modway MOD-6004 User manual

Thank you for purchasing the MODWAY BED!
Before you start, here are some helpful advice:
1. We suggest you spend a short time reading through this leaflet and then follow the simple step instructions.
2. Owing to the size and weight of the bed, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approx assembly time: 30 minutes.
3. Please do not use any tools other than those provided or recommended in these instructions.
4. Please do not throw away any of the packaging or the instruction until you have checked all the components and
hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
environmentally friendly way.
5. Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save tools that have been provided.
6. Please keep all fitting out of reach of children.
Hardware:
1JCBB BOLT M8 x 16 8 PCS
2JCBB BOLT M8 x 35 8 PCS
3JCBB BOLT M8 x 50 2 PCS
4JCBB BOLT M8 x 60 2 PCS
5 JCBB BOLT M8 x 70 4 PCS
6FLAT WASHER M8 16 PCS
7SPRING WASHER M8 16 PCS
8WOOD SCREW M4 x 32mm 9 PC
9WOOD DOWEL M10 X 30mm 8 PCS
10 M5 ALLEN KEY (BALL SHAPE) 1 PC
Component:
A. HEADBOARD x 1
B. HEADBOARD PANEL x 1
C. FOOTBOARD x 1
D. SIDE RAIL (L&R) x 2
E. LEG x 4
F. CENTER RAIL x 1
G. CENTER SUPPORT LEG x 3
H. BED SLAT x 1
01 of 07
MOD - 6004 QUEEN BED
A
B
C
D
E
F
G
H
I
I. HEADBORAD SUPPORT x 1

STEP 1
1.1 Fasten center support leg (G) to center rail (F) attach by screwing the protruding nut into
the corresponding holes.
1.2 Fit wood dowels (9) into Headboard Panel (B) & Footboard (C).
9. WOOD DOWEL M10 x 30mm x 8pcs
02 of 07
MOD - 6004 QUEEN BED
F
G
B
9
C
9
x 2
x 2

STEP 2
2.1 Insert and secure the headboard support (I) to the headboard (A) using hardware parts
5,6,7 and 10.
5. JCBB BOLT M8 x 70 x 4pcs 7. SPRING WASHER M8 x 4pcs 6. FLAT WASHER M8 x 4pcs 10. ALLEN KEY (BALL SHAPE) M5 x 1pc
3.1 Insert and secure the leg (E) to the side rail (D) using hardware parts 2,6,7 and 10.
Repeat the same for other side of leg.
2. JCBB BOLT M8 x 35 x 4pcs 7. SPRING WASHER M8 x 8pcs 6. FLAT WASHER M8 x 8pcs 10. ALLEN KEY (BALL SHAPE) M5 x 1pc
03 of 07
MOD - 6004 QUEEN BED
10
57
6
I
A
Don't screw tied
x 2
2
7
10
6
E
D
x 2
L
R
STEP 3
x 2

STEP 4
STEP 5
5.1 Insert and secure the headboard (A) to the headboard panel (B) using hardware parts
3,4,6,7 and 10.
4. JCBB BOLT M8 x 60 x 2pcs
05 of 07
MOD - 6004 QUEEN BED
10
1C
D
x 4
x 4
STEP 4.1
STEP 4.2
10
6
4
7
3
7
6
x 2
1. JCBB BOLT M8 x 35 x 8pcs 10. ALLEN KEY (BALL SHAPE) M5 x 1pc
3. JCBB BOLT M8 x30 x 2pcs 7. SPRING WASHER M8 x 4pcs 6. FLAT WASHER M8 x 4pcs 10. ALLEN KEY (BALL SHAPE) M5 x 1pc
4.1 Attach the footboard (C) & headboard panel (B) to the side rails (D)
4.2 Using the JCBB bolt M8 x 35mm x 8pcs (2) using M5 allen key (10).

STEP 6
STEP 7
1. WOOD SCREW M4 x 32 x 9pcs
06 of 07
MOD - 6004 QUEEN BED
F
C
8
H
D
Screw Driver
6.1 Locate center rail (F) into the corresponding brackets inside of headboard panel (B) and
footboard (C).
7.1 Assemble slat (H) into bed frame in between side rail (D) and center rail (F) screw it using
wood screw M4 x 32mm (8).

STEP 8
Assembly is complete. The bed is ready to use now!
NOTE: Hardware may loosen over time. Periodically check that all connections are tight.
07 of 07
MOD - 6004 QUEEN BED
8.1 Carefully position the assembled bed to the desired location by four adults.