brand Name: MODUS
Model Number: M-247
Product Material: ABS Flame Retardant
Power: 0.78 W
Remote Battery: 300 mAh Lithium Battery
Receiver Battery: 450 mAh Lithium Battery
Charging: Input 5V DC/1A
Product Dimensions: 4.02*2.37*1.05 inch
Collar Size: 2.95*1.48*1.30 inch
Product Weight: 0.43 lb
Operating Temperature: -4 ℉~104 ℉
Max Operating Distance: 350 yd
Waterproof Level: IP67
1
2
2

WHAT’S IN THE BOX
Collar
3Test Light
4
USB Cable
5
Contact Points
7
Remote Control
1Receiver
2
Wrist Strap
6
Note: If you buy two-dog system, there will be 2 receivers,2 longer contact points and 2 collars.
3

COMPONENTS
Remote
Receiver
4
Sensor Port / Antenna
Indicator Light
Beep Button
Play Record 1
Shock Button
Turn off Shock
/Lock Button
Play Record 2
Vibration Button
Screen
Channel Button
+/- Button
Contact Points
Charging Port
On/off
Indicator Light
Record 2
Record 1
Microphone
Speaker

INSTRUCTIONS
Ⅰ. FIT THE COLLAR
Note: Please make sure the collar is put on dog’s neck firmly, not too tight and
not too loose. The probes must be touching the skin of the dog in order for
effective electric shock.
1. Make sure your dog is relaxed before wearing it (Figure A).
2. Open the collar buckle, adjust the appropriate length to completely surround
the dog's neck, and align the inner microphone with the dog's pronunciation part
(Figure B).
Note: Make sure that both metal detectors pass completely through the dog's
hair and make contact with the dog's skin. If necessary, trim the dog's hair to
ensure good contact.
3. Buckle the dog collar. When the collar is buckled, the collar should be behind
the dog's ear (the uppermost part of the neck).
4. Adjust the collar to the appropriate length until you can put one finger
between the dog's neck and collar. Also make sure that the collar is stable, but
not too tight.
5. Give your dog enough time to adapt to wearing a collar. This step is to ensure
that the collar is still safe and secure in your dog's daily activities.
6. Remove the collar from the dog's neck, cut off the excess material, and
reserve a length of about 1 inch.
7. Seal the edge of the cut collar with flame (Figure C).
8. Put the collar on your dog again and use it after it is installed.
Figure A Figure B
Figure C
5

Ⅱ.Turn On and Off
1. How to turn on/off the remote :
Turn on: press any key to turn on the device, LCD display and backlight will turn on, the
device will be into the normal working mode.
Turn off: the backlight will turn off in 20 seconds without operation, and turn off display
and the device in 40 seconds without operation.
2. How to turn on/off the receiver.
Turn on: After a brief touch with the remote's antenna sensor, it turns on with a “beep”.
Turn off: After a brief touch with the remote's antenna sensor, it turns off with two
“beep”.
Note: In standby mode, green LED of the receiver flashes once every 5 seconds.
2
1
Short touch to start up
6

Ⅲ.How to charge the device?
When purchasing the device, there is a USB cable attached in the packing box. Please
connect the USB cable with the adapter, and then insert it into a charge port like power
transformer, power strip, power bank or computer port to charge the device.
Ⅳ. Switch Channels
Press the “CH” key, you can select the receiver that you want to control. After pairing,
the receiver will only work under this channel. When “ALL” is displayed on the remote
screen, you can control receivers of all channels. (If you purchase the receiver version
separately, you need to manually pair them.)
12
1
2
3
7
120 Minutes
Complete charging in 2 hours.
Offer only one wire in the package.

Ⅴ.Pairing Of The Receiver And Remote
The device works by radio channel communication. The remote and receiver need to be
on the same channel to work properly. Before delivery, we will pair the remote with the
receiver. If remote has lost contact with receiver because of signal interruption or
power outage, please pair manually.
1. Use the remote's antenna sensor to touch the receiver's sensor for about 3-5
seconds until the receiver issues a “beep” and a green light flashes, indicating that it is
waiting for pairing.
2. The receiver will wait for the pairing state for 10 seconds.During this period, it will
quickly flash the green light, then please press the vibration key of the remote within 10
seconds, and the receiver will emit a “beep” when receives the signal, which means the
pairing is completed.
2
1
8
To turn the remote and receiver on.

OPERATING INSTRUCTION
Function Introduction
1. Static Shock Mode
Before using for the first time, you can use the test bulb to test whether it works
properly.
Different dogs have different resistance values. You can gradually use the equipment
when you start to find appropriate electric shock level for your dog.
For initial use, select the minimum static shock for the pet and watch his reaction. If
any adverse reactions occur, please stop immediately.
Press the shock key with remote, and the receiver will release the shock.
2. Vibration & “Beep” Sound Mode
Before using the static shock, you can use the sound and vibration first, which allows
the dog to form a conditioned reflex. It is the safest method of training and helps to
improve the effect of training. You can combine reward training to train your dog to
make a series of actions by vibration or sound. The vibration is divided into level 1-
9,and intensity of the sound is not adjustable. Press the vibration or sound key with the
remote, and the receiver will vibrate or send out a “beep".
12
level 1-9
9
Use electric shock and vibration as needed