Moe's MS-104 User manual

Wi-Fi + RF
Switch Module
MS-104
User Manual • Uživatelský manuál

Dear customer,
Thank you for purchasing our product. Please read the following
instructions carefully before first use and keep this user manual for
future reference. Pay particular attention to the safety instructions. If
you have any questions or comments about the device, please
contact the customer line.
✉www.alza.co.uk/kontakt
✆[phone]
Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Praha
7, www.alza.cz

Global international operation Whenever &
Wherever You are, All-in-one Mobile App
Schedule
timer
Voice
control-work
with Google
Home Voice
control-work
with Amazon
Alexa Device
Sharing
Anywhere

Inhouse local operation
App
Router
Voice
control
Rocker
light
switch
Installation
Warnings:
1. Installation must be carried out by a qualified electrician in
accordance with local regulations.
2. Keep the device out of the reach of children.
3. Keep the device away from water, damp, or hot environment.
4. Install the device away from strong signal sources such as
microwave oven that ma cause signal interruption resulted in
abnormal operation of the device.
Rocker light
h
Push wall switch

5. Obstruction by concrete wall or metallic materials ma reduce the
effective operation range of the device and should be avoided.
6. Do NOT attempt to disassemble, repair, or modify the device.
Technical specifications
Product type
Wi-Fi + RF Switch Module
Voltage
90-250V AC
Current
10A
Wi-Fi frequency
2.4GHz Wi-Fi
RF frequency
RF433 MHz
Operation temp.
-10°C - +40°C
Case temp.
Tc: +80°C (Max.)
Operation range
≤200 m
Dims (WxDxH)
52x47x18 mm
IP rating
IP20
Warranty
2 years

Wiring diagram
1. With one switch
2. Without switch

3. With 2 Way switches
4. With Wall Socket
Wiring Instructions and Diagrams
1. Turn off the power supply before carrying out any electrical
installation work.
2. Connect wires according to the wiring diagram.
3. Insert the module into the junction box.

4. Connect the power supply and follow switch module configuration
instructions.
NOTES:
Put your smartphone close to the switch module when ou are
configuring, and make sure you have min. 50% Wi-Fi signal.
FAQ
Q1: What should I do if I cannot configure the switch module?
a. Please check whether device is powered on.
b. Make sure your mobile and switch module are under the same 2.4
GHz Wi-Fi network.
c. Whether it is in good internet conditions.
d. Make sure the password entered in App is correct.
e. Make sure the wiring is correct.
Q2: What device can be connected to this Wi-Fi switch module?
Most of your household electrical appliances can be, such as lamps,
launder machine, coffee maker, etc.
Q3: What happens if the Wi-Fi goes off?
You can still control the device connected the switch module with
your traditional switch and once Wi-Fi is active again the device
connected to module will connect automatically to your Wi-Fi
network.
Q4: What should I do if I change the Wi-Fi network or change the
password?

You must re-connect Wi-Fi switch module to the new Wi-Fi network
according to the App User Manual.
Q5: How do I reset the device?
Power on/off device 5 times until the beeper on module sounds
continuously.
Manual override
The switch module terminal reserves the access of manual override
function for the end-user to switch on/off.
Switch on/off permanent on/off function.
NOTES:
1. Both the adjustment on App and switch can be reset, the last
adjustment remains in memory.
2. The App control is synchronizing with the manual switch.

APP USER MANUAL
iOS App / Android App
Scan the QR code to download Smart Life App, or you can also search
keyword “Smart Life” at App Store or Google play to download App.
Log in register your account with your mobile number or e-mail
address. Type in the verification code sent to your mobile or mailbox,
then set your login password. Click “Create Family” to enter the App.

Wi-Fi link method: (two pairing methods)
Complete the wiring of the switch module before pairing
Method one:
Pair and clear up the Wi-Fi code with Bluetooth and Wi-Fi connected
meantime. (New Updated)
1. Make sure your phone is connected to Wi-Fi and Bluetooth.
Rocker light
switch
Push wall
switch (Reset
switch)

2. Open Smart Life / Tuya App and Click “+”, then the prompt page
will automatically show on the screen. Click “Go to add”.
3. Select the device you want to add and click “+”.

4. Enter Wi-Fi Password and click “Next”, waiting for completing the
connection.

5. Add the device successfully, you can edit the name of the device to
enter the device page by click “Done”.
How to reset Wi-Fi code
a. For reset switch: press the switch button for 10 times until the
beep sounds continuously and rapidly as Di-Di-Di… for pairing and
reset mode.
b. For rocket light switch: press the switch button for 20 times until
the beep sounds continuously and rapidly as Di-Di-Di… for pairing
and reset mode.
NOTE:
This Wi-Fi + RF switch module fits for rocker light switch and reset
switch meanwhile. Please pay attention to the different pairing
modes.

Method two:
Pair with traditional pairing method. After the wiring of switch
module is done, press the traditional switch to enter the pairing
mode.
a. For reset switch: press the switch button for 10 times until the
beep sounds continuously and rapidly as Di-Di-Di… for pairing and
reset mode.
b. For rocket light switch: press the switch button for 20 times until
the beep sounds continuously and rapidly as Di-Di-Di… for pairing
and reset mode.
Open the App, select “+” on top right and choose “Switch (Wi-Fi)” to
add device.

Make sure your smart phone and Wi-Fi + RF switch module are under
the same Wi-Fi network at 2.4GHz connection. Confirm when the light
blinks rapidly (twice a second).
The connecting will take about 10-120 seconds to complete
depending on your network condition.

When pairing is done, the switch will be shown on the App.
Connect to Amazon Alexa or Google Assistant for voice control or
share the devices with your families or friend.

Enjoy your smart life of home automation for lighting control by
using our All-in-one mobile App wherever you are in the world or
simply by voice control when you are sitting at home comfortably.
Pair and clear up the RF code
1. How to pair the RF code
a. For reset switch: press the switch button for 5 times until do you
hear Di-Di (2 times). Then the matching of RF code is successful.
b. For rocket light switch: press the switch button for 10 times
(ON/OFF cycle for 5 times) until do you hear Di-Di (2 times). Then the
matching of RF code is successful.
App Control
Voice
Control

2. How to clear up the RF code
a. For reset switch: press the switch button for 5 times until do you
hear Di-Di (2 times), waiting for 5 seconds, press the switch button for
5 times again until do you hear Di-Di-Di-Di (4 times). Then the RF code
is now cleared up.
b. For rocket light switch: press the switch button for 10 times
(ON/OFF cycle for 5 times) until do you hear Di-Di (2 times), waiting
for 5 seconds, press the switch button for 10 times (ON/OFF cycle for
5 times) again until do you hear Di-Di-Di-Di (4 times). Then the RF
code is now cleared up.
How to achieve multi-control association
NOTE:
Please confirm you have successfully finished the Wi-Fi link method
above for adding this switch to your Smart Life App before the
association.
1. Wi-Fi- add another smart switch to the same Smart Life / Tuya App.
(If there is a smart switch having been added before to the app, just
go to next step.)
NOTE:
There is no need to wire the new added switch to the light, only L and
N are required for wiring.
2. Then you will see two devices in the app and click the main switch
(as One gang switch below) by entering the next operation.

3. Click in the upper right corner and choose “Multi-Control
Association” and then click “+” in the right corner.
4. Choose the switch that you want to associate to and then choose
the switch button that you want to control the same light.
5. Then go back to previous page, you will see two items in the page,
one is your main switch, the other is the one you associate just now.
NOTE:
Please confirm the associated switch is enabled.
New Added
Main Switch