modway EEI-2932 User manual

︱ Page 1 of 4
EEI–2932 LOVESEAT
Hardware:
Component:
A Bolt M8x40mm
x 12
Thank you for purchasing the MODWAY LOVESEAT!
Before you start, here are some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the loveseat, we recommend that it is assembled by two adults, on a
carpeted or padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of small children.
B
Allen Wrench M5 x 1
Customer Service 908-368-1025 www.modwayfurniture.com
1. Chair Back x4
2. Chair Seat x2
3. Left Frame x1
4. Right Frame x1
5. Back Cushion x2
6. Seat Cushion x2
7. Batyline x2
8. Middle Frame x1
3
2
2
7
7
5
6
5
6
4
8
1

Customer Service 908-368-1025 www.modwayfurniture.com
STEP 1:
STEP 2:
Please put Left Frame (3) on a carpeted or padded area.
Insert the tenon on Chair Seat (2) into the rabbet on Left Frame (3) at first.
Insert Wooden Bar or Chair Back (1) one by one through the drilling hole.
3
2
Please insert Batyline fabric (7).
Carefully position Middle Frame (8) to the assembled Chair Back (1), Chair Seat (2) and Left Frame (3) as
shown.
Insert the tenon on Chair Back (1) and Chair Seat (2) into the rabbet on Middle Frame (8).
7
3
7
1 2
3
1
2
3
2
Page 2 of 4
EEI–2932 LOVESEAT
8

Customer Service 908-368-1025 www.modwayfurniture.com
STEP 3:
STEP 4:
Carefully turn over the assembled Chair Back (1), Chair Seat (2), Left Frame (3) and Middle Frame (4).
Insert the tenon on Chair Seat (2) into the rabbet on Middle Frame (8).
Next insert Wooden Bar or Chair Back (1) one by one through the drilling hole.
Insert Batyline fabric (7).
Carefully position Right Frame (4) to the assembled Chair Back (1) and Chair Seat (2) as shown.
Insert the tenon on Chair Back (1) and Chair Seat (2) into the rabbet on Right Frame (4).
Page 3 of 4
EEI–2932 LOVESEAT
2
1
7
7
7
3
8
4
2
2

Customer Service 908-368-1025 www.modwayfurniture.com
STEP 5:
STEP 6:
Insert 2 pieces of Bolt (A) into the pre-drilled holes on Chair Back (1) through the top pre-drilled holes on Left
Frame (3).
Insert 2 piece of Bolt (A) into the pre-drilled holes on Chair Seat (2) through the top pre-drilled holes on Left
Frame (3).
Insert 2 piece of Bolt (A) into the pre-drilled holes on Chair Seat (2) through the top pre-drilled holes on Middle
Frame (8).
Use Allen Wrench (B) to tighten Bolts (A) clockwise until secure.
Repeat the same steps for Right Frame (4).
Carefully position the assembled chair to the desired location.
Put Back Cushion (5) and Seat Cushion (6) into the assembled chair as shown.
Ax12 Bx1
5
6
Hardware & Tool required
Assembly is complete. Your loveseat is ready to be used now!
Page 4 of 4
EEI–2932 LOVESEAT
6
5
A
B
B
A