modway EEI-3195 User manual

EEI –3195 Office Chair
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 1 of 4
Thank you for purchasing the MODWAY OFFICE CHAIR.
Before you start, here are some helpful advice:
1. We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2. Owing to the size and weight of the chair, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3. Please do not use any tools other than those provided or recommended in these instructions.
4. Please do not throw away any of the packaging or the instruction until you have checked all the components
and hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
and environmentally friendly way.
5. Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten
the components from time to time, so please save the tools that have been provided.
6. Please keep all fitting out of reach of children.
Hardware:
A. Bolt M6x25mm x 6
B. Bolt M6x20mm x 4
C. Flat Washer M6*18mm x 10
D. Bolt 5/16”x7/8” x 3
E. Flat Washer M8*18mm x3
F. Allen Wrench x1
Component:
1 Base x1 2 Cylinder Column x1 3 Control Mechanism x1 4 Seat x1 5 Back Frame x1
6 Left Arm x1 7 Right Arm x1 8 Castor x5 9 Round casing x1
1
8
2
3
4
6
7
5
9

EEI –3195 Office Chair
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 2 of 4
STEP 1:
Please put Base (1) on a carpeted or padded surface.
Insert 1 piece of Castor (8) into the Base (1) as shown by hand. Repeat the same steps for the remaining 4
pieces of Castors (8).
STEP 2:
Carefully turn over the assembled base from step 1.
Insert the Cylinder Column (2) and Round casing (9) as shown.
8
1
8 8
8
1
2
8
9
1
8
2
9

EEI –3195 Office Chair
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 3 of 4
STEP 3:
Attach Left Arm (6) and Right Arm (7) to the bottom of Seat (4) by using 6 pieces of Bolts (A) with 6 pieces of
Flat Washers (C) as shown.
Tighten Bolts (A) by using Allen Wrench (F)as shown.
Hardware & Tools required
STEP 4:
Attach Control Mechanism (3) to the Seat (4) by using 4 pieces of Bolts (B) and 4 pieces of Flat Washers (C)
as shown. Tighten Bolts (B) by using Allen Wrench (F) as shown.
Note: the four Bolts (B) in this step cannot be locked tightly. Fix them with the Bolts (B) first, leaving room for
convenient assembly of Back Frame (5).
A
C
F
FRONT
4
6
7
B
C
F
FRONT
4
3
6
7
A
x 6x 6
x 1
F
C
B
x 4x 4
x 1
F
C

EEI –3195 Office Chair
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 4 of 4
Hardware & Tools required
STEP 5:
Insert the Back Frame (5)to the hole of Control Mechanism (3) hole by using 3 pieces of Bolts (D) and 3 pieces
of Flat Washers (E) as shown.
Tighten Bolts (D) and Bolts (B) in the previous step by using Allen Wrench (F) as shown.
Hardware & Tools required
STEP 6:
Insert Control Mechanism (3) into the Cylinder Column (2) as shown.
Assembly is complete. Your office chair is ready to be used now!
D
x 3x 3
x 1
F
E
D
F
E
FRONT
6
7
5
4
3
3
4
6
7
5
1
8
2
9
2
3